Synthesis,characterization and ion exchange properties of zirconium(IV) tungstoiodophosphate,a new cation exchanger

Zirconium(IV) tungstoiodophosphate has been synthesized under a variety of conditions. The most chemically and thermally stable sample is prepared by adding a mixture of aqueous solutions of 0·5 mol L⁻¹ sodium tungstate, potassium iodate and 1 mol L⁻¹ orthophosphoric acid to aqueous solution of 0·1 mol L⁻¹ zirconium(IV) oxychloride. Its ion exchange capacity for Na⁺ and K⁺ was found to be 2·20 and 2·35 meq g⁻¹ dry exchanger, respectively. The material has been characterized on the basis of chemical composition, pH titration, Fourier transform infrared spectroscopy (FTIR) and thermogravimetric analysis. The effect on the exchange capacity of drying the exchanger at different temperatures has been studied. The analytical importance of the material has been established by quantitative separation of Pb²⁺ from other metal ions.     

Synthesis of LiFePO4 with fine particle by co-precipitation method

LiFePO₄ is a potential candidate for the cathode material of the lithium secondary batteries. A co-precipitation method was adopted to prepare LiFePO₄ because it is simple and cheap. Nitrogen gas was needed to prevent oxidation of Fe²⁺ in the aqueous solution. The co-precipitated precursor shows the high reactivity with the reductive gas, and the single phase of LiFePO₄ is successfully synthesized with the aid of carbon under less reductive conditions. LiFePO₄ fine powder prepared by co-precipitation method shows high rate capability, impressive specific capacity and cycle property.     

A new iterative order reduction (IOR) method for eigensolutions of large structures

Order reduction is a computationally efficient method to estimate some lowest eigenvalues and the corresponding eigenvectors of large structural systems by reducing the order of the original model to a smaller one. But its accuracy is limited to a small range of frequencies that depends on the selection of the retained degrees of freedom. This paper proposes a new iterative order reduction (IOR) technique to obtain accurately the eigensolutions of large structural systems. The technique retains all the inertia terms associated with the removed degrees of freedom. This hence leads to the reduced mass matrix being in an iterated form and the reduced stiffness matrix constant. From these mass and stiffness matrices, the eigensolutions of the reduced system can be obtained iteratively. On convergence the reduced system reproduces the eigensolutions of the original structure. A proof of the convergence property is also presented. Applications of the method to a practical GARTEUR structure as well as a plate have demonstrated that the proposed method is comparable to the commonly used Subspace Iteration method in terms of numerical accuracy. Moreover, it has been found that the proposed method is computationally more efficient than the Subspace Iteration method. Copyright © 2003 John Wiley & Sons, Ltd.     

Visual evaluation at scale of threshold to suprathreshold color difference

Visual evaluation experiments of color discrimination threshold and suprathreshold color‐difference comparison were carried out using CRT colors based on the psychophysical methods of interleaved staircase and constant stimuli, respectively. A large set of experimental data was generated ranged from threshold to large suprathreshold color difference at the five CIE color centers. The visual data were analyzed in detail for every observer at each visual scale to show the effect of color‐difference magnitude on the observer precision. The chromaticity ellipses from this study were compared with four previous published data, of CRT colors by Cui and Luo, and of surface colors by RIT‐DuPont, Cheung and Rigg, and Guan and Luo, to report the reproducibility of this kind of experiment using CRT colors and the variations between CRT and surface data, respectively. The present threshold data were also compared against the different suprathreshold data to show the effect of color‐difference scales. The visual results were further used to test the three advance color‐difference formulae, CMC, CIE94, and CIEDE2000, together with the basic CIELAB equation. In their original forms or with optimized K_L values, the CIEDE2000 outperformed others, followed by CMC, and with the CIELAB and CIE94 the poorest for predicting the combined dataset of all color centers in the present study. © 2005 Wiley Periodicals, Inc. Col Res Appl, 30, 198–208, 2005; Published online in Wiley InterScience (www.interscience.wiley.com). DOI 10.1002/col.20106     

MIMO系统中简单的扩展空时块编码分集技术研究

本文提出一种多输入多输出（MIMO）天线系统中简单的扩展空时块编码（SSTBC）分集技术，采用沃尔什码来区分各天线发送数据子流。采用这种方法，在系统带宽一定时，不降低发送信息速率，同时接收机简单。不同天线的发送信息经过了所有收一发天线对之间的空间子信道，获得了所有路径的部分空间分集增益，仿真结果表明，这种增益的获得不受限于接收分集阶数，并且随发射天线的增加以一定的线性关系增加。     

