Evidence of late palaeozoic thermalwater metallization in South Yongmei Depression

This paper discusses the seafloor thermalwater spout sedimentary activity in South Yongmei Depression according to the following evidences: the Yongmei region was in an extended tectonic environment of metaplateform and locally developed intracontinental rift aulacogen in company with the activity of rich alkali, high potassium volcanics of double-peak type. Several kinds of hydrothermal sedimentary rocks and the ore-bearing sedimentary formations of copper-polymetals, iron and manganese exist in this region with a zoning feature of the seafloor thermalwater spout sedimentation. Project supported by the Science Foundation of NECC for Returns Synopsis of the first author Wu Chengjian, associated professor, born in 1957, majoring in ore deposit and mineralgraphy.     

�����������ɺͼӹ��е�һЩ��������

本文简要介绍了国外在开发超酸性气体过程中遇到的材料选择、腐蚀监测、水化物堵塞、超酸性气的处理和加工等问题所采取的措施和办法。     

二钼酸铵(ADM)非团聚晶体的生成试验

探讨了二钼酸铵非团聚晶体生成的机理及制取新工艺。采取该工艺制取的ADM费氏粒度（Fsss)约30μm，激光粒度分布d0.5为370μm，松装比达1.37/cm^3。     

Cu－Zn－Al合金中贝氏体的有序性

本文用Ｘ射线研究了Ｃｕ－２０Ｚｎ－６Ａｌ（ｗｔ％）合金中贝氏体结构的有序性，并与马氏体结构进行了比较，实验表明，从高温Ｂ２母相和低温Ｌ２１母相生成的贝氏体中（１１５）和（２０５）衍射峰或（１２１０）和（２０１０）衍射峰是重叠的，对生成的贝氏体进行一段时间的保温或缓慢冷却处理，其衍射峰的特征并不改变，这与马氏体（１１５）和（２０５）衍射峰或（１２１０）和（２０１０）衍射峰的分离特性不相符合。说明贝氏体结构有序度与马氏体明显不同，它的形成不可能继承母相的有序度。     

机械研磨 Ni_(50)B_(50)合金形成非晶的过程

本文研究了机械研磨 Ni_(50)B_(50)合金非晶的形成过程。唯象地提出用 J-M-A 方程描述此过程,并作了简单的讨论。     

用屏蔽暂堵技术封堵水平井裂缝性漏层

克拉玛依油田HW702水平井的大斜度段和水平段,将穿越纵向裂缝发育的二叠系佳木河组储层。为安全钻进和保护油层,用超细碳酸钙和磺化沥青复配后加入复合离子钻井液中成屏蔽暂堵的堵漏钻井液。室内用岩心试验,屏蔽暂堵后渗透率可降为0,暂堵深度小于3cm,可用酸化和射孔解堵。现场使用效果也很好,使HW702水平井顺利完钻,并获得工业油气流。     

油基钻井液的推广及循环利用

针对普通水基钻井液在钻进中强、强水敏性油藏时会造成储层污染、产量降低的问题,指出了油基钻井液在钻进该类油藏时的优势和其成本高、对生态环境有污染的缺点。为了大面积推广应用油基钻井液,重点介绍了油基钻井液的特性和稳定性影响因素,并通过室内评价证明了油基钻井液在油层保护中的良好效果,着重阐述了油基钻井液在王庄油田的现场应用情况,并探讨了油基钻井液的循环利用技术。研究结果表明,油基钻井液不仅具有良好的油层保护效果,而且具有较好的社会经济效益。     

Microcalorimetry for characterization of film formation and cure of coatings and adhesives

A new microcalorimeter with eight parallel channels using robust, low cost sensors for characterization of coatings and adhesives is described and first experiments on coatings and adhesives are presented. The calorimetric sensors are based on thin glass plates (20 mm × 20 mm, thickness 150 μm) with heater and thermocouple sputtered on the surfaces (calorimetric active area of about 9 mm²). The setup allows heating and cooling experiments as well as isothermal measurements in the temperature-modulated mode with up to eight sensors in parallel. The measured quantities are the real (C^′_p) and imaginary part (C^″_p) of the complex heat capacity (), the related absolute value of the heat capacity () and the heat flow . An industrial computer (NI PXI system) with specific software for calibration and data recording controls the electronic components. Sensors can be embedded in a temperature controlled oven (heating and cooling by Peltier elements) or alternatively in a climatic cabinet with controlled temperature and humidity.

The method has been applied successfully to monitoring of film formation of aqueous polymer dispersions (styrene-acrylate copolymer) and curing of coatings.     

Methane/natural gas storage and delivered capacity for activated carbons in dry and wet conditions

Methane/natural gas storage and delivered capacity for three different activated carbons in dry and wet conditions were measured. In all tests the temperature of the bed was maintained constant at 277.15 K and pressure was increased up to 10 MPa. Natural gas storage capacity was less than methane storage capacity in dry conditions for all the three activated carbons tested, while the gas delivery was almost the same. One of activated carbon tested (NC120) showed the possibility of hydrate forming for pressures higher than 4 MPa but the amount of gas stored still was less than the amount stored in dry conditions over the whole range of pressure. The analysis of the gas delivered at each pressure steps shows that considerable amount of heavy components do not come out from the bed even at very low pressures in both dry and wet condition tests. Repeatability of the sorption/desorption processes - vital for possible commercial/industrial use - has been examined over various cycles.     

On modeling the design of cellular manufacturing systems

A new optimization model is discussed for the design of cellular manufacturing systems. It is based on an integer programming formulation that updates some other models by eliminating redundant machine assignment and cost coefficients dependent on cell configuration. To reduce computational burdens, a simplified integer programming model and a decomposition algorithm are proposed. Several computer solutions were performed to evaluate the performance of the new model. The computational results are discussed.