PROGRESS IN THE MODELLING OF AIR FLOW PATTERNS IN TIMBER KILNS

Progress in modelling air flow patterns in timber kilns using Computational Fluid Dynamics is reviewed in this work. These simulations are intended to predict the distribution of the flow in the fillet spaces between boards in a hydraulic model of a timber kiln. Here, the flow regime between the boards is transitional between laminar and turbulent flow, with Reynolds numbers of the order of 5000. Running the simulation as a transient calculation has shown few problems with convergence issues, reaching a mass residual of 0.2% of the total inflow after 40-100 iterations per time step for time steps of 0.01 s. Grid sensitivity studies have shown that non-uniform grids are necessary because of the sudden changes in flow cross section, and the flow simulations are insensitive to grid refinement for non-uniform grids with more than 300,000 cells. The best agreement between the experimentally-measured flow distributions between fillet spaces and those predicted by the simulation have been achieved for (effective) bulk viscosities between the laminar viscosity for water and ten times that value. This change in viscosity is not very large (less than an order of magnitude), given that effective turbulent viscosities are typically several orders of magnitude greater than laminar ones. This result is consistent with the transitional flows here.     

Homogenization of hardness distribution and distortion in high pressure gas quenching

Quenching with gases rather than oil or other liquid media has the advantages of reducing the risks concerning health and environment, while simultaneously homogenizing the quenching results and minimizing distortion due to a wide range of possible process parameter variations and the pure convective heat transfer. In this contribution, a coupled solution for increasing homogenization of quenching results within high pressure gas quenching will be presented. In the first stage, an experimental test facility was set up for flow investigations and in the second stage a numerical simulation model was generated. The numerical and experimental results of the flow through the chamber were compared for several boundary conditions. Finally, after complete verification of the simulation, the model may be used to assist in parameter variation for optimization of homogeneous high pressure gas quenching.     

Flow stress of high density polyethylene and nylon 66 at high rates of strain

Measurement of the flow stress of high density polyethylene (HDPE) and nylon 66 at strain rates of 10³ s^?1 using a split Hopkinson pressure bar technique is discussed. The flow stress at a strain of 10% has been determined for both polymers at 20°C. The intrinsic errors involved in this technique are briefly reviewed. The results indicate that the flow stress of HDPE and nylon 66 were 50MPa and 150MPa, respectively, at strain rates of about 10³s^?1.     

A novel direct aerodynamically assisted threading methodology for generating biologically viable microthreads encapsulating living primary cells

In a recent discovery, coaxial electrospinning was explored to encapsulate living organisms within a continuous bio‐polymeric microthread from which active biological scaffolds were fabricated (Townsend‐Nicholson and Jayasinghe, Biomacromolecules 2006, 7, 3364). The cells were demonstrated to have gone through all expected cellular activity without their viability being compromised. These biologically active threads and scaffolds have direct and tremendous applicability from regenerative to therapeutic medicine. Currently these post‐processed cells as composite threads and scaffolds are being investigated in‐depth at a cellular level to establish if the processing methodology has any affect on the cellular make‐up. We now demonstrate a competing non‐electric field driven approach for fabricating composite threads and scaffolds influenced only by a differential pressure. We refer to this novel composite thread to scaffold fabrication methodology as coaxial aerodynamically assisted bio‐threading (CAABT). Our investigations firstly, demonstrate that this technique can process handle living organisms without biologically perturbing them in anyway. Secondly the process is elucidated as possessing the ability to form composite active threads from which biologically viable scaffolds are formed. Finally our study employs florescent activated cell sorting (FACScan), a method by which the cellular dynamics and viability are quantified on control and threaded cellular samples at two prescribed time points. In parallel with FACScan, optical comparison of cellular morphology at three time points within a period of three weeks is carried out to photographically observe any changes in the post‐processed cellular phenotype. Our developmental investigations into this novel aerodynamically assisted threading methodology has unearthed a unique biomicrofabrication approach, which joins cell electrospinning in the cell threading to scaffold fabrication endeavor. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Sheet molding compound characterization using spiral flow

Sheet molding compound (SMC) is a fiber‐reinforced polymeric composite. It is often used in automotive, marine, and industrial applications over other materials because of its high strength to density ratio, resistance to corrosion, and low cost. There is a demand in the SMC industry to be able to characterize SMC processability. This is particularly true for heavy truck body panels, one of the fastest growing applications of SMC. Because of their large size and high strength requirement, the molding forces have a major influence in the molding cycle. Also because of the long flow paths involved, the ability of the paste to carry glass needs to be properly characterized when developing new SMC materials. In this article, we demonstrate the benefits of using spiral flow as a processability tester. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Stability of Periodically Unsteady Axisymmetric Jet

To date, the majority of studies on stability of axisymmetric jets have been completed under the assumption of steady mean flow. Yet, many of the natural and man-made flows that are modeled by these jets can have an inherent unsteadiness; the effects of which on the stability and transition have not been determined. Moreover, controlled unsteadiness can be used to control stability and possibly the transition to turbulence. In this note, the effects of periodic variations of the mean flow on the stability of axisymmetric jets are examined. The problem is treated analytically. The results show that the governing equations and dispersion relation for the unsteady jet can be reduced to those governing the steady jet with a time transformation. It is shown that the periodic variations in the mean flow cause amplitude and phase modulations of the unstable modes. The implications of the modulations on the subsequent transition stages are discussed.     

Fire performance of wood (Pinus radiata) treated with fire retardants and a wood preservative

In this work, we co‐formulated an oil‐borne copper naphthenate/permethrin wood preservative system with synthetic polymer‐based fire‐retardant additives prior to the impregnation of Pinus radiata sapwood. We evaluated what effect, if any, the preservative had upon the fire performance properties of the fire retardants and whether the fire retardants impacted on the fungicidal and termiticidal efficacy of the preservative. The fire retardants included halogenated and phosphorus‐based systems. A mass loss calorimeter, in conjunction with a thermopile, was used to measure the time to ignition and the peak heat release rate (PHRR) from which the fire performance index (FPI) was determined. The preservative properties were evaluated using termite and soil‐block decay bioassays. In summary, we found that the rate of fire growth was reduced when the fire retardants were used in combination with the wood preservative. We also found that the PHRR was a better determinant of fire performance than the FPI. The performance of the wood preservative was enhanced against fungal decay and termite attack when used in combination with the fire retardants. The fire retardants also demonstrated some wood preservative properties of their own. Copyright © 2008 John Wiley & Sons, Ltd.     

The weight vector theory of Coriolis mass flowmeters

In this paper a fuller and clear derivation of the weight vector theory of Coriolis mass flowmeters is given indicating its potential for the prediction of velocity profile effects in both the traditional kind of meter (vibrating tube) and the compact kind (vibrating element inside a duct).     

Heat and Mass Transfer Analogy Studies of Binary Liquid Mixture in Comparison with Eteanol-n-Heptane Evaporating to Air

An expenmental and theoretical study of heat and mass transfer analogy and a comparison of that to a binary liquid mixture evaporation is presented. Common organic solvents, ethanol and n-heptane, were used to form an alcohol - hydrocarbon mixture. Studies were carried out in a horizontal rectangular channel having air flow velocities of 0.2 - 0.9 m/s. Heat transfer coefficients were measured with a copper plate resistor and mass transfer coefficients with a square pool. The heat and mass transfer analogy is presented for a system having two evaporating compounds with a fixed value of air flow and verified by measuring and comparing mass transfer coefficients for distilled water with air flow velocities of 0.2 - 0.9 mls. An illustrative example of the use of the theory for industrial ventilation is presented.