A unified proposal for characteristic testing methods and figure of merit of 8‐kV/3.5‐kVA class light‐triggered thyristors

Power devices with high capability have been developed. 8‐kV/3.5‐kA‐class light‐triggered thyristors have the highest capability among power devices. These devices are used in the Kii Channel HVDC transmission system in Japan. In this paper, we report the extracted problems of conventional testing methods of 8‐kV/3.5‐kA‐class light‐triggered thyristors among manufacturers, and the proposed unified testing methods on the basis of element characteristics and operating conditions in the Kii Channel HVDC system. Furthermore, we propose a figure of merit for power devices for the practical use, and try to extract elements used at the Kii Channel HVDC system with small margins and low withstand capabilities. © 2002 Wiley Periodicals, Inc. Electr Eng Jpn, 140(3): 61–70, 2002; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.10024     

Quantitative evaluation of generator power control effect of FACTS controllers for power system stabilization

The advancement of power electronics technologies has significantly developed the power system stabilizing controllers. Quantitative as well as qualitative evaluation of their effectiveness in power systems is a matter of great importance for the feasibility investigation of these apparatus. In this paper, the possible control region of FACTS controllers with series and/or shunt configuration in a single machine to infinite bus system is formulated in the powerangle curve with a set of algebraic equations. The effectiveness of TCPST (Thyristor‐Controlled Phase Shifting Transformer), SSSC (Static Synchronous Series Compensator), and TCSC (Thyristor‐Controlled Series Compensator) for the improvement of the transient stability is evaluated quantitatively as a numerical example. The correctness of the proposed method has been confirmed by analysis based on the electromagnetic transients simulation with a detailed system model. © 2001 Scripta Technica, Electr Eng Jpn, 138(3): 43–51, 2002     

Sensorless control of synchronous reluctance motors using on‐line parameter identification method not affected by position estimation accuracy

This paper presents a novel on‐line parameter identification method for sensorless control of Synchronous Reluctance Motors (SynRMs). Although conventional sensorless control methods based on mathematical models usually need some complex measurements of motor parameters in advance, the proposed identification method does not require them and can be realized on‐line. The proposed method identifies motor parameters under sensorless control, so rotor position and velocity cannot be used to identify these parameters. However, the proposed method does not need rotor position and velocity, and identified parameters are not affected by these estimation errors. The sensorless control using identified motor parameters is realized, and the effectiveness of the proposed method is verified by experimental results. © 2006 Wiley Periodicals, Inc. Electr Eng Jpn, 155(3): 62–69, 2006; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20258     

A novel method of suppressing the inrush current of transformers by using a series‐connected voltage‐source PWM converter

This paper proposes a novel method of suppressing the inrush current of transformers. A small‐rated voltage‐source PWM converter is connected in series to the transformers through a matching transformer. As the connected PWM converter serves as a resistor for the source current, no inrush phenomena occurs. The required rating of the PWM converter, which serves as the damping resistor for the inrush phenomena, is 1/400 that of the main transformers in single‐phase circuits. In three‐phase circuits, it is 1/900. The basic principle of the proposed method is discussed. Digital computer simulation is implemented to confirm the validity and excellent practicability of the proposed method using the PSCAD/EMTDC. A prototype experimental model is constructed and tested. The experimental results demonstrate that the proposed method can perfectly suppress the inrush phenomena. © 2006 Wiley Periodicals, Inc. Electr Eng Jpn, 157(4): 56–65, 2006; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20174     

A novel robust current control approach using adaptive line enhancer for three‐phase current‐source active power filter

An effective system control method is presented for applying a three‐phase current‐source PWM converter with a deadbeat controller to active power filters (APFs). In the shunt‐type configuration, the APF is controlled such that the current drawn by the APF from the utility is equal to the current harmonics and reactive current required for the load. To attain the time‐optimal response of the APF supply current, a two‐dimensional deadbeat control scheme is applied to APF current control. Furthermore, in order to cancel both the delay in the two‐dimensional deadbeat control scheme and the delay in DSP control strategy, an Adaptive Line Enhancer (ALE) is introduced in order to predict the desired value three sampling periods ahead. ALE has another function of bringing robustness to the deadbeat control system. Due to the ALE, settling time is made short in a transient state. On the other hand, total harmonic distortion (THD) of source currents can be minimized compared to the case where ideal identification of the controlled system can be made. The experimental results obtained from the DSP‐based APF are also reported. The compensating ability of this APF is very high in accuracy and responsiveness although the modulation frequency is rather low. © 2004 Wiley Periodicals, Inc. Electr Eng Jpn, 150(1): 50–61, 2005; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20014     

