高效液相色谱法分析混合甲基萘

建立了甲基萘的高效液相色谱分析方法，确定了紫外检测器波长、流动相及其组成等实验条件。结果表明：用高效液相色谱法分析混合甲基萘，α-甲基萘和β-甲基萘可以得到有效分离。     

甲基丙烯酸酯化反应动力学的研究

本文研究了甲基丙烯酸(MAA)和甲醇(MeOH)水溶液在硫酸存在下的酯化反应动力学。根据工业生产情况,选定反应物初始摩尔比为:MAA:MeOH:水=1:1.65:2,在温度为70～90℃,硫酸浓度为5％～15％(W/W)的范围内,考察了硫酸浓度、反应温度对酯化反应速度的影响,最后,提出了甲基丙烯酸酯化反应的动力学模型。     

UV‐radiation–induced preirradiation grafting of methyl methacrylate onto lignocellulose fiber in an aqueous medium and characterization

The preirradiation method of grafting has been established by ultraviolet radiation. Methyl methacrylate (MMA) was grafted onto jute fiber in an aqueous medium. The variation of graft weight with UV‐radiation time, monomer concentration, and reaction time was investigated. The conversion of monomer into homopolymer and graft copolymer was evaluated. The graft weight passes through a maximum value (～ 122%) with UV‐radiation time. The optimum value of the monomer concentration was evaluated for maximum degree of grafting. Graft copolymerization of MMA onto lignocellulose fiber significantly increases the elongation at break (～ 65%) compared to that of the “as‐received” sample. However, a linear decrease on breaking load was observed with the increase of graft weight. The estimation of degree of grafting was achieved using an IR technique by correlating band intensities with the degree of grafting. Considering the water‐absorption property, the grafted sample showed a maximum up to 61% decrease in hydrophilicity compared to that of the as‐received sample. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 1667–1675, 2004     

723型阳离子交换树脂催化合成甲基叔丁基醚

本文研究利用723型阳离子交换树脂催化合成MTBE，采用正交设计的统计方法，对影响产率的各因素如反应温度，反应时间，催化剂用量和原料摩尔比进行组合，找到合适的工艺路线，最佳反应条件为：催化剂用量为5g，甲醇与叔丁醇比为3：1，反应时间为7h。     

Ionic liquids as electrolytes

Salts having a low melting point are liquid at room temperature, or even below, and form a new class of liquids usually called room temperature ionic liquids (RTIL). Information about RTILs can be found in the literature with such key words as: room temperature molten salt, low-temperature molten salt, ambient-temperature molten salt, liquid organic salt or simply ionic liquid. Their physicochemical properties are the same as high temperature ionic liquids, but the practical aspects of their maintenance or handling are different enough to merit a distinction. The class of ionic liquids, based on tetraalkylammonium cation and chloroaluminate anion, has been extensively studied since late 1970s of the XX century, following the works of Osteryoung. Systematic research on the application of chloroaluminate ionic liquids as solvents was performed in 1980s. However, ionic liquids based on aluminium halides are moisture sensitive. During the last decade an increasing number of new ionic liquids have been prepared and used as solvents. The general aim of this paper was to review the physical and chemical properties of RTILs from the point of view of their possible application as electrolytes in electrochemical processes and devices. The following points are discussed: melting and freezing, conductivity, viscosity, temperature dependence of conductivity, transport and transference numbers, electrochemical stability, possible application in aluminium electroplating, lithium batteries and in electrochemical capacitors.     

Influence of composition and molecular mass on the morphology,crystallization and melting behaviour of poly(ethylene oxide)/poly(methyl methacrylate) blends

Results are reported on the influence of composition and molecular mass of components on the isothermal growth rate of spherulites, on the overall kinetic rate constant, on the primary nucleation and on the thermal behaviour of poly(ethylene oxide)/poly(methyl methacrylate) blends. The growth rate of PEO spherulites as well as the observed equilibrium melting temperatures decrease, for a given T_c or ΔT, with the increase of PMMA content.Such observations are interpreted by assuming that the polymers are compatible in the undercooled melt, at least in the range of crystallization temperatures investigated. Thermodynamic quantities such as the surface free energy of folding σ_e and the Flory-Huggins parameter χ₁₂ have been obtained by studying the dependence of the radial growth rate G and of the overall kinetic rate constant K from temperature and composition and the dependence of the equilibrium melting temperature depression ΔT_m upon composition, respectively.     

