Toughening of AT-Resins with a Polyphenylquinoxaline

Acetylene terminated (AT) resins are addition-curable thermoset materials which do not generate volatiles during cure and therefore can be fabricated into void-free structures. They retain good thermal and mechanical properties even after exposure to high humidity environments. Their use as composite matrix resins and adhesives has shown promise. These resins, however, are brittle. Molecular structure modifications and blending with thermoplastic modifiers have been used to improve their toughness. In this work, improvement in toughness has been sought through the use of a polyphenylquinoxaline (PPQ) modifier. The blended systems showed improvements in toughness, thermooxidative stability, and lap shear strength over the original AT-resins.     

Mode of crosslinking of degradable poly(vinylpyridine N-oxide) gels

The degradation mechanism of gels from poly(vinylpyridine N-oxide) was investigated by differential scanning calorimetry, C, H, N analysis, infra-red spectroscopy and degradability tests. It was found that poly(2-vinyl pyridine N-oxide) gels, regardless of the persulphate initiator used, were weaker than poly(4-vinyl pyridine N-oxide) gels. C, H, N analysis and infra-red spectroscopy indicated that the initiator becomes an integral part of the gels. A mechanism for the formation of the gels is proposed.     

温度对非晶硅薄膜二次晶化的影响

为研究温度对固相晶化的影响,用玻璃作衬底,在不同温度下用PECVD法直接沉积非晶硅(a-Si:H)薄膜,把在室温、350℃和450℃下沉积的样品,在600℃和850℃下退火3h,把前后样品用拉曼光谱和扫描电镜分析,发现二次晶化后的晶化效果比直接沉积的薄膜好,850℃下退火的薄膜比600℃好。在450℃下沉积、850℃退火3h,SEM观察,表面最大晶粒尺寸为900nm左右。     

Room‐Temperature Tailoring of Vertical ZnO Nanoarchitecture Morphology for Efficient Hybrid Polymer Solar Cells

A ZnO nanoarchitecture, i.e., ZnO nanosheet (NS) framework, is demonstrated to be a promising electron acceptor and direct electron transport matrix for polymer‐inorganic hybrid solar cells. The ZnO NS framework is constructed on nanoneedles/indium tin oxide substrate via a room‐temperature chemical bath deposition (RT CBD). The framework morphology can be simply tailored by varying the concentration of precursor solution in the RT CBD. The ZnO nanoarchitecture with an appropriate free space between the NSs is consequently demonstrated to facilitate poly(3‐hexylthiophene) (P3HT) infiltration, resulting in superior interface properties, i.e., more efficient charge separation and less charge recombination, in the hybrid. Moreover, apart from the characteristics similar to the ZnO nanorod (NR) array, including vertical feature and single crystalline structure, the ZnO NS framework exhibits a slightly larger absorption edge and a faster electron transport rate. A notable efficiency of 0.88% is therefore attained in the ZnO NS‐P3HT hybrid solar cell, which is higher than that of the ZnO NR‐P3HT hybrid solar cell.     

Durable electrochromic coatings prepared from electronically conductive poly(3HT-co-3TPP)-silica hybrid materials

In this paper, a series of organic-inorganic hybrid materials, consisting of heterocyclic conjugated poly(3-hexylthiophene), P3HT, network, and silica particles, were successfully prepared for electrochromic studies. First, the heterocyclic co-polymer of poly[3-hexylthiophene-co-N-(3-trimethoxysilylpropyl) pyrrole], P(3HT-co-3TPP), containing trimethoxysilyl functional groups in the co-polymer backbone as the sol-gel precursor were prepared by conventional oxidative polymerization. Subsequently, P(3HT-co-3TPP)-silica hybrid sol-gel materials in the form of coatings were prepared by baking the microslides and ITO-coated electrodes that had been cast with homogeneous blending solutions containing co-polymer, acid-dopant, tetraethyl orthosilicate (TEOS), and a few drops of water. The microstructures of silica particles formed in the P(3HT-co-3TPP)-silica hybrid materials were investigated by transmission electron microscopy (TEM). The as-prepared hybrid coatings had improved adhesion capability on inorganic glass substrates relative to the pure P3HT on the basis of electrochemical cyclic voltammetric studies and Scotch tape test evaluations. During potential cycling, the film color of P(3HT-co-3TPP)-silica hybrid materials and P3HT coated on ITO electrode changed from orange yellow (i.e., reduced form) to dark blue (i.e., oxidized form) as the redox reactions proceeded. Effects of the material composition of P3HT along with hybrid materials on the electrochemistry, spectroelectrochemistry, thermal stability, and electrical conductivity were also studied.     