Neutron Stress Measurement of W‐Fiber Reinforced Cu Composite

Stress measurement methods using neutron and X‐ray diffraction were examined by comparing the surface stresses with internal stresses in the continuous tungsten‐fiber reinforced copper‐matrix composite. Surface stresses were measured by X‐ray stress measurement with the sin²ψ method. Furthermore, the sin²ψ method and the most common triaxal measurement method using Hooke's equation were employed for internal stress measurement by neutron diffraction. On the other hand, microstress distributions developed by the difference in the thermal expansion coefficients between these two phases were calculated by FEM. The weighted average strains and stresses were compared with the experimental results. The FEM results agreed with the experimental results qualitatively and confirmed the importance of the triaxial stress analysis in the neutron stress measurement.     

Prebiotic synthesis of sequential peptides on the Hadean beach by a molecular engine working with nitrogen oxides as energy sources

Addressing the still open question of the prebiotic origin of sequential macromolecules (peptides, nucleic acids) on the primitive Earth, we describe a molecular engine (the primary pump), which works at ambient temperature and continuously generates, elongates and complexifies sequential peptides. This new scenario is based on a cyclic reaction sequence, whose keystep is the activation of amino acids into their N‐carboxyanhydrides (NCA) through nitrosation by NOx. This process could have taken place on tidal beaches; it requires a buffered ocean, emerged land and a nitrosating atmosphere. With the help of geochemical studies and computer simulations of atmosphere photochemistry, we show that the primitive Earth during the Hadean may have satisfied all these requirements. © 2001 Society of Chemical Industry.     

Cationic ring-opening polymerization of hexamethylcyclodisilazane: General aspects and tentative mechanisms

The ring-opening polymerization of hexamethylcyclodisilazane (D_2NMe), initiated by methyl triflate in 1,2-dichloroethane, forms in the first, fast kinetic step both linear polymer and cyclic dimer (D_4NMe). Subsequently a slow depolymerization process occurs leading to exclusively cyclotrisilazane (D_3NMe). On the basis of kinetic measurements carried out using an adiabatic calorimetric technique and complementary experiments, mechanisms of both propagation, cyclization and back-biting reactions are proposed. The influence of the reaction temperature was also studied; it is demonstrated that, at low temperature, polymerization does not lead to cyclic oligomer formation. In such conditions, the polymerization presents a ‘living’ character.     

High‐Tech‐Cellulose‐Funktionspolymere nach dem ALCERU®‐Verfahren

Functional High‐Tech‐Cellulose materials by the ALCERU® process Cellulose is one of the eldest materials of mankind. While the use of cellulose in former times was focused on application as a more construction or as a more textile material at present time the application profile turns to a more functional material using the ALCERU® process. Shaping of pure cellulose dissolution in NMMNO permits the manufacturing of materials for upholstery, filtration or biodegradable film strips having an uniform cross section. Fibreds, which can be applied in several packaging materials, are available using different techniques for regeneration cellulose. A great field of innovative functional cellulose materials is opened up by addition of several functional additives to cellulose dissolution. In this way piezo‐electrical conductive cellulose fibres (PZT) or high‐temperature filtration membranes are to be generated if one adds special types of ceramic powders. Above all PZT green fibres are applied in more recent uses as sensors or actuators. Electrically conductive cellulose fibres or filaments, which can be also used in the textile chain, can be prepared adding conductive carbon black to a cellulose dope on the same way, too. Cellulose material having adapted conductivity to different application is available by adding an exact defined amount of carbon black to cellulose dissolution. Finally cellulose beads can be manufactured by means of varied shaping technique. The beads are showing variable particle sizes and narrow pore size distribution. These properties open up very interesting application in the field of human blood purification or chromatography.