小纸层析法快速测定^99mTc—HMPAO放射化学纯度

采用小纸层析系统１：１的氯仿／四氢呋喃展开剂分析＾９９ｍＴｃ－ＨＭＰＡＯ的放射化学纯度，并与两个薄层析系统和一个纸层析系统的方法作比较。配对ｔ检验结果表明两种方法测定的放射化学纯度无显著差异；放射化学纯度在７４．２％－９６．４％，小纸层析法与薄层／纸层析法紧密相关，回归公式ｙ＝１．００６ｘ－０．３２３。     

Series resonant ZCS‐PFM DC‐DC power converter with high‐frequency high‐voltage transformer link for high‐power magnetron drive

This paper presents a single lossless inductive snubber‐assisted ZCS‐PFM series resonant DC‐DC power converter with a high‐frequency high‐voltage transformer link for industrial‐use high‐power magnetron drive. The current flowing through the active power switches rises gradually at a turned‐on transient state with the aid of a single lossless snubber inductor, and ZCS turn‐on commutation based on overlapping current can be achieved via the wide range pulse frequency modulation control scheme. The high‐frequency high‐voltage transformer primary side resonant current always becomes continuous operation mode, by electromagnetic loose coupling design of the high‐frequency high‐voltage transformer and the magnetizing inductance of the high‐frequency high‐voltage transformer. As a result, this high‐voltage power converter circuit for the magnetron can achieve a complete zero current soft switching under the condition of broad width gate voltage signals. Furthermore, this high‐voltage DC‐DC power converter circuit can regulate the output power from zero to full over audible frequency range via the two resonant frequency circuit design. Its operating performances are evaluated and discussed on the basis of the power loss analysis simulation and the experimental results from a practical point of view. © 2005 Wiley Periodicals, Inc. Electr Eng Jpn, 153(3): 79–87, 2005; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20126     

Fabrication of blue-light emission fused-silica substrates by using Si-ion implantation and high-temperature annealing

We fabricated fused-silica substrates which emit blue light by using Si-ion implantation and high-temperature annealing. Photoluminescence peak wavelengths are around 400 nm, and the peak intensities can be remarkable after annealing above 1150 °C.     

A simplified cascade current‐source inverter interconnected to a single‐phase three‐wire distribution system and its application to electric energy storage systems with batteries

A novel current source inverter system interconnected to the single‐phase grid is proposed. It has the same construction as the conventional three‐phase current source inverter that is interconnected to the single‐phase three‐wire distribution system. Though the proposed circuit has no output transformer, it can be equivalently performed as the single‐phase double cascade inverter by diverting the pole transformer in the utility system. By controlling the appropriate scheme, the output currents can be obtained as the five‐level waveforms and their distortions can be decreased sufficiently. It is applied to the interactive electric energy storage system with batteries and the basic discharging characteristics are discussed experimentally. © 2004 Wiley Periodicals, Inc. Electr Eng Jpn, 150(2): 50–61, 2005; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.10380     

Authority updating: An expert authority evaluation algorithm considering post‐evaluation and power indices in social networks

In group assessment, the focus is on finding high‐authority experts to improve the reliability of assessment results. In this study, we propose an authority updating algorithm while considering the power and judgement reliability of an expert on the basis of social networks and post‐evaluations. A network power index is established and used to reflect the power of an expert while considering social networks. The measurement of the judgement reliability of an expert considers the post‐evaluation of the objects selected by experts, thereby more scientifically reflecting the reliability of experts. The analysis shows the following: although the social‐network structure influences the authority of experts, the influence weakens when the assessment group is a highly or even fully connected group; the network effect may increase the authority of some experts and reduce that of others, and it will weaken as the network connectivity increases; moreover, the judgement reliability and authority of an expert while considering post‐evaluation can encourage him/her to make fair assessments and strive to reduce his/her motivation and cognitive biases.     

