炭黑填充硬聚氯乙烯的改性

为使聚氯乙烯具有抗静电性能,采用加入具有导电性填料的方法,但加入大量的填料,会使硬聚氯乙烯的冲击性能降低,加工性能变差。本文是在以炭黑为填料的基础上,研究不同的改性剂和加工助剂改进硬聚氯乙烯的效果,结果表明,加入冲击改性剂和加工助剂后,大大增加了硬聚氯乙烯的冲击强度,且加工性能也得到改善,同时由于炭黑具有补强效果,其拉伸强度和弯曲强度在加入改性剂后也能满足使用要求。     

炭分子筛概述

阐述了炭分子筛分离的原理，并分别从其制备原料、制备方法、产品用途等方面综述了近年来炭分子筛的新进展。     

无水焦粉粉尘治理工艺改造及综合利用

简述了无水焦粉生产过程中的粉尘污染及其危害，分析了目前粉尘污染的现状、研究情况、环境监测及改造的必要性，提出了解决无水焦粉粉尘治理工艺改造的方案及粉尘的综合利用。     

改性活性炭的表面特性及其对苯酚的吸附性能

研究了表面改性对活性炭吸附苯酚性能的影响。研究发现,硫酸氧化可增加活性炭表面酸性基团的含量,提高了活性炭的表面亲水性,降低pHPZC值,因而对吸附水中的苯酚的性能产生明显影响,降低了对苯酚的吸附。     

Morphologies and microstructures of tree-like carbon produced at different reaction conditions in a CVD process

Centimeter-size multi-branched tree-like carbon structures have been generated by the catalytic chemical vapor deposition of toluene using ferrocene as the catalyst precursor and investigated by means of SEM, TEM, and EDX. It is found that a temperature of 1000-1200 °C and a carrier gas flow rate of 1000-2500 ml/min are necessary for the generation of the carbon trees. Their morphologies and microstructures change greatly with the changing reaction conditions. The fractal dimensions of the trees are calculated to quantitatively investigate the influence of different reaction temperatures on the morphologies.     

改良MEA脱碳技术在小氮厂变换气脱碳中的应用

介绍了改良MEA脱碳技术的基本原理、工艺特点以及在工业中的应用情况，实践表明，改良MEA提高了溶液的吸收能力，降低了再生热耗，解决了MEA易降解损耗等问题。     

真空粉末绝热低温贮罐制造的部分工艺方法

在真空粉末绝热低温贮罐的制造过程中、通过吸附器分子筛的活化、夹层真空系统的处理和充装珠光砂等工艺方法的改进,可较大地缩短产品的制造周期并提高产品的质量。     

Preparation of phenolic resin derived 3-D ordered macroporous carbon

Three-dimensionally ordered long-range macroporous carbon structures were prepared using commercially available phenolic resin by utilizing sacrificial colloidal silica crystalline arrays as templates that were subsequently removed by HF etching after pyrolysis in an argon atmosphere. SEM, TEM, and BET were employed to characterize the morphology and the surface area of the porous carbon structures. The pore size (150–1000 nm) and BET surface area, which reflect pore volume (298.6 m²/g (1.32 cm³/g) ∼ 93.7 m²/g (0.12 cm³/g)), of the macroporous carbon structures produced were approximately proportional to the size (150–1000 nm) of the sacrificial silica sphere templates used (annealing temp. 550°C). The achieved 550 nm porous carbon structures were examined to function as potential catalyst carriers and were successfully impregnated with Ag or Pt-Ru on their inner walls after borohydride reduction at room temperature. In addition, porous carbon patterns were fabricated using the ‘micromolding in capillary’ technique, which has potential applications in the microreaction technology.     

Supported Vanadia Catalysts for Dehydrogenation of Ethylbenzene with CO2

Alumina supported vanadia catalysts (V/Al) for selective oxidehydrogenation of ethylbenzene with CO₂ were prepared by impregnation method. During preparation the effect of promoters and calcined temperature was investigated, it was found these two items had a strong influence on the activity of V/Al catalysts. Dehydrogenation reaction with CO₂ was happened in the fixed-bed reactor at 450 °C. Results showed that 15.2% ethylbenzene conversion and 99.2% styrene selectivity were acquired when V₂K/Al catalyst was used.     

Concentration of tocopherols from soybean sludge by supercritical carbon dioxide

A supercritical fluid extraction method has been applied to test the feasibility of tocopherol concentration from soybean sludge with carbon dioxide at temperatures and pressures ranging from 35 to 70°C and 200 to 400 bar, respectively. The supercritical solubility of the esterified soybean sludge was over 4–6 times greater than that of the original soybean sludge. By a simple batch-type one-stage method the tocopherols in the esterified soybean sludge could be concentrated up to 40 wt%. The overall results of the present study show that soybean sludge initially containing about 13–14 wt% tocopherols may require a countercurrent multistage column to be highly and effectively concentrated.