三峡地下电站变顶高尾水洞水动力特性

在国内首次应用模型水轮发电机组对三峡地下电站变顶高尾水洞方案进行水力过渡过程试验研究。对水轮机导叶实行分段关闭 ,并求出了二段关闭的最佳拐点 ,试验证实了二段关闭对减小尾水管进口的负压和机组转速上升有明显的作用。通过有关水力参数的测试 ,认为变顶高尾水洞可以满足各项技术要求 ,是一个减少山体开挖、节省投资的新型设计方案。在地下电站中具有广泛的应用前景     

马家河水电站的设计

马家河水电站通过在马家河和毛家河上游分别建底栏栅坝和低拱坝 ,经各自的引水系统将水引至两河口汇合流入前池发电。本文介绍了电站的开发方案 ,厂区、引水工程和取水枢纽的布置和设计     

Modeling of Energy Density Distribution in Rock Mass on the Basis of Seismotectonic and Geodetic Data

Using the focal mechanisms of earthquakes taken place from 1950 to 1996, the type and direction of principal strains were established, which made it possible to determine the volume stress-strain state of the south-east flank of the Baikal rift zone on the basis of the inverse problem solution. The variations in the stress-strain fields and spatial distribution of the stored potential energy density were found by the displacements of the daylight surface points in Tunkinsk geodetic proving ground in 1975 - 1986.     

电站锅炉制粉系统的爆炸原因与防范对策

火力发电厂制粉系统爆炸事故时有发生 ,重大设备损坏 ,造成了严重的经济损失。本文通过分析研究 ,找出制粉系统爆炸的原因 ,从措施上、煤的质量控制上及制粉系统结构改造上提出了防范的对策。     

控制图在土坝粘土填筑干密度控制中的应用

应用统计控制图法，选用平均值——标准差、平均值——极差控制图法，控制24^#坝粘土填筑干密度值及施工偶然异常波动，早期提出警报，以保证土坝的施工质量。     

空分设备系统操作中的物料平衡

本文以济南鲍德气体有限公司 2 0 0 0 0m3 /h空分设备为例 ,从物料平衡的观点出发 ,阐述了操作中一些应注意的问题及解决的措施。     

Preparation and properties of novel polyurethane insulating coatings based on glycerin‐terminated urethane prepolymers and blocked isocyanate

Novel polyurethane insulating coatings were prepared from the reaction of glycerin‐terminated polyurethane prepolymers (GPUPs) and a blocked isocyanate curing agent (BIC). The GPUPs were prepared from the reaction of one equivalent of polycaprolactone polyol (CAPA 210) with an excess amount of 4,4′‐methylene bis(phenyl isocyanate) (MDI) and subsequent reaction of the NCO‐terminated polyurethane with glycerin. The BIC was prepared from the reaction of trimethylol propane (TMP), toluene diisocyanate (TDI) and N‐methylaniline (NMA). The polyols and curing agent were characterized by conventional methods while the curing condition was optimized via gel content measurements. The curing kinetics of the polyurethane coating were investigated and the kinetic parameters derived. The crosslink densities of the samples were determined via the equilibrium swelling method, using the Flory–Rehner equation. The relationships between the crosslink density and the electrical, physical, mechanical and dynamic mechanical properties of the coatings were also studied. Copyright © 2005 Society of Chemical Industry     

Low density polyethylene and grafted lignin polyblends using epoxy‐functionalized compatibilizer: mechanical and thermal properties

Lignin was graft copolymerized with methyl methacrylate using manganic pyrophosphate as initiator. This modified lignin was then blended (up to 50 wt%) with low density polyethylene (LDPE) using a small quantity of poly[ethylene‐co‐(glycidyl methacrylate)] (PEGMA) compatibilizer. The mechanical properties of the blend were substantially improved by using modified lignin in contrast to untreated lignin. Differential scanning calorimetry studies showed loss of crystallinity of the LDPE phase owing to the interaction between the blend components. Thermogravimetric analysis showed higher thermal stability of modified lignin in the domain of blend processing. This suggested that there is scope for useful utilization of lignin, which could also lead to the development of eco‐friendly products. Copyright © 2005 Society of Chemical Industry     

Finite‐Element Implementation of a Self‐consistent Texture Model with a Hardening Law Based on Dislocation Densities

A self‐consistent texture model is implemented in the finite‐element code ABAQUS/Explicit®. Hardening of the slip systems is described by evolution laws for dislocation densities, and the Bauschinger effect is included. With these ingredients the cold rolling of an IF‐steel is simulated and the evolution of texture and anisotropy is examined. The use of the dislocation based hardening law is found to have a significant effect on the evolution of the anisotropic yield surface, but only very little influence on the texture. Furthermore, the hardening model is used to investigate the evolution of dislocation densities in differently oriented grains during plane strain compression. It is found that the dislocation density varies greatly depending on orientation, an observation which can help to explain the orientation dependence of recrystallization.     

公路边坡培植柠条的探讨

介绍了河曲公路所处的自然环境 ,阐述了人工铲草的利与弊 ,进而提出了边坡培植柠条的效益分析 ,并对培植柠条的苗期管理及与养护生产的关系进行了介绍