采用离散元法分析路面结构的疲劳特征

为了在考虑疲劳损伤和恢复性能的基础上,获取路面结构在重复荷载作用下的疲劳特征,采用离散元方法建立了路面结构模型,并分析了在正弦重复荷载作用下路面结构沥青层底部的受力特性.由于路面荷载的随机性,分别以荷载大小、荷载间歇时间、荷载作用次序为考察对象,分析其对路面结构沥青层底受力特征的影响.研究结果表明:随着周期荷载作用次数的增大,沥青层底部拉应力快速增大至某一基础值,并在此基础值附近呈周期性波动,拉应变则在以一定幅值波动的同时,呈现整体水平先急剧增大后缓慢增大的规律;延长荷载作用的间歇时间,虽然一定程度上增大了拉应力和拉应变的波动幅值,但却显著降低了沥青层底拉应力和拉应变的整体水平;不同的荷载作用次序在沥青层底引起的应力应变状态不同,从小至大序列的荷载对沥青层造成的损伤明显小于从大至小序列的荷载.     

双洞口配筋砌块砌体框支墙梁试验

为研究双洞口配筋砌块砌体框支墙梁地震前后的受力模式,在拟动力子试验前后进行了底层框架配筋砌块短肢砌体剪力墙结构三层足尺模型的竖向力静载试验.试验结果表明:托梁与上部墙体表现出良好的协同工作能力,其工作模式为拉杆拱.通过对其在拟动力试验前后的受力模式进行了比较,可知带洞口配筋砌块砌体框支墙梁结构体系在墙体受到一定损伤时,并不会使墙梁的受力机理发生明显改变.     

改性纤维素增强丙烯酰胺水凝胶的合成与拉伸性能研究

采用水媒法制备了低取代度羧甲基纤维素,并用接枝聚合法制备了改性纤维素/丙烯酰胺水凝胶,考察了单体质量比、取代度等对水凝胶拉伸性能的影响.结果表明:对于接枝聚合反应,采用低取代度羧甲基纤维素可以提高纤维素的有效用量;当交联剂用量为180 mg/L、引发剂1 300 mg/L、低取代度羧甲基纤维素和丙烯酰胺质量比在1∶4 ～ 1∶4.5之间、单体质量分数为30%时,合成水凝胶的拉伸强度达到0.28 MPa;在此基础上,适量添加15%的淀粉可使水凝胶拉伸强度达到0.47 MPa;添加1%二氧化钛可使水凝胶拉伸强度达到0.38 MPa.     

应力吸收层沥青混合料的低温抗裂性能

通过对自主研发的Sampave等3种改性沥青结合料和不同级配的应力吸收层沥青混合料进行低温弯曲和低温蠕变试验,分析沥青结合料和矿料级配对应力吸收层沥青混合料低温抗裂性能的影响.结果表明:自主研发的Sampave特种改性沥青混合料具有优良的低温抗裂性能,但单一改性剂SBR改性沥青并不能达到应力吸收层沥青结合料的性能要求;矿料4.75 mm、0.075 mm筛孔通过率对其低温抗裂性能影响较敏感.     

Pressureless low temperature sintering of nanocrystalline zirconia ceramics via dry powder processing

Pressureless sintering approaches provide a simple avenue to manufacture dense ceramic parts with minimal processing equipment, but current pressureless sintering techniques have yet to demonstrate capabilities of producing dense ceramics while maintaining sub-50 nm grain sizes. Nanocrystalline yttria stablized zirconia ceramics were process from 4 mol% yttria stablized zirconia (4YSZ) nanopowders with a crystallite size of 7.5 nm using dry cold isostatic pressing (CIP) where powders are dried immediately prior to green compact formation and CIP vacuum bagging. It is shown that CIP pressures >75 000 psi (517 MPa) effectively remove pores larger than 100 nm and that pressureless sintering occurs at reduced temperatures for green densities ≥50%. Though the sintering kinetics are shown to be similar to other zirconia nanopowder sintering studies, the small initial crystallize size and reduced sintering temperature allowed densities as high as 97.2%, while retaining a ceramic grain size at or below 40 nm. Produced nanocrystalline 4YSZ ceramics with a grain size of 30.3 nm and a density of 96.3% had Vicker's hardnesses as high as 14.2 GPa and Vicker's indentation fracture resistance of 3.43 MPa·, demonstrating that simple processing approaches can be refined to fabricate nanocrystalline ceramics while maintaining high hardness and indentation fracture resistance.     