棉籽油间歇式酯交换反应动力学的研究

生物柴油(棉籽油甲酯)可以由棉籽油与甲醇在催化剂KOH存在下通过酯交换反应制得。故对棉籽油间歇式酯交换反应动力学进行了研究,并考察了反应温度和催化剂浓度对产物棉籽油甲酯浓度的影响。用液相色谱法分析棉籽油的组成;用气相色谱法分析产物中棉籽油甲酯的含量。由实验数据绘制的动力学曲线得到酯交换反应在开始阶段为准二级反应,以后紧接转为一级反应和零级反应,与文献报导的棕榈油酯交换反应动力学结果一致。由实验数据求出酯交换反应在开始阶段的动力学参数,35℃、45℃时的反应速率常数分别为0.9179Lmol-1min-1和1.049Lmol-1min-1,酯交换反应的活化能为10.88kJmol-1。根据实验结果得到棉籽油酯交换反应的最佳反应温度为45℃,最佳催化剂为1.1%KOH。     

SMAS/AM/淀粉抗温接枝共聚物的研究

研究了甲基丙烯磺酸钠(SMAS)、丙烯酰胺(AM)与淀粉接枝共聚物的合成方法，接枝反应的影响因素和热稳定性。实验结果表明，该接枝反应基本符合自由基反应的一般规律，并且其聚合产物具有明显的抗高温能力。     

气相酯交换法合成碳酸甲丙酯负载型催化剂的研究

考察了负载型金属氧化物催化剂对碳酸二甲酯和丙醇气相酯交换合成碳酸甲丙酯的催化性能,并采用BET、XRD、CO2-TPD方法对催化剂进行了表征.结果表明,TiO2/Al2O3对反应具有较高的催化活性和稳定性.随着TiO2负载量的增加,催化剂的比表面积减小,而催化性能则随Ti负载量的增加先增加后减小,在Ti负载量为5%(wt)时活性达到最高,当Ti负载量低于5%(wt)时,TiO2可能以非晶态形式分散在Al2O3表面,而当Ti负载量高于5%(wt)时,TiO2以微晶的形式存在.CO2-TPD研究表明,负载量的改变对催化剂的碱性影响不明显.     

Controlled destruction of residual crosslinker in a silicone elastomer for drug delivery

In drug delivery systems that use silicone elastomers as a diffusion matrix for the active drug, it is common to crosslink the material by the hydrosilylation reaction. In this platinum‐catalyzed reaction, vinyl groups on a polymer add to the methyl siloxane hydride (MHS) groups on a low molecular mass crosslinker. With an excess of crosslinker, a fast curing is achieved and a fully crosslinked material is formed. Unreacted MHS groups were shown to remain in the elastomer after curing because of the excess crosslinker. In this work, a simple procedure was developed to eliminate the unreacted MHS groups from the final product. We found that storage of the product at +40°C and 75% relative humidity for a few weeks will effectively destroy the residual MHS groups in the elastomer. The effects of varying levels of humidity, oxygen, and temperature on this postcuring procedure were studied. The amount of MHS groups was measured with NMR and IR spectroscopy. We also found that the hardness of the material increased by approximately 25% as a consequence of this postcuring treatment. This increase is probably due to a secondary crosslinking reaction between MHS and silanol groups. Heat treatment at higher temperatures led to an even further increase in the hardness and compression modulus. Because no MHS groups remained in the elastomer when this heat treatment was started, it is apparent that another secondary crosslinking reaction is occurring, probably silanol condensation. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 2254–2264, 2002