一种基于判决反馈的OFDM系统载波频率跟踪算法

研究了多径信道下OFDM系统的一种新的载波频率跟踪算法，这种算法以判决反馈和接收端的时域信号重构为基础。推导了估计结果的精确解，比较了使用原估计结果和新的估计结果进行频偏补偿时系统跟踪性能的不同。通过对算法的仔细分析，发现除了通常的加性噪声外，信道估计误差、子载波数目和子载波的调制方式也影响频偏的估计结果和跟踪范围，而且子载波的数目和调制方式是决定性的因素。这种频率跟踪方法的优点是即使在很低的信噪比下仍然能获得高的跟踪精度，且实现相对简单。     

Assessing organo-clay dispersion in polymer layered silicate nanocomposites: A SAXS approach

A SAXS method for the quantitative assessment of the morphology of polymer layered silicate nanocomposites is proposed. Fitting the SAXS patterns, the number of clay layers, the periodicity of the layers in the tactoids, the thickness of the regions interposed between the clay platelets and their distributions can be measured. A good agreement with TEM data was obtained, avoiding the inconsistencies with microscopical observations often reported in the literature.     

Synthesis and characterization of a series of star-branched poly(ε-caprolactone)s with the variation in arm numbers and lengths

A series of star-branched poly(ε-caprolactone)s (SPCLs) was synthesized with structural variation of the arm numbers and lengths through ring-opening polymerization under bulk condition. Arm numbers were varied to be 3, 4, and 6 by using multifunctional initiating cores such as trimethylol propane, pentaerythritol, and dipentaerythritol, respectively. The lengths of the poly(ε-caprolactone) arms were varied by controlling the molar ratio of monomer-to-initiating hydroxyl group molar ratio ([CL]₀/[-OH]₀=5, 10, 15). Molecular weights were determined by both ¹H NMR end-group analysis and MALDI-TOF mass spectrometry, which gave reasonably consistent values. On the contrary, the GPC method failed to give accurate values of molecular weight of SPCLs due to the discrepancy with the linear standard. The branching architecture of SPCLs was evaluated by the branching ratio, g, which is the ratio of the mean-square radius of SPCL to that of liner counterpart, linear poly(ε-caprolactone) (LPCL), which is of the same chemistry and having the same molecular weight. The radii of gyration of SPCLs and LPCLs were determined using small-angle X-ray scattering (SAXS) from the initial slopes of Zimm plots, represented as 1/I(q) vs q² with I(q) and q being the scattered intensity and scattering vector, respectively. The g values were observed to decrease with increasing arm numbers, indicating more compact molecular structure for SPCLs with higher arm numbers, while no such effect was observed for arm length variation. Thermal properties as well as the degree of crystallinity of SPCLs were found to be also dependent on structural variations. The melting points and the degradation temperatures were observed to increase with increasing arm lengths but with constant arm number. On the other hand, arm number variation with constant arm length gave no such changes to the thermal transitions of SPCLs. However, for the SPCLs with equivalent molecular weights, the degree of crystallinity was found to decrease with increasing arm numbers.     

Potential tissue implants from the networks based on 1,5-dioxepan-2-one and ε-caprolactone

The synthesis and characterization of degradable polymeric networks for biomedical applications was performed. Cross-linked films of poly(ε-caprolactone) (PCL) and poly(1,5-dioxepan-2-one) (PDXO) having various mole fractions of monomers and different cross-link densities were successfully prepared using 2,2′-bis-(ε-caprolactone-4-yl) propane (BCP) as cross-linking agent. Reaction parameters were carefully examined to optimise the film-forming conditions. Networks obtained were elastomeric materials, easy to cast and remove from the mould. Effect of CL content and cross-link density on the final properties of the polymer network was evaluated. High CL content or degree of cross-linking led to increase in Young's modulus and decrease in elongation at break. An increase in crystalline domains in films having a higher CL content was observed by optical microscopy. A greater thermal stability was observed in films having a high CL content. The hydrophilicity of the materials could be tailored by changing the CL content. The surface of the films became rougher with higher CL content.     

A simple mathematical analysis on the effect of sand in Cr(VI) reduction using zero valent iron

A simple mathematical model was proposed to analyze the enhancement of Cr(VI) reduction when sand materials are added to the zero valent iron (ZVI). Natural decay of Cr(VI) in a control experiment was analyzed by using a zero-order decay reaction. Adsorption kinetics of Cr(VI) to sand was modeled as a first-order reversible process, and the reduction rate by ZVI was treated as a first-order reaction. Natural decay of Cr(VI) was also included in other experiments, i.e., the adsorption to sand, the reduction by ZVI, and both adsorption and reduction when sand and ZVI are present together. The model parameters were estimated by fitting the solution of each model to the corresponding experimental data. To observe the effect of sand addition to ZVI, both adsorption and reduction rate models were considered simultaneously including the natural decay. The solution of the combined model was fitted to the experimental data to determine the first-order adsorption and reduction rate constants when sand as well as ZVI is present. The first-order reduction rate constant in the presence of sand was about 35 times higher than that with ZVI only.