γ 射线引发 VAc 乳液聚合以制备白乳胶的动力学及工艺条件研究

研究了ＶＡｃ的辐射乳液聚合动力学，并对其聚合工艺条件作了初步探索。得出ＶＡｃ乳液在进行辐射聚合时，成核期结束较早（转化率在１０％以下），有相当长的恒速期存在。乳胶粒子直径在０．５～３μｍ之间，比一般的乳液聚合乳胶粒子要大。同时从动力学数据还可以看出几种成核机理（胶束成核，水相成核和液滴成核）同时存在，由此对试验条件提出了相应的要求。     

FTIR investigation of ethylene coordination and polymerization on reduced Cr/SiO2 catalyst

FTIR spectroscopy was applied to study the initial steps of ethylene polymerization on reduced chromia-silica (0.5 wt% Cr/SiO₂). To decrease the speed of the reaction small doses of gas were introduced to the catalyst in each run and C₂D₄ was used to confirm band assignments. At the initial steps of the reaction only ethylene molecules coordinated to probably Cr _A ²⁺ cations were observed. The concentration of such complexes was estimated to be about 50% of the total amount of Cr atoms in the sample. The FTIR spectrum of the polymer formed at the initial doses of C₂H₄ (when [C₂H₄] [Cr]) was found to be slightly different from that formed after excess ethylene was introduced onto the catalyst ([C₂H₄] > [Cr]).     

国产气相聚乙烯浆液催化剂的工业应用

本文简要阐述了北化院BCS01和上海院SLC-S两种国产气相聚乙烯浆液催化剂的性能、催化剂结构,在Unipol聚乙烯工业装置上应用结果,以及和进口同类催化剂UCAT-J的性能比较。     

Properties of poly(n‐butyl methacrylate) prepared by reverse atom transfer radical polymerization in an aqueous dispersed system

Reverse atom transfer radical polymerization (ATRP) of n‐butyl methacrylate (BMA) in waterborne media using Cu(II) complexes with azo initiators (i.e., reverse ATRP) was conducted. The influence of several factors, such as surfactant, catalyst, and reaction time, on the stability of the emulsion, the particle size, the morphology of the emulsion particles, and the control of the polymerization was investigated. The results showed great differences between ATRP and conventional emulsion polymerization, especially the nucleation mechanism and the kinetics. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 1542–1547, 2003     

High solids content emulsions. III. Synthesis of concentrated latices by classic emulsion polymerization

Two different methods of producing bi‐ and trimodal latices of a mixture of methyl methacrylate, butyl acrylate, and small amounts of acrylic acid were tested. It is shown that a combination of concentrating blends of seed particles by semibatch reaction, followed by a nucleation of small particles plus a second semibatch phase allowed us to obtain stable latices with solids contents over 65% and viscosities of below 2500 mPa s^?1 with little coagulum formation. The key parameter in determining latex stability, coagulum formation, and viscosity appears to be the the particle size distribution, and especially its modification attributed to secondary nucleation. Because it is not possible to eliminate water‐soluble monomers from the polymerization recipe, secondary (homogeneous) nucleation must be minimized by careful addition of the free‐radical initiator and choice of monomer feed flow rates. The nucleation of the third population in the trimodal latices is best accomplished with a mixed surfactant system because renucleation by anionic surfactant alone leads to detrimental changes in the particle size distribution (PSD) resulting from excessive flocculation of particles. In addition, it was found that the viscosity of the final products was not sensitive to small changes in the ionic strength of the latex, although neutralization to a pH of 6 effectively doubles the final latex viscosity. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 1916–1934, 2002; DOI 10.1002/app.10513     

An evaluation of commercial nickel catalysts during hydrogenation of soybean oil

The activities of several commercial nickel catalysts were determined by measuring their activation energies. Among these catalysts, G95E, Resan 22, Nysosel 222 and 325, all with low activation energy, were more active than DM3 and G95H, which had higher activation energy. However, the less active catalysts increased the linoleate selectivity of soybean oil during hydrogenation. The yields of bothtrans isomers and winterized oil were higher for the more selectively hydrogenated oil catalyzed by the less active catalysts. In the sensory evaluation, the fractionated solid fat that contained moretrans isomers was lower in flavor scores than the fractionated liquid oil after hydrogenation and winterization of soybean oil.     

New catalyst systems for the polymerization of acetylene

The catalytic activities of WCI₆Ph₄Sn, MoCl₅Ph₄Sn and tetrabenzyltitanium were examined in the polymerization of acetylene. The structure, morphology and electrical conductivity of the doped and non doped polyacetylene were also studied.     

Poly(butylene terephthalate)/organoclay nanocomposites prepared by in situ interlayer polymerization and its fiber (II)

Intercalated nanocomposites with poly(butylene terephthalate) (PBT) incorporated between the montmorillonite layers were synthesized from dimethyl terephthalate and 1,4-butane diol by using an in situ interlayer polymerization. The PBT nanocomposites were melt-spun at different organoclay contents to produce monofilaments. The samples were characterized by using wide angle X-ray diffraction, electron microscopy, thermal analysis, and tensile testing. The extent of the clay layer in the PBT was confirmed by using X-ray diffraction and electron microscopy, and the clay layer was found to be highly dispersed on a nanometer scale. The addition of only a small amount of organoclay was enough to improve the thermo-mechanical properties of the PBT hybrid fibers. The hybrids were extruded with various draw ratios (DRs) to examine the tensile mechanical property of the fibers. At DR=1, the ultimate tensile strength of the hybrid fibers increased with the addition of clay up to a critical content and then decreased. However, the initial modulus monotonically increased with increasing amount of organoclay in the PBT matrix. When the DR was increased from 1 to 6, for example, the strength and the initial modulus values of the hybrids containing 3 wt% organoclay decreased linearly.     

悬浮法合成聚丙烯腈高吸水性树脂

以偶氮二异丁腈为引发剂，用悬浮聚合法合成了交联聚丙烯腈，然后对其进行水解，得到了高吸水性聚丙烯腈。交联剂用量和水解条件对树脂吸水倍数的影响很大。树脂吸去离子水倍数为420倍，平均粒径为250μm。     

Olefins polymerization on titania and titania-supported rhodium

The adsorption of ethene and propene on titania and titania-supported rhodium has been studied, observing a continuous adsorption even after 24 h. The samples have been reduced at 623 or 773 K, but no difference was observed, whichever the reduction temperature or the presence of rhodium, on the amount of gas adsorbed per unit of surface area of the solid. A study of the polymerization has been done following the equal reactivity hypothesis, and it has been concluded that the role played by the rhodium particles is to facilitate adsorption of the gaseous molecule, that is then transfered to the surface of the support, where it polymerizes.