雷达仿真系统中电磁干扰环境的仿真设计和实施

雷达仿真系统是为检测雷达设备的抗干扰能力以及在各种电磁环境下的工作性能而设计的，包括有源干扰和无源干扰的模拟仿真。本文阐述了无源干扰即杂波的散射模型和仿真过程；从同步脉冲干扰的基本原理出发，阐明在雷达工作环境仿真系统中距离拖引、速度拖引、虚假目标等同步脉冲有源干扰的设计和实施过程；并针对工作在搜索和跟踪交替模式下的相控阵雷达提出自适应综合干扰方式；最后分析并总结了系统仿真时为真实、有效地模拟电磁干扰环境应注意的关键问题。     

建(构)筑物机械拆除方法综述

介绍了几种常用的建(构)筑物机械拆除方法,对其工作原理、特点、应用条件及局限性加以分析和说明。     

Powder Deposition in Three Parallel-Oriented Dies of Different Shapes

Uniformity of bulk density distribution during the die filling process is required to minimize quality problems, such as distortion and cracking, for powder compacts. Understanding the die filling process is necessary in ensuring a uniform powder deposition. The second-generation pressure deposition tester (PDT-II) was used to investigate the deposition process and final pressure distribution of powder filling in toroidal, cylindrical, and E-shaped dies. All tests were conducted using a spray-dried free-flowing granular powder. The results indicated that for toroidal dies: (1) the area around 0° orientation (the leeward end) had the highest pressure values (1186.7 to 2498.0 Pa), with the average pressure values of the remaining area 353.7-648.0 Pa; (2) the pressure distribution was symmetrical about the centerline parallel to the feed shoe movement direction; (3) the highest feed shoe speed (500 mm/s) led to the most nonuniform pressure distribution among the three speeds; (4) higher feed shoe speed did not always result in higher final pressure values; and (5) the right die tended to have higher final pressure values (215.0 to 2498.0 Pa) than the center die (95.4 to 2052.5 Pa). For E-shaped dies: (1) the final pressure values of the middle leg (308.9 to 760.7 Pa) were higher than those of the left and the right legs (148.9 to 530.3 Pa); (2) the area along the backside had the highest final pressure value (1054.6 to 1303.8 Pa); (3) the pressure distribution was symmetrical about the centerline parallel to the feed shoe movement direction; and (4) neither the center die nor the right die always had higher pressure values than the other one at all locations. Comparison between cylindrical and toroidal dies indicated that: (1) neither of the two die shapes (cylinder and toroid) led to consistently higher or lower final pressure values at all locations and (2) for all three feed shoe speeds, the toroidal die had higher average final pressure values in the 0° orientation.     

Pyrolysis of tertiarybutylphosphine at low pressure

The pyrolysis of tertiarybutylphosphine (TBP) has been studied in the low pressure conditions used for chemical beam epitaxy (CBE). The pyrolysis studies were carried out in low pressure reactors of two different configurations, one of which is a cracker cell designed for use in a CBE system. The reaction products were studied using a quadrupole mass spectrometer. The products observed are accounted for by a reaction mechanism involving homolysis of the parent TBP molecule to produce PH₂ and C₄H₉ radicals. These undergo subsequent reactions to form the stable products C₄H₈, PH₃ and H₂, with smaller amounts of P and P₂ being produced. The production of the sub-hydride PH₂ using this cracker cell design indicates that the use of partially cracked TBP may be a promising technique for reducing the amount of carbon incorporated into the growing epitaxial layer.     

Kinetic analysis for effect of initial substrate concentration on growth and secondary metabolite production in cultures of Nicotiana tabacum

Suspension cultures of tobacco cells were studied using airlift and rotary-drum bioreactors. The effect of initial concentrations of a major substrate, sucrose, on the growth and production of a secondary metabolite, phenolic compounds, was investigated. The dry weights and total concentrations of the phenolic compounds increased with the initial sucrose concentration in both bioreactors. Both bioreactors were found to have the same tendency for the effect of initial sucrose concentration. The structured model, presented previously was modified by considering that sucrose was hydrolyzed to glucose and fructose by an enzymatic reaction. The previous and the new models were applied to the above two sets of experimental data obtained with two bioreactors, independently. The hydrolysis of sucrose was elucidated to contribute slightly to the overall kinetics of growth and secondary metabolite production in these cultures. Furthermore, the levels of shear damage in each bioreactor were quantitatively compared based on the death rate constant, k_i, which is one of the model constants.     

Technique for Producing Mullite and Other Mixed-Oxide Systems

Mixed-oxide systems are of interest in a variety of technical ceramic applications. The key in many systems is to achieve a high degree of homogeneity, approaching the molecular level. A technique for producing mixed oxides via direct oxidation of mixtures of organometallic compounds is discussed as a potential route. Preliminary work performed on producing mullite is discussed.     

确定异常高压气藏地质储量和可采储量的新方法

基于文献[1]的定容，封闭，异常高压气藏的物质平衡方程式，提出了确定异常高压气藏原始地质储量，可采储量和采收率的新方法，通过实例的应用和对比表明，提供的新方法是适用的有效的。     

IC—V100电台锁相环频率合成器

本文从频率合成器的结构、功能入手,详细阐述了频率编程的原理及方法。     

Application of a Compaction Simulator to the Design of a High-Dose Tablet Formulation. Part I

The compaction properties of an investigational drug are studied by the use of a compaction simulator. The effects of punch velocity over the range of 30-640 mm^-1 on the compaction properties of the pure drug and a variety of formulas incorporating a high dose of the active compound have been investigated. The data were analyzed by applying the Heckel equation. The pure drug was found to have a high yield pressure at a relatively low punch velocity of 31 mm^-1. As the punch velocity was increased there was a decrease in crushing strength, primarily as a result of increasing yield pressure. These findings indicate that the pure drug predominantly consolidated by fragmentation and elastic deformation, with a slow plastically deforming component. The information obtained on the consolidation mechanism of the pure drug and, subsequently, on model formulas were instrumental in the design and selection of a robust formula and granulation process. The advantages of conducting dosage form design and characterization studies during the early phase of tablet formulation using means such as a compaction simulator are emphasized in this investigation.