高温预析出对Al-Zn-Mg系铝合金时效硬化和应力腐蚀的影响

研究了高温固溶后降温处理工艺对中强可使预析出LC52和7039铝合金的组织、时效硬化和应力腐蚀的影响。金相观察发现,高温预析出可优先在晶界处产生,并提高随后时效状态下晶界析出相的不连续分布程度,温度降低到一定程度晶内和晶界产生大量析出。合金拉伸性能和应力腐蚀结果表明,预析出在保持强度和塑性的同时,可提高抗应力腐蚀性能。而预析出温度降低,合金强度呈下降趋势。     

场激活加压燃烧合成WC-Ni复合材料的工艺参数研究

以钨、碳和镍为原料,在电场激活下,材料的燃烧合成和致密化同时进行,短时间内完成了碳化钨镍复合材料的制备。研究了场激活 加压燃烧合成中的工艺参数,如脉冲电流、能量控制模式、升温速率、最高温度和压力对反应的影响。测量了在反应合成和致密化前后的样品 收缩率。所制备的复合材料的相对密度,490N载荷下Vickers硬度和断裂韧性分别为99.2%,13.965GPa和5.9MP·m1/2。     

基于双因子认证技术的网络身份识别

本文提出了一种基于动态双因子认证技术的网络身份识别方法,用户每次登录的口令是利用系统时间和用户ID通过MD5加密算法计算得到,其通过MD5加密后生成的登录口令是随机的,这将进一步提高开放网络环境下身份识别的可靠性和安全性。同时,本文还提出网络身份识别技术可以应用到各类网站的服务器上,用来完成对用户身份的识别,以提高网络系统的安全性。     

Corrosion Inhibition Mechanism with Spilt Cell Technique of Rare Earth Metal on LC4 Al Alloy

A new method of studying the corrosion inhibition mechanism of rare earth metal(REM) on LC4 Al alloy with the spilt cell technique was studied. The principle and experimental method of the spilt cell technique were analyzed. By measuring the change of net-electric current between the two electrodes caused by the change of the amount of oxygen in the solution and the addition of CeCl₃, the influence of corrosive performance of CeCl₃ on LC4 super-power aluminum alloy in the 0.1 mol·L⁻¹ NaCl solution was investigated. Meanwhile, the conditional changes of pH values, CeCl₃ solution, additire and time of performance were also studied. Finally, the features of electrode surface were revealed by using SEM and X-ray energy-dispersive spectrometry (EDS). By combining these with other electric chemical techniques, such as potential-time curve, polarization curve et al.     

熔融碳酸盐燃料电池阴极材料的导电性

通过交流阻抗方法研究了熔融碳酸盐燃料电池阴极材料锂镍氧化物、锂钴氧化物和锂铁氧化物的导电性能。结果表明:锂镍氧化物电极的导电性最好,锂钴氧化物电极的导电性次之,锂铁氧化物电极的导电性最差;它们的导电性都随着温度的升高而按指数规律增加;在合成锂钴氧化物(或锂铁氧化物)的过程中,使Li2CO3轻微过量,可以提高锂钴氧化物(或锂铁氧化物)电极的导电性,而且在同一温度下,随着nLi∶nCo(或nLi∶nFe,摩尔比)值的增大,锂钴氧化物(或锂铁氧化物)电极的导电性显著增加。     

利用铝（100）面隧道孔制备纳米模板及有序阵列材料

高纯铝箔通常通过电化学扩面后用作铝电解电容器的阳极材料。利用铝箔（100）面隧道孔制备纳米模板。这种纳米模板的特点是制作简单、模板面积大，纳米阵列材料形状可控性强。还利用两步电化学侵蚀铝箔的特殊工艺，研制出纵横交错的TiO2纳米有序阵列材料。     

对河南铝工业发展的几点建议

从全国及河南省铝工业的发展现状入手，分析了河南铝工业的优势及发展中存在的不足。阐述了发展河南铝工业应把握的几个主要问题，并提出了自己的建议和看法。     

Formation of composites fabricated by exothermic dispersion reaction in A1-TiO2-B2O3 system

The formation of aluminum matrix composites fabricated by exothermic dispersion reaction in A1-TiO2-B2O3 system was investigated. The thermal analysis results show that the reactions are spontaneous and exothermic. The Gibbs free energy of α-Al2O3 is the lowest among all the combustion products, followed by TiB2 and Al3Ti. It is noted that when the B2O3/TiO2 mole ratio is below 1, the reaction products are composed of particle-like α-Al2O3, TiB2 and rod-like Al3Ti. The α-Al2O3 crystallites, resulting from the reaction between A1 and TiO2 or B2O3, are segregated at the grain boundaries due to a lower wettability with the matrix. SEM micrographs show that rod-like Al3Ti phase distributes uniformly in the matrix. When the BEO3/TiO2 mole ratio is around 1, the Al3Ti phase almost disappears in the composites, and the distribution of α-Al2O3 particulates is improved evidently.     

单层开采的圆形定压边界两层油藏压力动态分析

为更好地分析具有越流的多层油藏的压力动态，采用有效井径的概念，在半透壁模型的基础上建立了圆形定压边界、两层越流油藏单层开采时的渗流数学模型。通过拉氏变换得到了拉氏空间中以Bessel函数表示的精确解。数值反演计算结果表明，单层开采的两层油藏与全部打开的两层油藏的压力动态基本相同，都表现为3个阶段：早期是介于两个渗透层之间的均质流动；中间为过渡段，导数曲线出现下凹特征；晚期表现为整个油藏的均质特征。随着边界距离的增加，压力导数值趋近于0．5。半透率越大过渡段出现得越早。导数曲线下凹程度越小；储容比越大导数曲线峰值越小，导数曲线下凹程度越小；随着两层渗透率比值变小。过渡段变短，导数曲线下凹程度变小。图1参9     

Note on ‘Construction of Double Sampling s‐Control Charts for Agile Manufacturing’

He and Grigoryan (Quality and Reliability Engineering International 2002; 18 :343–355) formulated the design of a double‐sampling (DS) s control chart as an optimization problem and solved it with a genetic algorithm. They concluded that the DS s control charts can be a more economically preferable alternative in detecting small shifts than traditional s control charts. We explain that, since they only considered the average sample size when the process is in control, their conclusion is questionable. Copyright © 2006 John Wiley & Sons, Ltd.