Positive state‐bounding observer for positive interval continuous‐time systems with time delay

This paper is concerned with the problem of positive observer synthesis for positive systems with both interval parameter uncertainties and time delay. Conventional observers may no longer be applicable for such kind of systems due to the positivity constraint on the observers, and they only provide an estimate of the system state in an asymptotic way. A pair of positive observers with state‐bounding feature is proposed to estimate the state of positive systems at all times in this paper. A necessary and sufficient condition for the existence of desired observers is first established, and the observer matrices can be obtained easily through the solutions of a set of linear matrix inequalities (LMIs). Then, to reduce the error signal between the system state and its estimates, an iterative LMI algorithm is developed to compute the optimized state‐bounding observer matrices. Finally, a numerical example is presented to show the effectiveness and applicability of the theoretical results. Copyright © 2011 John Wiley & Sons, Ltd.     

Soap‐free emulsion copolymerization of perfluoroalkyl acrylates in the presence of a reactive surfactant

Soap‐free emulsion copolymerization of perfluoroalkyl acrylate (FA)/methyl methacrylate (MMA)/n‐butyl acrylate (n‐BA) was carried out in the presence of sodium 2‐acrylamide‐2‐methyl propanesulfonate (AMPSNa) as a reactive surfactant and potassium persulfate (KPS) as an initiator. An analysis of the effects of concentration of AMPSNa, KPS, FA as well as polymerization temperature on the kinetic features (rate of polymerization) and colloidal characteristics (mean particle diameter, particle disperse index, particle numbers, and surface charge density) was followed. NMR, FTIR, AFM, and fluorine‐selective electrode analysis were used to characterize the composition and morphology of the FA copolymers. Both AFM analysis and contact angle measurements strongly implied that the fluorinated segments migrated to the outmost surface and created films with lower surface energy. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 2438–2444, 2007     

Assessing the predictive capability of two‐phase models for the mechanical behavior of alumina/epoxy nanocomposites

A review of analytical modeling of particulate reinforcement is made as a prelude to the problem of microstructural inhomogeneity in nanocomposite materials. Noting the inevitability of dispersion nonuniformity, and variations in agglomerate morphology and filler‐matrix interaction, the need to question the application of such models to novel materials arises. Employing the mechanical properties of alumina/epoxy nanocomposites, with known dispersion characteristics, an evaluation of the predictive capability of various models for Young's modulus, strength, and failure strain is made. Comparison between models is accompanied by a discussion of the parameters used in the fitting of macroscopic behavior to microstructural features. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 869–879, 2005     

Composites based on eucalyptus tar pitch/castor oil polyurethane and short sisal fibers

Polymeric materials are being developed with renewable resources to promote industrial progress with environmentally friendly technologies. For this reason, polyurethane samples were prepared with 4,4′‐diphenylmethane diisocyanate (NCO/OH = 1), eucalyptus tar pitch (biopitch), castor oil as a polyol, and dibutyltin dilaurate as a catalyst. These materials were reinforced with different contents of short sisal fibers (0, 2.5, 5.0, 7.5, and 10.0%) and were prepared by resin‐transfer molding. The composites were characterized by IR absorption spectroscopy, thermal analysis (thermogravimetry and differential scanning calorimetry), impact resistance, scanning electron microscopy, and water absorption resistance. These materials showed hydrophobic characteristics, despite the addition of sisal fibers. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 3797–3802, 2003     

Vinyl‐containing silicone resin as the crosslinking agent of heat‐curable silicone rubber

Heat‐curable silicone rubber (HCSR) was prepared by using vinyl‐containing silicone resin (VSR) as the crosslinking agent instead of polyvinylsilicone oil (C gum). Mechanical properties and crosslink density of the vulcanizates were measured. The results indicate that VSR is a good crosslinking agent for HCSR. The tensile strength, tearing strength, elongation at break, and hardness of the vulcanizate can reach 10.2 MPa, 29.1 kN/m, 720%, and 58 SHA, respectively. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 3123–3127, 2002; DOI 10.1002/app.10054