光催化降解废气过程中紫外辐射照度模拟和优化

为在光催化设计中合理布置紫外灯,减少光在传输过程中的损失,概括总结径向辐射模型、多点源叠加近似辐射模型和离散坐标辐射模型等3种经典的紫外辐射物理模型;基于离散坐标辐射模型模拟某公司生产的光催化氧化废气处理装置的紫外辐射照度;通过调整灯管布置距离改变光强分布,并拟合光催化单元和光催化网表面的平均紫外辐射照度随灯管布置距离变化曲线.结果表明,距离参数在55～65 mm时,该光催化反应装置的光能利用率较好;紫外灯的合理布置可有效提高光能利用率.     

Effects of the International Temperature Scale of 1990 (ITS-90) on CIE Documentary Standards for Radiometry,Photometry, and Colorimetry

The differences between ITS-90 and IPTS-68 above 1235 K are described. It is shown that none of the following CIE definitions or recommendations require revision because of the introduction of the ITS-90: International Lighting Vocabulary definitions; CIE Standard Illuminants A, D₆₅, other illuminants; and sources for realizing CIE Illuminants. The effect of the ITS-90 on previously calibrated sources for realizing CIE illuminants is negligibly small.²     

Bayesian network based general correspondence retrieval method for depth sensing with single-shot structured light

This study reinvestigated one of the most fundamental problems in structure light depth sensing field: correspondence retrieval of features between patterns and images. We formulate the global optimum correspondence retrieval by maximizing a conditional probability of correspondence given observed features, which is depicted by a Bayesian network. Different from traditional “code-only” based correspondence retrieval methods, the proposed Bayesian network based method exploits the positional correlations of correspondences of neighboring features, namely, the correspondences of poorly detected features are estimated with the aid of the correspondences of well detected features. The method performs especially well on challenging scenes with rich depth variations, abrupt depth changes, edges, etc. Experiments show that the proposed method increase the correspondence accuracy by about 40% on challenging scenes, compared with traditional “code-only” based correspondence retrieval methods.     

基于FPGA的开关量输入模块设计

在测控系统中,经常需要对各种现场信号进行采集;该模块主要实现对开关量状态信号进行实时监控,记录状态信息,为故障诊断提供依据;在设计中,采用了光耦隔离器件对输入信号进行了隔离和抗干扰处理,使用了FPGA实现了数据实时采集和中断处理,最后经PCI总线与主机进行数据交互;在故障诊断系统中,该信号采集板工作稳定、可靠,能够满足系统的实时性要求。     

Roll‐to‐roll UV embossing process applied for light bar‐based sub‐wavelength gratings for backlight

This study proposes a roll‐to‐roll process‐based sub‐wavelength grating, which is attached on a light bar to turn the side‐lit red/green/blue (620, 520, and 450 nm) incident rays into a uniformly and normally output white light with high illuminance from the light bar's surface. On the basis of the rigorous coupling wave analysis, the relationship between the first‐order transmission/reflection efficiency and the pitch of the gratings with different shapes was analyzed. The optimal design can effectively reduce the coupling length and enhance the white color balance for display applications.     

Thermal diffusivity of fluids in a broad region around the critical point

Dynamic light scattering is a suitable method for the investigation of transport properties such as the thermal diffusivity of optically transparent fluids. The main advantages of the method are its quickness, the fact of the thermodynamic state of equilibrium of the sample (gradients are not required), and the relatively simple evaluation of data without the necessity of calibration. However, an insufficient production of intensity of scattered light may be a limiting effect. For that reason the vicinity of the gas-liquid critical point represents the classical range of application. In this paper, it is shown that by means of an appropriate choice of experimental apparatus, measurements are also feasible in an extended range of states. Broad regions around critical points of three pure fluids (sulfur hexafluoride, SF₆; ethane, C₂H₆; nitrous oxide, N₂O) over temperature ranges ¦T-T _c¦ of 0.02 to 50 K and density ranges (/_c) of 0.2 to 2 were investigated. In this region the thermal diffusivity shows great variations with temperature and density and cannot be described by means of ideal-gas behavior or relations for liquids. The measurements were carried out along the coexistence curve for both phases, along the critical isochore and along some isotherms with TT _c. The measured or calculated density, pressure, and thermal diffusivity data as well as some correlations are presented.     

CHARAC TERIZATION OF TiAl POWDER PRODUCED BY MECHANICAL ALLOYING

The microstructure,alloying reaction and sintering behavior of the powder produced by Mechanical Al-loying(MA)for 8 h from 64 wt.-% Ti powder and 36 wt.-% Al powder were studied by scanning electronmicroscopy,optical microscopy,X-ray diffractometry,differential scanning calorimetry(DSC)and dilatometry.The mechanically alloyed powder partictes are Ti-Al composite particles.Thus,titanium aluminides can formeasily in the powder through diffusion during heat treatment.It is shown that the sintering behavior of this pow-der,different from the behaviors of TiAl alloy powder and mixed powder of 64 wt.-% Ti powder and 36 wt.-%Al powder,changes from expansion at temperatures below 1000℃ to shrinkage at temperatures above 1000℃.Homogeneously alloyed TiAl material with a density over 96% of the theoretical density can be produced fromthe mechanically alloyed powder by compaction-sintering.     

Fluorescent lamp promoted formaldehyde removal over CeO2 catalysts at ambient temperature

Exploring an alternative strategy with high efficiency and low cost to abate formaldehyde (HCHO) in indoor environment, is of increasing significance for people's health. CeO₂ catalysts prepared by hydrothermal, precipitation and calcination methods were investigated for HCHO removal at ambient temperature. It is found that indoor fluorescent light visibly boosts the catalytic performance of CeO₂ catalysts for HCHO decomposition at ambient temperature. Among the CeO₂ catalysts, CeO₂ prepared from hydrothermal method (CeO₂–H) exhibits a superior catalytic performance and an excellent durability by eight recycle times. Based on the characterization and analysis, the excellent catalytic performance of CeO₂–H is mainly contributed by its abundance of surface oxygen vacancies, and photogenerated electrons and hole activated by fluorescent light. This work shows a potential practicability in HCHO pollution elimination by taking full advantage of the existing lighting in indoor environments.     

Use of electron microscopy on microstructure characterization of high chromium cast irons

The physical metallurgy underlying the development of cast microstructures in abrasion resistant high chromium cast irons, and their structural modification by thermal treatments is relatively complex. Structural characterisation via electron microscopy therefore has a key role to play in furthering our understanding of the phase transformations that control the microstructures and hence the service performances of these irons as wear parts. This paper shows how both scanning and especially transmission electron microscopy can provide valuable information on the nature of eutectic and secondary carbides and on the matrix structures in these irons. Particular attention is given to current characterisation research on conventionally cast 30%Cr irons that are used for applications involving corrosive wear e.g. slurry pumps and on a semi-solid cast 27%Cr iron that has a potential for applications in industry.