侧链为亚乙氧基结构的EVOH梳型聚合物的合成

以乙烯-乙烯醇共聚物(EVOH)为原料，制备了一种主链为疏水的聚乙烯链段，侧链具有亚乙氧基结构的多羟基梳形聚合物，用元素分析法、凝胶渗透色谱法、核磁共振谱法对其进行了结构表征；用热重分析法和示差扫描量热法对其热学性能进行了表征。结果表明，接枝后产物的玻璃化转变温度在-52--40℃之间，熔点在55～600℃之间，由于侧链的引入破坏了EVOH的结晶，因此梳形聚合物的热分解温度比EVOH降低了约20℃。     

Polyaniline as corrosion inhibitor for iron in acid solutions

In recent years, polymer amines have been studied as an efficient corrosion inhibitor for iron in acid media. In this article, the performance of water soluble polyaniline as corrosion inhibitor for iron in 0.5M H₂SO₄ has been evaluated by potentiodynamic polarization, linear polarization, and electrochemical impedance spectroscopy and compared with the performance of the aniline monomer. It has been found that polyaniline is an efficient inhibitor, since the maximum efficiency of 84% has been observed at a concentration of 100 ppm, whereas the monomer has accelerated the corrosion. FTIR studies have shown that the polyaniline is strongly adsorbed on the iron surface and inhibits the corrosion effectively. However, aniline has been found to improve the passivation tendency of iron at higher concentrations. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 2144–2153, 2006     

Effect of incipient removal of hydrogen through palladium membrane on the conversion of methane steam reforming: Experimental and modeling

This paper presents a mathematical model based on the reaction rate expressions to describe the displacement of methane conversion in the steam reforming. The effect of several parameters including weight hourly space velocity (WHSV), load-to-surface ratio, reaction pressure, hydrogen partial pressure in permeate side and reaction temperature were investigated. Simulation and experimental results showed that a conversion higher than 80% could be achieved in a palladium membrane reactor at reaction temperature of 500 °C relative to 850 °C in a conventional fixed bed reactor (FBR). Besides, the yield of CO (<2%) in membrane reactor was much lower than that (>50%) in the FBR, which indicated the significant depression of CO production in use of membrane reactor.     

Mechanosynthesis of complex oxides and preparation of mixed conducting nanocomposites for catalytic membrane reactors

Nanopowders of LaGaO₃- and LaMnO₃-based complex perovskites (P) and ceria-based fluorites (F) were prepared by mechanosynthesis. Compatible nanocomposites F + P and P + P with mixed ion and electron conducting (MIEC) properties were prepared and sintered at moderate temperatures up to dense ceramics. The obtained materials were studied by means of XRD, SEM, TEM, electrical conductivity measurements, temperature programmed (TP) reduction/oxidation and preliminary estimations of permeability were obtained. A new strategy based on the advantages of the mechanochemical ceramic approach is proposed to design multilayer ceramic membranes for CMR. Casting technology and one-step sintering were used for the production of thin film membranes with MIEC properties on porous substrates. The coarse fraction of as-milled powders from agglomerates with density 70% was used for the porous substrate, and fine fractions of aggregates with sizes <1 μm were used in preparation of composites for thin dense films. Ceria-based composites prepared by the Pechini route and/or mechanochemical method are proposed as materials for protecting thin films.     

Lithium/V6O13 cells using silica nanoparticle-based composite electrolyte

The electrochemical behavior of Li/V₆O₁₃ cells is investigated at room temperature (22 °C) both in liquid electrolyte consisting of oligomeric poly(ethyleneglycol)dimethylether+lithium bis(trifluoromethylsulfonylimide) and composite electrolytes formed by blending the liquid electrolyte with silica nanoparticles (fumed silica). The addition of fumed silica yields a gel-like electrolyte that demonstrates the desirable property of suppressing lithium dendrite growth due to the rigidity and immobility of the electrolyte structure. The lithium/electrolyte interfacial resistance for composite gel electrolytes is less than that for the corresponding base-liquid electrolyte, and the charge-discharge cycle performance and electrochemical efficiency for the Li/V₆O₁₃ cell is significantly improved. The effect of fumed silica surface group on the electrochemical performance is discussed; the native hydrophilic silanol surface group appears better than fumed silica that is modified with a hydrophobic octyl surface moiety.     

Preparation of micro-patterned surfaces of Si-N-O films and their influence on adhesion behavior of endothelial cells

Microgrooves were prepared on Si(100) surface by photolithography and wet etching.Subsequently,Si-N-O films were deposited on the microgrooves by unbalanced magnetron sputtering(UBMS) and micro-patterned surfaces of Si-N-O films were obtained.The size of the micropatterns was measured by surface profilometer.The chemical composition of Si-N-O films were characterized by X-ray photoelectron spectrometry(XPS) and the wettability of the micropatterned surfaces was evaluated by contact angle measurement.The beh...     

米曲霉在牛乳中最适生长条件的研究

利用米曲霉对牛乳进行发酵,通过单因子及正交试验以菌丝体干重为指标对其在牛乳中的生长进行了研究．结果表明：接种量为4％,装液量为30mL,摇床转速为180r／min时菌丝体干重可达到最大．此外测得最大菌丝体干重时的蛋白质分解率可达35．6％．     

Milled fibre reinforced epoxy resin — an engineering polymer composite

A milled fibre reinforced epoxy resin composite (MFRE) has been developed for low temperature use. It is resistant to fracture at temperatures down to at least 77 K in direct contact with liquefied gases. It can be used as an adhesive, a gap-filling mastic or a moulding compound for difficult cryogenic applications. The characteristics of the material and some applications are described.     

Highly ion-conductive solid polymer electrolytes based on polyethylene non-woven matrix

Highly ion-conductive solid polymer electrolyte (SPE) based on polyethylene (PE) non-woven matrix is prepared by filling poly(ethylene glycol) (PEG)-based crosslinked electrolyte inside the pores of the non-woven matrix. The PE non-woven matrix not only shows good mechanical strength for SPE to be a free-standing film, but also has very porous structure for high ion conductivity. The ion conductivity of SPE based on PE non-woven matrix can be enhanced by adding sufficient non-volatile plasticizer such as poly(ethylene glycol) dimethyl ether (PEGDME) into ion conduction phase without sacrificing mechanical strength. SPE with 20 wt.% crosslinking agent and 80 wt.% non-volatile plasticizer shows 3.1 × 10⁻⁴ S cm⁻¹ at room temperature (20 °C), to our knowledge, which is the highest level for SPEs. It is also electrochemically stable up to 5.2 V and has high transference number about 0.52 due to the introduction of anion receptor as an additive. The interfacial resistance between Li electrode and SPE is low enough to perform charge/discharge test of unit cell consisting of LiCoO₂/SPE/Li at room temperature. The discharge capacity of the unit cell shows 87% of theoretical value with 86% Coulombic efficiency.