Characteristics and formation mechanism of porosities in CFRP during laser joining of CFRP and steel

An experimental investigation on the mechanism of porosity formation during the laser joining of carbon fiber reinforced polymer (CFRP) and steel is presented. The porosity morphology and distribution were characterized by optical and scanning electron microscopy, and the thermal pyrolysis behaviors were investigated by thermal analysis and designed back-side cooling experiments. The results show that there are two types of porosities in CFRP. Porosity I only appears when the heat input is more than 77.8 J/mm. It has a smooth inner wall and distributes near the bonding interface between CFRP and steel at the central area of melted zone, which is caused by gaseous products such as CO₂, NH₃, H₂O, and hydrocarbons produced by the pyrolysis of CFRP. Porosity II can be seen under all joining conditions. It has a rough inner wall and distributes far away from the bonding interface, concentrating at the final solidification locations. Porosity II is caused by the shrinkage of melted CFRP during solidification stage.     

Effects of SO2 on selective catalytic reduction of NO with NH3 over a TiO2 photocatalyst

The effect of SO₂ gas was investigated on the activity of the photo-assisted selective catalytic reduction of nitrogen monoxide (NO) with ammonia (NH₃) over a TiO₂ photocatalyst in the presence of excess oxygen (photo-SCR). The introduction of SO₂ (300 ppm) greatly decreased the activity of the photo-SCR at 373 K. The increment of the reaction temperature enhanced the resistance to SO₂ gas, and at 553 K the conversion of NO was stable for at least 300 min of the reaction. X-ray diffraction, FTIR spectroscopy, thermogravimetry and differential thermal analysis, x-ray photoelectron spectroscopy (XPS), elemental analysis and N₂ adsorption measurement revealed that the ammonium sulfate species were generated after the reaction. There was a strong negative correlation between the deposition amount of the ammonium sulfate species and the specific surface area. Based on the above relationship, we concluded that the deposition of the ammonium sulfate species decreased the specific surface area by plugging the pore structure of the catalyst, and the decrease of the specific surface area resulted in the deactivation of the catalyst.     

Rapid detection of viable Bacillus cereus emetic and enterotoxic strains in food by coupling propidium monoazide and multiplex PCR (PMA-mPCR)

Bacillus cereus can cause emetic and diarrheal food poisoning. It is widespread in nature and therefore, considered a major foodborne pathogen. To develop a sensitive and reliable assay for detecting enterotoxin genes (nheA, entFM, hblD, cytK) and emetic toxin (ces), specific primers each targeting one individual gene were designed. Propidium monoazide (PMA) was coupled with the developed multiplex PCR (mPCR) for the detection of viable B. cereus. The inclusivity and exclusivity of the PMA-mPCR was confirmed using a panel of 44 strains including 17 emetic and 9 enterotoxic B. cereus reference strains and 18 non-target strains. The limit of detection (LOD) without PMA treatment in pure DNA was 2 pg/reaction tube. The LOD of mPCR assay in pure heat-killed dead bacteria was 4.0 × 10² CFU/mL. Also, the LOD on the viable bacteria with or without PMA treatment was similar (3.8 × 10² CFU/mL) showing that the PMA treatment did not significantly decrease sensitivity. Finally, the newly developed PMA-mPCR successfully detected 4.8 × 10³ and 3.6 × 10³ CFU/g of viable B. cereus F4810/72 (emetic) and B. cereus ATCC 12480 (enterotoxic) reference strains, respectively, in food samples. Hence, this study combines PMA and mPCR to detect viable B. cereus with a wide range of toxin detection (5 toxins). Thus, the novel PMA-mPCR assay developed in this study is a rapid and efficient diagnostic tool for the monitoring of viable B. cereus in food samples and potentially other samples via appropriate DNA extraction.     

不同晶相结构ZrO2负载铜基催化剂用于二乙醇胺脱氢反应

通过制备不同晶相结构〔单斜相(m-ZrO_2)、四方相(t-ZrO_2)和无定型(a-ZrO_2)〕ZrO_2载体,再通过沉积沉淀法制得Cu/m-ZrO_2、Cu/t-ZrO_2和Cu/a-ZrO_2催化剂,分别用于催化二乙醇胺脱氢合成亚氨基二乙酸反应。采用XRD、氮气物理吸附脱附、XPS、H_2-TPR、CO_2-TPD对催化剂的结构进行了表征。结果表明,Cu/m-ZrO_2催化剂界面更加有利于Cu~+/Cu~0稳定存在,具有更多的碱性位点,且抗氧化性较好。在二乙醇胺脱氢反应中,Cu/m-ZrO_2催化剂性能最好,反应时间为2.5 h,亚氨基二乙酸收率为97.64%。     

Hydrocarbon-based electrode ionomer for proton exchange membrane fuel cells

The electrode ionomer is a key factor that significantly affects the catalyst layer morphology and fuel cell performance. Herein, sulfonated poly(arylene ether sulfone)-based electrode ionomers with polymers of various molecular weights and alcohol/water mixtures were prepared, and those comprising the alcohol/water mixture showed a higher performance than the ones prepared using higher boiling solvents, such as dimethylacetamide; this is owing to the formation of the uniformly dispersed ionomer catalyst layer. The relation between ionomer molecular weight for the same polymer structure and the sulfonation degree was investigated. Because the chain length of polymer varies with molecular weight and chain entanglement degree, its molecular weight affects the electrode morphology. As the ionomer covered the catalyst, the agglomerates formed were of different morphologies according to their molecular weight, which could be deduced indirectly through dynamic light scattering and scanning electron microscopy. Additionally, the fuel cell performance was confirmed in the current-voltage curve.     

