佛尔哈德法测定氯化除汞上清液中的氯量

控制pH4-6，用锌粉还原氯化除汞上清液中的汞（Ⅱ）离子，取置换后液加入过量的硝酸银标准溶液，以硫酸铁铵溶液作指示剂，用硫氰酸钾标准滴定溶液滴定来测定氯量。该方法的检出限：0．25mg／100mL，回收率：98％-101％。     

从氯化铅渣中回收铅铋的研究

本文以柿竹园有色金属矿粗铋火法精炼、气化除铅产出的铅渣为原料，在常压下采用氯化钠水溶液进行浸出处理，有效地分离了铅和铋，并将铅制成了化工产品黄丹及硫酸铅     

在高速气流粉碎作用下PVC的力化学降解及形态变化的研究

通过ＧＰＴ、ＦＴ－ＩＲ、ＳＥＭ和力学性能测试，研究了在高速气流作用下聚氯乙烯（ＰＶＣ）的力化学降解反应、颗粒形态和微晶结构变化及其对ＰＶＣ物理、力学性能的影响。实验结果表明，经过高速气流处理ＰＶＣ，分子量将有所降低，晶体结构发生变化，颗粒尺寸和表观密度降低，比表面积增大，加工性能和力学性能得到明显改善。     

Factors Affecting 1-Octen-3-ol in Mushrooms at Harvest and During Postharvest Storage

Harvesting experiments revealed that immature whole mushrooms with closed veils had higher 1-octen-3-0l levels than more mature whole mushrooms with open veils. The l-octen-3-01 content of the gills was higher in immature mushrooms with closed veils, gradually decreased with maturity as the veil opened, and finally increased after the gills were well exposed. Postharvest experiments demonstrated that storage temperature influenced the activity of lipoxygenase-hydroperoxide lyase, but no differences in 1-octen-3-01 content were observed. Enzyme activity as well as 1-octen-3-01 content decreased during storage. Addition of calcium chloride to irrigation water, employed to improve quality and shelf life of fresh mushrooms, increased the amount of l-octen-3-01 immediately after harvest.     

Pitting corrosion of Cr–Mn–N steel in sulphuric acid media

The resistance to pitting corrosion of austenitic stainless steel Cr18Mn12N has been studied in model solutions of sulphuric acid (0.5 m) containing chloride ions (0.5 m). The cyclic potentiodynamic method has been employed to investigate the effects of chloride ions and agitation rate on the pitting and repassivation potentials. Electron and optical microscopy, electron diffraction spectroscopy and atomic absorption spectrometry have been used to detect the surface sites for pit formation and the growth of pit nuclei. The results obtained with chromium–manganese–nitrogen steel have been compared with those of austenitic Cr18Ni9 stainless steel. A similarity in pit initiation is established, while steel composition exhibits no significant effect. Cr18Mn12N steel is less prone to repassivation as compared with Cr18Ni9 steel.     

丙烯酰胺-二甲基二烯丙基氯化铵反相微乳液体系的制备及表征

采用石油醚为连续相、失水山梨糖醇酐单油酸酯(Span80)和聚氧乙烯失水山梨醇单硬脂酸酯(Tween80)为复合乳化剂、正己醇为助乳化剂,建立了丙烯酰胺(AM)和二甲基二烯丙基氯化铵(DMDAAC)反相微乳液体系。使用Zeta电位/粒度/相对分子质量分析仪对该体系的形成及聚合过程中乳胶粒子粒径及其分布进行了测试。实验结果表明,当体系达到微乳液状态时,体系主要由10~100nm的单体微珠及少量粒径小于10nm的胶束组成;随聚合过程的进行,胶束消失,乳胶粒子体积增大。乳胶粒子体积的增大主要是通过扩散和碰撞两种机理完成的。最佳的复合乳化剂亲水-亲油平衡值为8.045,复合乳化剂在油相中的质量分数为33%,助乳化剂在油相中的质量分数为1.6%。在此条件下达到微乳液状态时的水相增容体积最大。     

"牺牲"阳极法合成乙醇钽研究

研究了“牺牲“阳极法电化学合成乙醇钽过程中,添加剂种类与浓度、电解液温度、阴阳极极距和电流密度的影响.选取最佳合成条件为:四甲基氯化铵0.04 mol/L,温度为电解液的沸腾温度,极距约2 cm,电流密度220 A/m2.电合成的混合液经常压蒸馏和减压蒸馏,得到产品用红外光谱、拉曼光谱和元素分析进行表征,确定了产品为乙醇钽.电合成的电流效率大于95%,产品蒸馏时钽的直收率82.8%.     

Improving antibacterial,biocompatible, and reusable properties of polyvinyl chloride via the addition of aluminum alkoxides

Global bacterial infections associated with conventional polyvinyl chloride (PVC) medical devices place a heavy burden on healthcare systems and thus it will be desirable if medical devices are made from antimicrobial PVC. There are numerous studies focusing on polymer surface modifications to either leach antimicrobial agents or kill pathogenic microbes upon direct contact. In this work, mannitol fumarate ester-based aluminum metal alkoxide (MFE-Al) additive was developed to confer simultaneously improved antibacterial property and enhanced high temperature sterilization resistance of the resultant PVC. Data obtained confirm that the MFE-Al stabilized PVC sheets significantly inhibit 98% bacterial growth. They also show biocompatibility with cultured H9C2 cardiomyocytes and hemocompatibility in vitro. Dry heat sterilization is generally not suitable for PVC medical wares due to their poor thermal compatibility. Surprisingly, our antimicrobial-biocompatible PVC can maintain stability at 180°C for 90 min. Such a high thermal stability indicates the MFE-Al stabilized PVC can endure 90 cycles of dry-heat sterilization without significant damage. This study may provide a solution to reduce PVC medical waste for a maximum benefit without compromising human health or the environment.