Fabrication of High Performance PET/TLCP Fibers through the Synergistic Interfacial Enhancement and Compatibilization of Functional 1D and 2D Carbon Nanomaterials

The maleic anhydride functionalized graphene oxide (GO-MA) is fabricated by an efficient and solvent-free Diels–Alder reaction. Polyethylene terephthalate (PET)/thermotropic liquid crystal polyester (TLCP), PET/TLCP/GO-MA, PET/TLCP/aminated multi-walled carbon nanotubes (MWCNTs-NH₂), and PET/TLCP/GO-MA/MWCNTs-NH₂ composite fibers are systematically melt-spun. The structure and compatibilizing effects of GO-MA and MWCNTs-NH₂ on the mechanical, thermal, and crystallization properties of the composite fibers are indicated. The non-isothermal crystallization kinetics and X-ray diffraction (XRD) data show that TLCP and nanofillers can change the crystalline morphology of PET. The mechanical properties of the fibers rise with increasing TLCP content. The tensile strength 929 MPa and modulus 17.5 GPa of the fibers with 7 wt% TLCP and 0.25 wt% nanofillers (0.1 wt% GO-MA and 0.15 wt% MWCNTs-NH₂) are significantly higher than those with 7 wt% TLCP (tensile strength 622 MPa and modulus 16.1 GPa) and even higher than those with 15% TLCP (tensile strength 836 MPa, and modulus 18.0 GPa). When the GO-MA and MWCNTs-NH₂ co-exist, the anti-dripping phenomenon is improved. Therefore, the TLCP, GO, and MWCNTs synergistically strengthens the mechanical properties. This is promising for the industrial fabrication of high-strength fibers.     

低翘曲玻纤增强PET复合材料的制备和性能研究

依据降低翘曲的机理，选用不同降低翘曲的方法，制备了系列翘曲玻纤增强PET复合材料，结果表明，具有较高形状对称性的填料，如滑石粉，云母粉和玻璃微珠都能不同程度地降低玻纤增强PET体系的翘曲，非晶聚合物也能有效改进该体系的翘曲性能。     

塑料包装应用及技术进展

塑料在包装领域有着广泛的应用，其中聚酯（PET）性能优良，应用领域不断扩大。介绍了塑料包装不断通现的新技术，以及塑料包装环保问题的几点思路。     

PET/MFMB复合材料的力学性能、热性能的研究

用力学性能测定、DSC和熔体流动速率（MFR）测定法研究聚对苯二甲酸乙二酯／多功能母料（PET／MFMB）复合材料的力学性能和热性能。结果表明，当MFMB的含量为22％时，PET／MFMB复合材料的冲击强度、断裂伸长率分别出现极大值；复合材料中PET、PP的熔点比纯PET、纯PP的稍有降低，当PET／MFMB＝78／22时降低的幅度稍大；复合材料的MFR在PET／MFMB＝78／22时出现转变点。     

Surface hydrolysis of filaments based on poly(trimethylene terephthalate) spun at high spinning speeds

The surface alkaline hydrolysis of fibers made from poly(trimethylene terephthalate) (PTT) was studied after extruding the polymer at high spinning speeds from 2000 to 6000 m/min and heat setting in the range of temperatures from 100 to 180°C. Fiber weight loss increased with an increasing heat‐setting temperature but it was also dependent on the spinning speed. Some of the partially hydrolyzed fibers had a well‐developed, hydrophilic surface, and pore size in the range of 0.69 to 1.20 μm. The optimum reaction and morphological conditions for increasing porosity in PTT fibers depends on spinning speed and heat‐setting temperature. A temperature of 180°C is the upper limit for heat‐setting PTT filaments but seems to be the most effective for making porous fibers. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 1724–1730, 2004     

Stiffer and super-tough poly(butylene terephthalate) based blends by modification with phenoxy and maleated poly(ethylene-octene) copolymers

New super-tough poly(butylene terephthalate) (PBT) materials were obtained by melt blending PBT with both 20 wt% phenoxy (Ph) and 0-30 wt% maleic anhydride grafted poly(ethylene-octene) (mPEO) copolymers with different grafting levels. Ph was completely miscible in the PBT matrix. The presence of mPEO did not influence either the nature of the PBT-Ph matrix or the crystallization of PBT. The overall decrease in particle size and in interfacial tension upon grafting indicated that compatibilization had taken place. Super-tough (impact strength 23-fold that of the PBT) and stiffer PBT based blends were obtained at mPEO contents equal to or higher than 15%. The dependence of the critical inter-particle distance (τ_c), on both adhesion measured by means of the interfacial tension, and on the relation between the modulus of the matrix and that of the rubbery dispersed phase (E_m/E_d), is proposed.     