Formulation of sage essential oil (Salvia officinalis,L.) monoterpenes into chitosan hydrogels and permeation study with GC-MS analysis

This study deals with the formulation of natural drugs into hydrogels. For the first time, compounds from the sage essential oil were formulated into chitosan hydrogels. A sample preparation procedure for hydrophobic volatile analytes present in a hydrophilic water matrix along with an analytical method based on the gas chromatography coupled with the mass spectrometry (GC-MS) was developed and applied for the evaluation of the identity and quantity of essential oil components in the hydrogels and saline samples. The experimental results revealed that the chitosan hydrogels are suitable for the formulation of sage essential oil. The monoterpene release can be effectively controlled by both chitosan and caffeine concentration in the hydrogels. Permeation experiment, based on a hydrogel with the optimized composition [3.5% (w/w) sage essential oil, 2.0% (w/w) caffeine, 2.5% (w/w) chitosan and 0.1% (w/w) Tween-80] in donor compartment, saline solution in acceptor compartment, and semi-permeable cellophane membrane, demonstrated the useful permeation selectivity. Here, (according to lipophilicity) an enhanced permeation of the bicyclic monoterpenes with antiflogistic and antiseptic properties (eucalyptol, camphor and borneol) and, at the same time, suppressed permeation of toxic thujone (not exceeding its permitted applicable concentration) was observed. These properties highlight the pharmaceutical importance of the developed chitosan hydrogel formulating sage essential oil in the dermal applications.     

Parallel chaos optimization algorithm with migration and merging operation

Chaos optimization algorithm (COA) utilizes the chaotic maps to generate the pseudo-random sequences mapped as the decision variables for global optimization applications. A kind of parallel chaos optimization algorithm (PCOA) has been proposed in our former studies to improve COA. The salient feature of PCOA lies in its pseudo-parallel mechanism. However, all individuals in the PCOA search independently without utilizing the fitness and diversity information of the population. In view of the limitation of PCOA, a novel PCOA with migration and merging operation (denoted as MMO-PCOA) is proposed in this paper. Specifically, parallel individuals are randomly selected to be conducted migration and merging operation with the so far parallel solutions. Both migration and merging operation exchange information within population and produce new candidate individuals, which are different from those generated by stochastic chaotic sequences. Consequently, a good balance between exploration and exploitation can be achieved in the MMO-PCOA. The impacts of different one-dimensional maps and parallel numbers on the MMO-PCOA are also discussed. Benchmark functions and parameter identification problems are used to test the performance of the MMO-PCOA. Simulation results, compared with other optimization algorithms, show the superiority of the proposed MMO-PCOA algorithm.     

Mechanical damage characterization of glass fiber-reinforced polymer laminates by ultrasonic maps

A method for simultaneous measurement of the thickness and density for Glass Fiber-Reinforced Polymer (GFRP) laminate plates with ultrasonic waves in C-Scan mode is presented in the form of maps. The method uses three different signals in immersion pulse-echo C-Scan mode. The maps obtained based on the density show the heterogeneity of the material at high resolution at the pixel level (1 × 1 mm²) and therefore they represent an efficient tool to assess and evaluate the damage of the composite structures after manufacturing and after an applied mechanical loading.     

Behavior of 316L stainless steel containing corrosion pits under cyclic loading

The environmental performance of 316L grade stainless steel, in the form of tensile specimens containing a single corrosion pit with various aspect ratios, under cyclic loading in aerated chloride solutions is investigated in this study. Results from environmental tests were compared and contrasted with those obtained using finite element analysis (FEA). Fractography of the failed specimens obtained from experiments revealed that fatigue crack initiation took place at the base of the shallow pit. The crack initiation shifted towards the shoulder and the mouth of the pit for pits of increasing depth. This process is well predicted by FEA, as the strain contour maps show that strain is the highest around the centric strip of the pit. However, for shallow pits, local strain is uniformly distributed around that strip but begins to concentrate more towards the shoulder and the mouth region for increasingly deep pits.     

共享交通的时空轨迹检索与群体发现

为解决共享交通下的共乘用户群体发现效率低、准确率不高问题，依据R-树原理建立GeoOD-Tree索引，并在此基础上提出以最大化共乘率为目标的群体发现策略。首先，对原始时空轨迹数据进行特征提取与标定处理，挖掘有效出行起讫点（OD）轨迹；其次，针对用户起讫点轨迹的特征，建立GeoOD-Tree索引进行有效的存储管理；最后，给出以最大化共乘行程为目标的群体发现模型，并运用K最近邻（KNN）查询对搜索空间剪枝压缩，提高群体发现效率。采用西安市近12000辆出租车营运轨迹数据，选取动态时间规整（DTW）等典型算法与所提算法在查询效率与准确率上进行性能对比分析。与DTW算法相比，所提算法的准确率提高了10.12%，查询效率提高了约15倍。实验结果表明提出的群体发现策略能有效提高共乘用户群体发现的准确率和效率，可有效提升共乘出行方式的出行率。