论普通型胶辊表面不处理的合理工艺参数

论述了普通胶辊表面不处理的性能特点和存在问题，技术措施和合理工艺参数，提高了成纱条干水平，减少缠绕和磨损。     

化学成分和固溶温度对1Cr17Mn9Ni4N不锈钢组织和性能的影响

为提高1Crl7Mn9Ni4N钢固溶处理后的力学性能(特别是钢的强度)，研究了化学成分及固溶处理温度对其组织和性能的影响。结果表明，1000—1125℃固溶处理后，该钢的组织为单相奥氏体。在标准成分范围内，随着镍、锰含量的增加，该钢的强度降低，塑性有所改善。氮明显提高该钢的强度。根据试验结果，每增加0．01％的氮钢的室温强度可提高大约5MPa，且塑性基本上不受影响。当合金成分(质量分数，％)控制在C0．08—0．12、Crl6．5—17．5、Ni3．5—4．2、Mn8．0—9．0、N0．22—0．28时，1Crl7Mn9Ni4N钢经1050—1100℃固溶处理后强度较高、塑性好，室温强度σ0．2和σb可分别达到400MPa和800MPa。     

VN合金在大规格角钢生产中的应用研究

大规格角钢主要用于铁塔制造和建筑结构中。唐钢过去用16Mn钢生产Q345级别角钢，因供轧化学成分范围较窄，供轧率偏低。通过加入V-Fe合金及VN合金进行微合金化，设计了16Mnv(N)钢种生产角钢，使角钢综合性能有显著提高。分析比较了16Mn、16MnV及16MnV(N)角钢的性能，认为在大规格高强度角钢生产中，用VN合金进行微合金化，其效果是最佳的。     

Hydriding and Dehydriding Characteristics of Mechanically Alloyed LaMg_(17) Ni Composite Material

Magnesiumandmagnesiumalloyshavebeenin vestigatedashydrogenstoragematerialsforseveralde cadesbecausefarmorehydrogenbyweightcanbestoredinthemthaninmostoftheothercurrentlyknownhydrogenstoragealloys .Moreover ,thehighnaturalabundanceofMg ,itslightmassandenviron mentalcompatibilitypotentiallymakemagnesiumoneofthemostprospectivecandidatesforfuturehydrogenstoragematerials .Unfortunately ,thepracticalappli cationofMganditsalloyshasbeenlimitedonlytocertainstoragedevicebecauseoftheirpoorhydriding dehydr…     

Investigation of structural properties of ITO thin films deposited on different substrates

The influence of the substrate nature on the structure and morphology of ITO thin films grown by thermal evaporation in vacuum is investigated. The as-prepared metal films with Sn/In molar ratio of 0.1 were subsequently annealed for 2 h at 723 K in air (to obtain tin doped indium oxide), then annealed in vacuum at 523 K, followed by UV irradiation (to reduce the electrical resistivity). Irrespective of substrate nature, XRD data evidence a (222) preferential orientation in films. Substrate nature, annealing in vacuum and UV irradiation influence the structure, morphology, optical, electrical and surface wetting properties of the films' surface.     

Industrialization of High Performance Sintered NdFeB Magnets

Sintered Nd-Fe-B magnet was manufactured by advanced equipment via a SC (Strip casting) technology.It has integrative performance.     

纤维体积分数对K3D/MCPA复合材料力学性能的影响

本文研究了纤维体积分数对三维编织芳纶纤维增强铸性尼龙(简称K3D／MCPA)复合材料力学性能的影响。研究表明，K3D／MCPA复合材料有优异的抗冲击性能，冲击强度比三维编织芳纶纤维增强铸性尼龙(简称C3D／MCPA)和纯基体均有大幅度的提高，且随着纤维体积的提高而升高。K3D／MCPA复合材料剪切强度随纤维体积比的增大而增大，其纵向剪切强度低于纯基体和C3D／MCPA复合材料，但其横向剪切强度高于它们。K3D／MCPA复合材料弯曲强度与弯曲模量随纤维体积比的提高而提高，但与相同体积比的C3D／MCPA相比，K3D／MCPA的弯曲强度与弯曲模量均较低。     

可焊性高强度钢筋的开发与生产

为进一步开发国际钢材市场，研制开发了符合加拿大可焊性高强度钢筋标准要求的高强度钢筋．制定了化学成分及力学性能内控标准，分析了生产工艺各环节对成分和性能的影响，依据试验结果，在全面统计分析的基础上，调整了冶炼成分，生产的531批钢筋全部合格．通过直方图及回归分析，说明了制定的产品生产工艺可行，也为今后的生产提供了理论依据。     

油墨用聚氨酯胶粘剂的性能研究

主要研究用于印刷油墨的单组分溶剂型聚氨酯粘合剂，考查聚合物多元醇类型对树脂微观形态、机械性能以及印刷适应性和附着性等性能的影响。研究结果表明，聚酯型树脂的微相分离程度低于聚醚型，具有较好的机械性能、印刷适应性和附着性。     

Chemical compositions and optical properties of HfOxNy thin films at different substrate temperatures

High-k HfO_xN_y thin films have been grown by radio frequency (rf) reactive sputtering of metal Hf target in N₂/Ar/O₂ ambient at different substrate temperatures. The chemical compositions of the films have been investigated as a function of substrate temperature by X-ray photoelectron spectroscopy (XPS). XPS measurements showed that nitrogen concentration increases with an increase in substrate temperature. Room-temperature spectroscopic ellipsometry (SE) with photon energy 0.75–6.5 eV was used to investigate the optical properties of the films. SE results demonstrated that refractive index n increases with an increase in substrate temperature. Based on TL parameters which were obtained from the best fit results used in a simulation of the measured spectra, meanwhile, we conclude that the energy band gap (E_g) decreases with an increase in substrate temperature.