Copolymerization of bromophenylmaleimide with ethyl or butyl methacrylate

N‐p‐Bromophenylmaleimide (BrPMI) does not polymerize in solution by conventional free radical mechanism. However, it readily polymerized in bulk when mixed with a free radical initiator and heated in a microwave oven for 7–8 min. Copolymerization of ethyl methacrylate or butyl methacrylate with BrPMI was conducted in dioxane. The copolymers were characterized by IR and ¹H NMR spectroscopy and gel permeation chromatography. The monomer reactivity ratios were calculated by a non‐linear least‐square analysis. Thermal analysis indicated a great improvement in thermal stability of the copolymers compared with the methacrylate homopolymers. BrPMI was also polymerized in bulk in the DSC pan, which allowed the calculation of the activation energy of its polymerization. Copyright © 2003 Society of Chemical Industry     

Possibilities and extension of XRD material response analysis in failure research for the advanced evaluation of the damage level of Hertzian loaded components

Due to clearly distinguishable damage symptoms, it is differentiated between the surface and sub‐surface failure mode of rolling bearings. Material states red out by X‐ray diffraction (XRD) residual stress measurements point to a variety of loading conditions especially at raceway surfaces that are associated with several competing failure mechanisms. The corresponding lifetime reduction can range from the lower fatigue strength region to material ratcheting in extreme cases. Relevant position of the microstructural changes and nature of the failure mechanisms are characterized. The time alteration of the XRD material parameters measured at or near the surface and at the depth of the maximum equivalent stress correlates, in a different manner, with the statistical parameter of the 10 % bearing life. Both failure modes are illustrated by concrete examples. Contaminated lubricant and boundary lubrication, which represent practically important surface‐induced failures, are discussed in more detail. Gray staining, i.e. shallow pitting, often occurs without distinct indication of global material aging by means of XRD characteristics. Here, scanning electron microscopy observations and electron microprobe analyses point to corrosion fatigue as acting surface failure mechanism. The interaction between material and lubricant under complex loading regimes particularly of mixed friction and corrosion opens further failure research areas in the field of tribology.     

管壳式换热器流场三维数值模拟

采用多孔介质方法 ,在PHOENICS 3 3程序的基础上建立了换热器的三维流动计算模型。引入体积穿透率、表面穿透率、分布阻力等来描述换热器内的管束。模型通过计算Halle等[1] 的实验工况来进行验证 ,并尝试用于计算 2 0 0MW低温供热堆主换热器内的流场     

Pyrolysis of tertiarybutylphosphine at low pressure

The pyrolysis of tertiarybutylphosphine (TBP) has been studied in the low pressure conditions used for chemical beam epitaxy (CBE). The pyrolysis studies were carried out in low pressure reactors of two different configurations, one of which is a cracker cell designed for use in a CBE system. The reaction products were studied using a quadrupole mass spectrometer. The products observed are accounted for by a reaction mechanism involving homolysis of the parent TBP molecule to produce PH₂ and C₄H₉ radicals. These undergo subsequent reactions to form the stable products C₄H₈, PH₃ and H₂, with smaller amounts of P and P₂ being produced. The production of the sub-hydride PH₂ using this cracker cell design indicates that the use of partially cracked TBP may be a promising technique for reducing the amount of carbon incorporated into the growing epitaxial layer.     

面流消能近底紊动流速特性的研究(面流消能试验研究之一)

本文主要论述了面流消能五种典型流态近底紊动流速特性,总结出了近底时均流速和紊动强度沿程变化规律,提出了近底紊动流速可能出现的最大瞬时值及相应位置的计算公式。面流消能工程的下游防冲设计中考虑的主要水力参数之一是,消能段近底流速紊动可能出现的最大瞬时值及其相应的部位,但目前国内外研究成果较少。笔者通过水工模型试验重点研究了面流消能各典型流态近底流速及其紊动纵向分量沿程的变化规律,并提出了计算公式,为优化面流设计提供科学依据。     

Effect of processing history on the properties of Ag-based tapes

The Bi-system tapes and coils were prepared by the powder-in-tube method. The effect of processing and heat treatment on the properties of the tapes and coils was studied. It is found that the shearing stress produced by the rolling process may destroy the 2223 phase, and the destroyed 2223 phase cannot be recovered by heat treatment, whereas the pressing stress produced by the uniaxial pressing process only makes the 2223 phase grains break, and the broken 2223 phase can be closed by the heat treatment. TheJ _c values of the rolling samples, pressing sample, and the coil with a diameter of 35 mm are over 1.3×10⁴, 2.5×10⁴, and 4×10³ A/cm² (77 K, 0 T), respectively.     

High-pressure dc sputtering of High-Tc BPSCCO thin films withTc(0) above 100 K

High-T _c Bi(Pb)-Sr-Ca-Cu-O thin films have been made on single-crystal MgO substrates using high-pressure dc sputtering technique. X-ray studies confirm the crystallinity and highly oriented structure withc-axis perpendicular to the substrate. By optimizing the annealing schedule the formation of the high-T _c phase is stabilized. The best film exhibited superconducting transition temperature with zero-resistance temperature,T _c(0), as high as 101 K. Temperature dependence ofJ _c indicates the presence of Josephson-type weak links.     

Evolution of BET internal surface area in glassy carbon powder during thermal oxidation

It is demonstrated that glassy carbon powder can be thermochemically activated. During activation, a film with open pores is created on the glassy carbon particles. This film has a large internal surface area, which is accessible to liquids and gases. A simple model for the evolution of the internal surface area in glassy carbon powder during thermochemical gas-phase oxidation is also presented and compared with experimental data. Experimental results are in qualitative agreement with the model. We found that a sharp particle size distribution is desirable with regard to potential technical applications.