Damage mechanism at different transpassive potentials of solution-annealed 316 and 316l stainless steels

Electrochemical impedance spectroscopy (EIS), anodic polarization and scanning electron microscopy techniques were used to investigate the damage mechanism in the transpassive potential region of AISI ...     

Verhalten von Magnesiumlegierungen für Anwendungen im Fahrzeugbau bei mechanisch‐elektrochemischer Komplexbeanspruchung: Einfluss passivierender Deckschichten und Mechanismen der lokalen Schädigung

Behavior of Magnesium‐Alloys for Automotive Applications under Mechanical and Environmental Loading: Influence of Passivating Films and Mechanisms of Local Breakdown To assure an efficient design of components under cyclic loading, all available data concerning fatigue have to be observed. Therefore the influences of manufacturing on the material condition, the mechanical loads and environmental effects have to be analysed. Magnesium‐alloys are of special interest for lightweight applications because of their excellent strength‐density ratio. The corrosion resistance of magnesium‐alloys depends on the same factors that are critical to other metals. The alloys have a good stability to atmospheric exposure and a good resistance to attack by alkali, chromic and hydrofluoric acids. However, because of the electrochemical activity of magnesium, the relative importance of some factors is greatly amplified. The nature and composition of passive films formed on magnesium‐alloys depend on the prevailing conditions, viz. alloy‐composition, passivation potential, pH, electrolyte composition and temperature. Passive films may be damaged by local breakdown. Because of this, magnesium‐alloys suffer a degradation of their properties when exposed to an aqueous environment. The main topic of the present investigations is the verification of mechanisms of the local breakdown of the protecting film. At least two mechanisms are possible for this localization: mechanical breakdown by slip steps and electrochemical breakdown (for e.g. by the effects of chloride ions). Corrosion and passivation of different high purity alloys have been studied in different solutions (neutral, alkaline with specific anions and cations) using electrochemical techniques. The diecasted alloys were tested as produced and machined. The results clarified that depending on alloy/material and surface condition/corrosion environment different mechanisms for electrochemical breakdown of the protecting films are possible. Hence fatigue life under environmental loading is influenced by surface and testing conditions.     

6种金属材料在典型工业大气中的腐蚀规律

选取具有代表性的碳钢、不锈钢、镀锌碳钢、铝、钛和铜挂片,在某企业不同部位投放后进行为期半年的大气腐蚀试验,得出了在半年期中的腐蚀规律。在此基础上,对每种金属材料的腐蚀特点进行总结,并对大气腐蚀的各种影响因素进行分析,提出了行之有效的防护措施。     

含硫化氢气井钻井过程中的腐蚀因素与防护研究

在含硫气井的钻井过程中对于HRC大于22的钻具钢材除了腐蚀疲劳之外，在pH值小于9的环境中会发生硫化物应力腐蚀破裂，这种破坏比腐蚀疲劳更突然、更快，使钻杆大量损坏。含硫气井在钻井过程中，由于湿硫化氢的出现，常常会出现油管、套管、钻井设备、钻井仪器以及对支持保护管柱的水泥环柱等腐蚀和损坏问题，为此，阐述了湿硫化氢的腐蚀特点、机理，归纳总结了影响腐蚀的因素，综述了如何在这些方面防止其腐蚀，使损失减小，为指导油管、套管防腐工程实践提供了依据。建议在钻井过程中采用碱性钻井液，其pH值可到9或更高(至pH值12)，以减缓或防止钻井过程中电化学从硫化物应力腐蚀破裂；含硫气井用的钻杆应该间歇使用。钻杆停用堆置时间可使其放氢，使钻杆恢复韧性，防止硫化物应力腐蚀断裂。     

模糊层次分析法在腐蚀影响因素分析中的应用

结合国内外对碳钢CO2腐蚀影响因素的研究成果,采用模糊层次分析法对影响输油管道 CO2腐蚀的因素进行定量分析,明确界定出这些因素对二氧化碳腐蚀影响的相对重要性(权重),为后续制定经济有效的管道内腐蚀防护措施提供了客观依据。     

Intergranular corrosion of a light aircraft aluminum alloy propeller

Examination of the wreckage of a light aircraft revealed that approximately 20 cm was missing from one tip of the aluminum alloy propeller. Fractographic and metallographic examination of the remaining portion of the propeller revealed extensive grain-boundary separation in the vicinity of the fracture, and grain edges and corners rounded by corrosion on the fracture surface. Energy dispersive X-ray analysis (EDXA) revealed fluorine on, and in the vicinity of, the fracture surface. In the ensuing litigation, it was asserted that the crash occurred because the propeller fractured in flight as the result of intergranular attack caused by the use of a fluorine-bearing cleaner.     

泡沫夹克管的防水与保温

针对辽河油田应用泡沫夹克管道的情况，从泡沫夹克管的制作和敷设施工直到设计等环节，结合泡沫夹克管防腐保温的机理，并从理论与实践相结合角度出发，提出导致泡沫夹克管腐蚀损坏的最主要原因是管道保温层漏水，进而提出了在设计和施工过程中提高泡沫夹克管质量的措施。