回收PET共混物的非等温结晶和熔融行为

采用双螺杆挤出机制备了聚丙烯(PP)/回收聚对苯二甲酸乙二酯(r-PET)、r-PET/马来酸酐接枝PP(PP-g-MAH)和r-PET/甲基丙烯酸缩水甘油酯接枝PP(PP-g-GMA)共混物,并研究了共混物组成、熔融温度与时间以及降温速率对共混物非等温结晶与熔融行为的影响.结果表明,r-PET与PP共混,结晶温度均提高,这与组分间起到异相成核诱导结晶作用有关.r-PET结晶温度随PP-g-MAH用量增加而降低,但受PP-g-GMA用量影响较小;r-PET可提高PP-g-MAH结晶温度,但降低PP-g-GMA结晶温度.熔融温度提高,共混物中PP结晶温度和熔点均降低,r-PET熔融峰形和熔点取决于共混物的熔融温度及界面相互作用.     

相容剂对PE-HD／PET共混合金性能的影响

以乙烯-丙烯酸丁酯-甲基丙烯酸缩水甘油酯三元共聚物（PTW）作为高密度聚乙烯（PE-HD）／聚对苯二甲酸乙二醇酯（PET）共混合金的反应性相容剂，采用熔融挤出法制备了以PE-HD为基体的PE～Hi）／PET、共混合金。通过力学性能和流变性能测试，扫描电镜（SEM）和动态力学分析（DMA）等手段，研究丁PTW对共混合金性能的影响。结果表明：PTW提高了体系的综合性能，当PE-HD／PET配比为90／10，PTW含量在5份时，其缺口冲击强度提高了近400％，拉伸强度和断裂伸长率分别提高了25％和50％，同时改善了共混合金的加工性能。SEM分析表明PTW的加入增大了共混合金的界面相互作用，促进了分散相粒子的细化，从而提高丁体系相容性，DMA测试表明，PTW的加入使PET的玻璃化转变温度向PE—HD的玻璃化转变温度靠近：     

An infra-red study of model compounds of poly(tetramethylene terephthalate)

An infra-red spectroscopic investigation of the poly(tetramethylene terephthalate) model compounds butyl-dibenzoate: C₆H₅COO(CH₂)₄OCOC₆H₅ (i), 1,4-bis-butyl terephthalate: HO(CH₂)₄-OCO₆H₄COO(CH₂)₄-OH (ii), α-butyl-ω-butoxyterephthalaoyl-di-(tetramethylene terephthalate): H(CH₂)₄(OCOC₆H₄COO-(CH₂)₄-)₃-OH (iii), and α-butyl-ω-butoxyterephthalaoyl-tetra-(tetra-methylene terephthalate): HO(CH₂)₄-(OCOC₆H₄COO(CH₂)₄-)₅-OH (iv) is presented. The synthesis of (i) is also described. Spectroscopic evidence indicates that the crystal conformations of the aliphatic segments in (i) and (ii) closely resemble the extended all trans beta form of PTMT. Oligomers (iii) and (iv), however, are found to be more similar to the crumpled alpha crystal phase of PTMT.     

Optimal reaction conditions for the minimization of energy consumption and by‐product formation in a poly(ethylene terephthalate) process

We determined the optimal reaction conditions to minimize the energy cost and the quantities of by‐products for a poly(ethylene terephthalate) process by using the iterative dynamic programming (IDP) algorithm. Here, we employed a sequence of three reactor models: the semibatch transesterification reactor model, the semibatch prepolymerization reactor model, and the rotating‐disc‐type polycondensation reactor model. We selectively chose or developed the reactor models by incorporating experimentally verified kinetic models reported in the literature. We established the model for the entire reactor system by connecting the three reactor models in series and by resolving some joint problems arising when different types of reactor models were interconnected. On the basis of the simulation results of the reactor system, we scrutinized the cause and effect between the reaction conditions and the final quality of the polymer product. Here, we set up the optimization strategy by using IDP on the basis of the integrated reactor model, and the process variables with significant influence on the properties of polymer were selected as control variables with the help of a simulation study. With this method, we could refine the reaction conditions at the end of each iteration step by contracting the spectra of control regions, and the iteration process finally stopped when the profile of the optimal trajectory converged. We also took the constraints on the control variables into account to guarantee polymer quality and to suppress side reactions. Constituting six different strategies by setting weighting vectors differently, we examined the differences in optimal trajectories, the trend of optimality, and the quality of the final polymer product. For each of the strategies, we conducted the optimization to examine whether the number‐average degree of polymerization approached the desired value. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 993–1008, 2002