地下水运动数值模拟过程中边界条件问题探讨

本文对地下水运动数值模拟过程中边界条件的涵义 和处理方法进行了分析和讨论。阐述了边界条件所包含的双重意义。指出随着人类活动影响 强度的日益增大，边界条件的处理要面临一些新的更为复杂的问题。在模型预报之前必须首 先对边界条件做出预报。边界条件的预报既要考虑自然因素的作用，同时也要考虑人类活动 (人工开采和人工补给)的影响及由于邻区水流条件变化而产生的耦合效应。之后，给出了两 个应用实例。     

Efficient and accurate approach for powder compaction problems

 In this paper, a new approach for powder cold compaction simulations is presented. A density-dependent plastic model within the framework of finite strain multiplicative hyperelastoplasticity is used to describe the highly nonlinear material behaviour; the Coulomb dry friction model is used to capture friction effects at die-powder contact; and an Arbitrary Lagrangian–Eulerian (ALE) formulation is used to avoid the (usual) excessive distortion of Lagrangian meshes caused by large mass fluxes. Several representative examples, involving structured and unstructured meshes are simulated. The results obtained agree with the experimental data and other numerical results reported in the literature. It is shown that, contrary to other Lagrangian and adaptive h-remeshing approaches recently reported for this type of problems, the present approach verifies the mass conservation principle with very low relative errors (less than 1% in all ALE examples and exactly in the pure Lagrangian examples). Moreover, thanks to the use of an ALE formulation and in contrast with other simulations, the presented density distributions do not present spurious oscillations. Received: 20 March 2002 / Accepted: 15 October 2002 The partial financial support of the Ministerio de Ciencia y Tecnología (grant number DPI 2001-2204) is gratefully acknowledged.     

铝型材推弯工艺

通过铝型材圆环的推弯实验,研究了推弯工艺原理、变形过程,结合有限元模拟得到了和实验结果相吻合的型材厚度分布、成形零件卸载回弹后的曲率半径及型材截面畸变.结果表明:推弯零件曲率及截面畸变一致性高,成形模具结构简单且便于调整,数值模拟可以用于推弯工艺的优化分析.     

管壳式换热器流场三维数值模拟

采用多孔介质方法 ,在PHOENICS 3 3程序的基础上建立了换热器的三维流动计算模型。引入体积穿透率、表面穿透率、分布阻力等来描述换热器内的管束。模型通过计算Halle等[1] 的实验工况来进行验证 ,并尝试用于计算 2 0 0MW低温供热堆主换热器内的流场     

基于多智能体的数控机床资源共享技术研究

以数控铣床为对象，应用多智能体技术，以解决传统的资源共享所面lI缶的透明度低和效率低下的问题。首先，在分析功能模型的基础上，提出并实现了资源共享的四层网络拓扑结构；其次，构造了面向设备资源共享功能的智能体信息流模型，以实现四层结构之间的交互；其三，定义了智能体状态函数，并以此为依据，建立了智能体协商机制。所开发的原型系统表明，以上成果有效地提高了数控机床资源共享的透明度和效率。     

挟沙水流中沙粒对底壁湍流猝发的影响

本文在常规的边界层方程中保留了法向压力梯度项和增加了固粒对流体的使用项，结合Ｂａｔｃｈｅｏｌｒ对交界面提供的分析方法和小扰动稳定性理论，由理论分析和计算得到了包括沙粒之类的悬浮体的尺寸，比重，流动Ｒｅ数，两相速度差以及扰动波数与水流底壁湍流猝发角的关系，计算结果与Ｒａｓｈｉｄｉ等的实验结果相符。文中所得结果有助于进一步了解江河底部水流的流动特性以及泥沙的沉积和输运机理。     

A BOUNDARY INTEGRAL EQUATION AND ITS NUMERICAL SOLUTION OF POTENTIAL FLOW AROUND SURFACE-IRREGULA-RITIES

In this paper,using complex functional theory,the authors turn the potentialflow around the surface irregularities in a pressure conduit and semi-infinite platforms intoDirichlet problem.Based on Schwarz formula and by the application of Plemelj's formula,theauthors change the problem into the integration of a Cauchy boundary integral equation in theflow plane through the substitution of variables.Using numerical integration,the authors obtainthe velocity distribution and pressure coefficient along surface irregularities and platforms.Thephysical concept of this method is clear,the convergent speed is rapid and the computative effi-ciency is high.The calculated values agree well with the measured results.It is an effective andsimple method in solving potential flow.     

NUMERICAL SIMULATION OF STRATIFIED FLOW WITH BOTH VERTICAL TEMPERATURE GRADIENT AND VERTICAL SALINITY GRADIENT

Density stratified flow with both the vertical temperature gradient and the verti-cal salinity gradient is simulated numerically, in which turbulent terms are calculated by a sim-plified turbulence stress/flux algebraic model. The feature of stratification and turbulence is de-scribed correctly by the model. The computational results agree well with the experimental data.However, the k-e turbulence model is not so successful.     

Two dimensional deformation characteristics of bloom CC with liquid core reduction

A two-dimensional model was applied to simulate the liquid core reduction(LCR) technology of bloom CC using ANSYS software.The deformation characteristics of bloom under different liquid fraction and reducing amount are obtained.The results indicate that the main deformation condition of bloom shell is compressive strain,mainly undertaken by the liquid core,which increases with the enhancement of reducing amount.Solidified shell takes minor deformation.The longitudinal section of bloom appears sunken and the narrow side bulges,which grow serious when the liquid fractionincreases.     

2006年SEG年会反映的各向异性研究新进展

介绍了2006年SEG年会上所反映的各向异性研究的新进展，主要包括：提高速度分析精度的各向异性速度分析参数正交化方法；影响裂隙储层预测的地震波动力学与运动学特征差异分析；验证现行裂隙硬币理论模型可靠性的不规则裂隙有效弹性参数计算分析；提高计算效率的波场延拓各向异性参数参考值优选Lloyd算法；常见TTI介质不同成像方法试验效果的比较。