Al(OH)3对硅橡胶性能的影响

综述了Al（OH)3粒径和用量对硅椽胶漏电电流、脉冲电流、耐漏电起痕、表面粗糙程度、电蚀损、介电性能、拉伸强度及漏电电流实验重复性的影响。     

新型难燃输送带胶粘剂的研制

以改性氯丁橡胶为主料、多异氰酸酯为固化剂制成的新型难燃输送带胶粘剂,具有粘接强度高、耐热性好、干燥时间短、难燃等特点,在常温常压下粘接输送带接头,固化30min即可负荷运行。     

Investigations of surface characterization of silicone rubber due to tracking phenomena under a.c. and d.c. voltages

In the present work, tracking phenomena has been studied with silicone rubber material under the a.c. and d.c. voltages following IEC-587 standards. The surface condition of the tracked zone was analysed using wide angle X-ray diffraction (WAXD) and thermogravimetric differential thermal analysis (TG-DTA) studies. The tracking time was different for a.c. and d.c. voltages.     

Dynamic-mechanical properties of polybutadiene rubbers

The dynamic properties of high-cis (98%) and cis-trans (42% cis) polybutadienes, crosslinked with 0.1 to 1.0% of crosslinking agent, have been studied using a torsion pendulum method over the temperature range ?170 to +20°C. For the high-cis rubber plots of damping factor (tan δ) against temperature showed the expected peak in the glass-transition region with an additional peak in the neighbourhood of 0°C attributable to crystallization. The cis-trans rubber showed two damping maxima in the transition region, separated by 30 to 40°C (depending on the degree of crosslinking), suggesting incipient phase separation of the component structures. The rebound resilience of the high-cis rubber at room temperature exceeded that of the cis-trans, reaching 92% at the highest crosslink density. Plots of resilience versus temperature for both rubbers showed a single minimum in the glass transition region.     

Linear viscoelastic properties of mixtures of 3- and 4-arm polybutadiene stars

The viscoelastic properties of a three-arm and a four-arm star polybutadiene with the same arm molecular weight (M_a) were studied. The zero-shear recoverable compliance (J⁰_e) and plateau modulus (G⁰_N) for these stars are the same. The zero-shear viscosity (η₀) of the three-arm star is 20% lower than that of the four-arm star. Mixtures of the stars had J⁰_e and G⁰_N unchanged. A $\text{50}\text{50}$ mixture of the three- and four-arm star was diluted with a low molecular weight linear polybutadiene. G⁰_N∝ø²; J⁰_e∝ø^?1 and M_e∝ø^?1, as expected for dilution with a θ-solvent.     

Thermoplastic elastomeric composition based on maleic anhydride–grafted ground rubber tire

Ground rubber tire (GRT) powder was maleated in an internal mixer using maleic anhydride and dicumyl peroxide at 160°C. Maleated GRT was characterized by using X‐ray photoelectron spectroscopy, Fourier transform infrared spectroscopy, wettability, and differential scanning calorimetry. The physical properties of the dynamically vulcanized 60 : 40, rubber : plastic composition based on acrylated high‐density polyethylene as the plastic phase and ethylene propylene diene rubber containing maleated GRT as the rubber phase were found to be greater than the corresponding composition containing nonmaleated GRT. The blend was found to be reprocessable, like themoplastic elastomers. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 370–378, 2002; DOI 10.1002/app.10348     

丁腈橡胶/导电粒子复合材料的正温度系数(PTC)特性

将导电粒子碳黑和铜粉分别与丁腈橡胶混合制备导电聚合物复合材料，其中碳黑（Ｎ５５０）／丁腈橡胶复合材料的电阻率随温度的变化呈现较强的正温度系数（ＰＴＣ）效应。讨论了掺入导电粒子浓度、结构和表面性质以及混炼硫化工艺等对该类材料的室温电阻率及ＰＴＣ效应的影响。     

Microstructure-related fracture toughness and fatigue crack growth behaviour in toughened, anhydride-cured epoxy resins

Fracture toughness and fatigue crack propagation (FCP) of plain and modified anhydride-cured epoxy resin (EP) were studied at ambient temperature. Liquid carboxyl-terminated acrylonitrile-butadiene (CTBN) and silicon (SI) rubber dispersions were used as tougheners for the EP. The morphology of the modified EP was characterized by dynamic mechanical analysis (DMA) and by scanning electron microscopy (SEM). The fracture toughness, K_c, of the compositions decreased with increasing deformation rate. K_c of the EP was slightly improved by CTBN addition and practically unaffected by incorporation of the SI dispersion when tests were performed at low cross-head speed, v. Both modifiers improved K_c at high v, and also the resistance to FCP, by shifting the curves to higher stress intensity factor ranges, ΔK, by comparison with the plain EP. It was established that both fracture and fatigue performance rely on the compliance, J_R, at the rubbery plateau, and thus on the apparent molecular mass between crosslinks, M_c. The failure mechanisms were less dependent upon the loading mode (fracture, fatigue), but differed basically for the various modifiers. Rubber-induced cavitation and shear yielding of the EP were dominant for CTBN, whereas crack bifurcation and branching controlled the cracking in SI-modified EP. The simultaneous use of both modifiers resulted in a synergistic effect for both the fracture toughness at high deformation rate and the FCP behavior.