Nitrate Additives Coordinated with Crown Ether Stabilize Lithium Metal Anodes in Carbonate Electrolyte

Lithium metal anodes (LMAs) are promising for next-generation batteries but have poor compatibility with the widely used carbonate-based electrolytes, which is a major reason for their severe dendrite growth and low Coulombic efficiency (CE). A nitrate additive to the electrolyte is an effective solution, but its low solubility in carbonates is a problem that can be solved using a crown ether, as reported. A rubidium nitrate additive coordinated with 18-crown-6 crown ether stabilizes the LMA in a carbonate electrolyte. The coordination promotes the dissolution of NO₃⁻ ions and helps form a dense solid electrolyte interface that is Li₃N-rich which guides uniform Li deposition. In addition, the Rb (18-crown-6)⁺ complexes are adsorbed on the dendrite tips, shielding them from Li deposition on the dendrite tips. A high CE of 97.1% is achieved with a capacity of 1 mAh cm⁻² in a half cell, much higher than when using the additive-free electrolyte (92.2%). Such an additive is very compatible with a nickel-rich ternary cathode at a high voltage, and the assembled full battery with a cathode material loading up to 10 mg cm⁻² shows an average CE of 99.8% over 200 cycles, indicating a potential for practical use.     

Improved morphology and enhanced stability via solvent engineering for planar heterojunction perovskite solar cells

Solvent engineering technique for planar heterojunction perovskite solar cells is an efficient way to achieve uniformly controlled grain morphology for perovskite films. In this report, diethyl ether solvent engineering technique was used for Methyl ammonium lead triiodide (CH₃NH₃PbI₃) perovskite thin films for planar heterojunction solar cells which exhibited a PCE of 9.20%. Morphological improvements and enhanced grain sizes leads to enhanced absorption of CH₃NH₃PbI₃. Moreover solar cells have showed an excellent environmental stability of more than 100 days. This increase in efficiency is due to improved film morphology of perovskite layer after solvent treatment which has been revealed under UV–Vis spectroscopy, SEM images, X-ray diffraction and impedance spectroscopy.     

Temperature gradient controlled crystal growth from TIPS pentacene-poly(α-methyl styrene) blends for improving performance of organic thin film transistors

6,13-bis(triisopropylsilylethynyl) pentacene (TIPS pentacene) from simple drop casting typically forms crystals with random orientation and poor areal coverage, which leads to device-to-device performance variation of organic thin film transistors (OTFTs). Previously, a temperature gradient technique was developed to address these problems. However, this approach simultaneously introduced thermal cracks due to the thermally induced stress during crystallization. These thermal cracks accounted for a reduction of charge transport, thereby impacting the device performance of TIPS pentacene based OTFTs. In this work, an insulating polymer, poly(α-methyl styrene) (PαMS) was blended with TIPS pentacene to relieve the thermal stress and effectively prevent the generation of thermal cracks. The results demonstrate that the incorporation of PαMS polymer combined with the temperature gradient technique improves both the hole mobility and performance consistency of TIPS pentacene based OTFTs.     

一种新型高速宽带数字下变频器的FPGA实现

数字下变频器是软件无线电宽带数字接收机的核心组成部分,经典的数字下变频结构难以实现高速率的混频与滤波,因此针对软件无线电系统小型化和低功耗的要求,提出一种新型的宽带数字接收机中数字下变频器的设计与FPGA实现方法,该方法采用基于多相滤波正交化处理从而实现数字接收机。文中分析了其设计原理以及FPGA实现,测试结果表明,设计具有良好的可扩展性和灵活性。     

机顶盒的以太接口设计和实现

以LSI方案机顶盒的SC2000芯片为例,详细地阐述了基于此方案的机顶盒的以太接口的硬件设计和实现,同时介绍了在机顶盒中运用TCP/IP协议进行通信时所运用到的pSOSystem操作系统中的pNA 模块,最后给出了开发的两个应用实例.