电站锅炉制粉系统的爆炸原因与防范对策

火力发电厂制粉系统爆炸事故时有发生 ,重大设备损坏 ,造成了严重的经济损失。本文通过分析研究 ,找出制粉系统爆炸的原因 ,从措施上、煤的质量控制上及制粉系统结构改造上提出了防范的对策。     

控制图在土坝粘土填筑干密度控制中的应用

应用统计控制图法，选用平均值——标准差、平均值——极差控制图法，控制24^#坝粘土填筑干密度值及施工偶然异常波动，早期提出警报，以保证土坝的施工质量。     

Preparation and properties of novel polyurethane insulating coatings based on glycerin‐terminated urethane prepolymers and blocked isocyanate

Novel polyurethane insulating coatings were prepared from the reaction of glycerin‐terminated polyurethane prepolymers (GPUPs) and a blocked isocyanate curing agent (BIC). The GPUPs were prepared from the reaction of one equivalent of polycaprolactone polyol (CAPA 210) with an excess amount of 4,4′‐methylene bis(phenyl isocyanate) (MDI) and subsequent reaction of the NCO‐terminated polyurethane with glycerin. The BIC was prepared from the reaction of trimethylol propane (TMP), toluene diisocyanate (TDI) and N‐methylaniline (NMA). The polyols and curing agent were characterized by conventional methods while the curing condition was optimized via gel content measurements. The curing kinetics of the polyurethane coating were investigated and the kinetic parameters derived. The crosslink densities of the samples were determined via the equilibrium swelling method, using the Flory–Rehner equation. The relationships between the crosslink density and the electrical, physical, mechanical and dynamic mechanical properties of the coatings were also studied. Copyright © 2005 Society of Chemical Industry     

Low density polyethylene and grafted lignin polyblends using epoxy‐functionalized compatibilizer: mechanical and thermal properties

Lignin was graft copolymerized with methyl methacrylate using manganic pyrophosphate as initiator. This modified lignin was then blended (up to 50 wt%) with low density polyethylene (LDPE) using a small quantity of poly[ethylene‐co‐(glycidyl methacrylate)] (PEGMA) compatibilizer. The mechanical properties of the blend were substantially improved by using modified lignin in contrast to untreated lignin. Differential scanning calorimetry studies showed loss of crystallinity of the LDPE phase owing to the interaction between the blend components. Thermogravimetric analysis showed higher thermal stability of modified lignin in the domain of blend processing. This suggested that there is scope for useful utilization of lignin, which could also lead to the development of eco‐friendly products. Copyright © 2005 Society of Chemical Industry     

探讨电石法PVC烟气治理方法

分析了电石法PVC生产链中电石炉烟气及电厂烟气二氧化硫的排放情况,指出利用电石炉烟气中的CO合成氨、再将合成氨用于燃煤电厂烟气的"氨法"脱硫是具有较大应用潜力的循环经济产业链。     

The influence of raw material characteristics on the industrial pelletizing process and pellet quality

Industrial pelletizing of sawdust was carried out as a designed experiment in the factors: sawdust moisture content, fractions of fresh pine, stored pine and spruce. The process parameters and response variables were energy consumption, pellet flow rate, pellet bulk density, durability and moisture content. The final data consisted of twelve industrial scale runs. Because of the many response variables, data evaluation was by principal component analysis of a 12 × 9 data matrix. The two principal component model showed a clustering of samples, with a good reproducibility of the center points. It also showed a positive correlation of energy consumption, bulk density and durability all negatively correlated to flow rate and moisture content. The stored pine was more related to high durability and bulk density. The role of the spruce fraction was unclear. The design matrix, augmented with the process parameters was a 12 × 6 matrix. Partial least squares regression showed excellent results for pellet moisture content and bulk density. The model for durability was promising. A 12 × 21 data matrix of fatty- and resin acid concentrations measured by GC–MS showed the differences between fresh and stored pine very clearly. The influence of the spruce fraction was less clear. However, the influence of the fatty- and resin acids on the pelletizing process could not be confirmed, indicating that other differences between fresh and stored pine sawdust have to be investigated. This work shows that it is possible to design the pelletizing process for moderate energy consumption and high pellet quality.     

3-D MCM封装技术及其应用

介绍了超大规模集成电路（VLSI）用的3-D MCM封装技术的最新发展，重点介绍了3-D MCM封装垂直互连工艺，分析了3-D MCM封装技术的硅效率、复杂程度、热处理、互连密度、系统功率与速度等问题，并对3-D MCM封装的应用作了简要说明。     

粉煤灰降失水水泥浆在天然气井固井中的研究与应用

长庆天然气田属于低压、低渗透气田,存在承压能力较低的地层,固井设计要求全井段封固,并且采用双级双凝施工工艺。但由于用于低密度水泥浆中的漂珠生产量降低,价格上升,研究应用替代产品是固井技术发展的方向。在一级领浆中研究应用了粉煤灰水泥浆体系,其性能和固井质量可完全满足固井要求。粉煤灰水泥浆体系价格低和固井质量优良,使其成为漂珠水泥浆体系的替代配方。     

The Minimum PAPR Code for OFDM Systems

In this letter, a block code that minimizes the peak‐to‐average power ratio (PAPR) of orthogonal frequency division multiplexing (OFDM) signals is proposed. It is shown that peak envelope power is invariant to cyclic shift and codeword inversion. The systematic encoding rule for the proposed code is composed of searching for a seed codeword, shifting the register elements, and determining codeword inversion. This eliminates the look‐up table for one‐to‐one correspondence between the source and the coded data. Computer simulation confirms that OFDM systems with the proposed code always have the minimum PAPR.     

Carbon nanofibers as hydrogen adsorbing materials for power sources

Porous carbon nanofibers are synthesized by CVD method from acetylene with use of iron-containing catalysts. Activation of the nanofibers in melted potassium hydroxide results in increasing surface area from initial 300–400 m² g⁻¹ to 1700 m² g⁻¹. As follows from XRD data, activated nanofibers do not contain regular packages of graphene layers, but retain high electric conductivity. Deposition of copper improves electrochemical hydrogen storing characteristics of carbon nanofibers. Carbon nanomaterials obtained can be used as hydrogen storing materials in batteries instead of hydride forming metals.