两亲性聚合物多孔微球的制备研究

合成了具有悬挂双键的苯乙烯-二乙烯基苯多孔微球,在悬挂双键处接枝甲基丙烯酸甲酯,制成了一系列不同接枝度的两亲性聚合物多孔微球。考察了悬挂双键数量、反应时间等因素对接枝率的影响以及接枝率对微球形貌的影响。实验中通过观测澄清点,有效地控制了反应后期自加速现象对接枝率的影响。在反应时间25 m in时,制得了平均孔径为50 nm的两亲性多孔微球。将该微球用于对化妆品活性组分的负载,对极性物的负载率比接枝前高出2倍。     

Numerical study of the transfer of shock-wave loading to a screened flat wall through a layer of a powdered medium and a subsequent air gap

The two-velocity, two-temperature model with two stresses in a mixture of a gas and solid particles contacting each other is used to numerically study the dynamic effect of an air shock wave incoming onto a solid wall with a screening layer of a porous powdered medium at some distance from the wall. The process is described for the case of one-dimensional planar motion of the gaseous and disperse phases under the assumption of a viscoelastic behavior of the powder skeleton. The effect of stepwise shock waves onto the porous powdered screen is considered. The influence of parameters of the screening layer and the air gap on the dynamics of loading of the screened solid wall is analyzed. __________ Translated from Fizika Goreniya i Vzryva, Vol. 43, No. 1, pp. 132–142, January–February, 2007.     

STUDIES ON COUNTERACTING CHROMATOGRAPHIC ELECTROPHORESIS AND ITS UTILIZATION FOR PROTEIN PURIFICATION

A counteracting chromatographic electrophoresis(CACE)separation device has been success-fully built and tested.Experiments are performed with protein mixtures of BSA,Hg,Mg and Cyto-cto study the separation performances,concentration profiles,start-up methodology as well as influ-ences of pH and ionic strength on the separation process.Mathematical models based on the fluiddynamics of the porous medium are proposed.Experiments indicate that the CACE process has agood commercial potential in protein engineering and fine chemicals purification.     

组织工程多孔支架制备技术进展

综述了天然或合成生物降解材料为原料的组织工程多孔支架的几种制备方法，包括无纺织物／纤维粘结法、溶液浇铸／粒子洗出法、相分离／冻干法、气体成孔法和三维“印刷”等方法。特别评述了近期组织工程多孔支架研究进展及其在骨、软骨和皮肤等组织修复中的应用。     

致孔剂溶胀法制备多孔结构的乳胶粒

以苯乙烯、二乙烯基苯为单体 ,在传统乳液聚合阶段引入甲苯和庚烷作为单体的混合溶剂 (致孔剂 ) ,使溶剂在聚合中进入乳胶粒子内部 ,聚合完成后 ,通过水蒸气蒸馏的方法将致孔剂带出 ,以形成多孔结构乳胶粒。本文考察了单体和致孔剂比例、致孔剂中甲苯和庚烷的比例对反应速率、单体转化率及多孔结构乳胶粒的影响 ,结果表明 :单体和致孔剂比例为 2∶1、致孔剂中甲苯和庚烷的比例为 2∶1时 ,能够得到清晰结构多孔乳胶粒。     

双电层电容器用多孔炭材料的研究与开发

阐述了双电层电容器的工作原理，探讨了多孔炭材料的比表面积、孔径分布、表面官能团、表面石墨微晶取向、体积密度和电导率以及电化学稳定性等微孔结构与物理化学性质对其电容特性的影响，介绍了近年来用作双电层电容器电极的几种新型多孔炭材料的研究进展。     

颗粒多孔表面强化沸腾传热动力学研究

通过对颗粒多孔层几何结构、沸腾两相流及传热的理论分析，提出了微型通道薄膜环状蒸发物理模型和沸腾传热机理，建立了颗粒多孔表面强化沸腾传热动力学模型。该动力学模型与实验数据吻合良好，可用于工程设计。     

Matching ratio between positive and negative electrodes for double-layer capacitors

For double-layer capacitors in alkaline electrolyte, the specific capacitance of the positive electrode is not equal to that of the negative one. Thus, capacitor performance cannot be optimal with a positive/negative electrode matching ratio of 1. In this study nanoporous glassy carbons (NPGCs) were employed as the electrodes of capacitors, and the influence of matching ratio between positive and negative electrode on capacitor performance was systematically investigated. In aqueous KOH, the specific capacitance of the positive electrode is lower than that of the negative electrode. The matching ratio at which a maximum capacitance is obtained is dependent on the values of the positive and negative electrode capacitance. At low current rate, the highest specific capacitance is achieved at a matching ratio slightly higher than 1. At high current rate, a capacitor has the highest specific capacitance with the lowest resistance at a matching ratio of 1.5. This indicates that an optimum matching relationship between positive and negative electrodes is attained.     

Novel Method To Optimize the Structure of Reticulated Porous Ceramics

A novel method has been developed for the fabrication of silicon nitride reticulated porous ceramics (RPCs) with regulated structure, using polyurethane sponge as the template. This technique includes two centrifuging steps. In the first stage, the polyurethane sponges are coated with thin slurry through high-speed centrifuging. After the slurry on sponges dried, a high-strength green body without filled cells is obtained. In the second stage, because of improved adhesion between the body and the slurry after the first coating, the body with uniformly thick strut is produced by recoating the as-prepared green body with thixotropic slurry and centrifuging again. The loading content of slurry and the pore diameter of the RPCs body greatly depend on the slurry viscosity in the process of recoating. The strut diameter and pore diameter of the RPCs are effectively optimized by modulating the slurry viscosity.     

油水乳液分离吸附材料的分离原理、构建方法和分离性能

采用吸附材料进行油水分离是经济且非常有效的方法。吸附材料主要有无机材料、合成高分子材料和天然有机纤维材料等。相比较而言，天然有机纤维材料为可再生生物质资源，来源广泛、生物降解性好，可有效防止二次污染，具有良好的发展潜力，备受关注。本文首先简要介绍了油水乳液稳定性的影响因素，然后综述了油水分离材料的分离原理、构建方法和分离性能等研究进展，并总结了油水乳液分离材料的表征及其分离性能的评价指标。特别地，重点总结了天然有机纤维基吸附材料分离油水乳液的研究进展。最后指出研究智能响应型天然有机纤维基油水乳液分离吸附材料是重要的发展方向。