Effects of silicone oil and polymeric modifiers on the mechanical properties of highly filled LLDPE

The effects of coupling agents, silicone oil, and three types of polymeric modifiers on the mechanical properties of linear low density polyethylene (LLDPE) composites highly filled with aluminium hydroxide [Al(OH)₃] were studied. Polymeric modifiers that contain polar groups, such as silane‐grafted polyethylene (Si‐g‐PE) and acrylic‐acid‐grafted ethylene‐vinyl acetate copolymer (AA‐g‐EVA), improve the mechanical properties dramatically, while nonpolar modifiers improve them to some extent. When Al(OH)₃ was treated using a titanate coupling agent, the silicone oil increased the impact strength and elongation at break of the LLDPE/Al(OH)₃ composites. Introduction of a polymeric modifier containing polar groups destroys the beneficial effects of silicone oil on film mechanical properties, while the introduction of a nonpolar elastomeric polymeric modifier retains the high impact strength and elongation at break. SEM analyses provide the indirect evidence of the encapsulation of silicone oil around the filler. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 121–128, 2002     

大内跨小边跨框架结构预应力筋优化布置方法

预应力筋的优化布置是大内跨小边跨的多跨预应力混凝土框架结构合理设计计算的关键.为满足控制截面承载力最大的需要,以往常将大跨所需预应力筋布置为连续曲线,并按水平直线延伸通过其相邻的两小跨,按这种布置方式仅使大跨内产生竖向向上的预应力等效荷载,可较好平衡大跨的竖向外荷载;而若将大跨及相邻的两小跨统一考虑,预应力筋按连续曲线布置,张拉产生的预应力等效荷载不但可有效平衡大跨的竖向外荷载而且也可平衡小跨的竖向外荷载,可以使荷载平衡得到优化实现.以一典型工程为例,分析了在相同条件下两种预应力筋布置过程中张拉引起的综合弯矩、主弯矩和次弯矩的分布和量值上差异,比较了两类布筋形式对正截面承载力计算结果的影响,验证了对大内跨小边跨框架结构统一考虑后整体上按三段连续正反抛物线预应力筋布置的合理性.     

Design of the low power wake-up receiver for internet of things communication

A wake-up receiver with high energy efficiency and low power consumption is proposed for solving the power consuming problems of wireless nodes communication in the Internet of Things. The proposed wake-up receiver based on the wake-up mechanism can effectively schedule the network nodes communication, and use the simple envelope detection structure to achieve frequency down-conversion, which can flexibly manage energy and reduce power consumption. Based on UMC 65nm CMOS process technology, the wake-up receiver is designed and simulated. The results show that it can achieve S₁₁ of -21dBm and a sensitivity of -75dBm at a data rate of 1Mb/s, when operating at the central frequency of 780MHz and input signal adopting an on-off keying (OOK) modulation, and the power consumption is 82μW at 1.2V voltage supply.     

论焊接结构生产的技术改造

本文讨论了焊接结构生产技术改造的有关问题，包括总思路及总目标、自动化的基本框架、按低成本自动化的原则设计生产线和关键技术问题的论述。     

棒线材连轧中的微张力闭环控制

介绍了棒线材连轧中微张力闭环控制的基本思想及方法，并分析了微张控制技术的应用条件。