Fe3Al/Q235异种材料扩散焊界面相结构分析

采用X射线衍射、透射电镜和电子衍射技术对Fe3Al/Q235真空扩散焊界面附近的微观相结构进行了试验研究。试验结果表明，当加热温度1050～1080℃，保温时间60min，压力9.8MPa时，Fe3Al金属间化合物与Q235钢扩散焊界面附近形成了明显的扩散过滤区，该过渡区由Fe3Al相和a-Fe(Al）固深体构成，显微硬度约为480～540HM，不存在含铝校较高的高硬度脆性相。有利于提高Fe3Al/Q235扩散过滤区的韧性，提高扩散焊接头的抗裂纹能力。扩散过滤区中的Fe3Al相与a-Fe(Al）固溶体之间存在着（110）a-Fe(Al)//(011)Fe3Al和[001]a-Fe(Al)//[100]Fe3Al的晶体学取向关系。     

原位生成Al2O3、TiB2和Al3Ti/Al复合材料的热循环行为

本文研究了Al-TiO2-B系原位生成Al2O3、TiB2和Al3Ti/Al颗粒增强铝基复合材料的热循环行为，研究结果表明了纯铝及B／TiO2摩尔比分别为0、1和2的颗粒增强铝基复合材料的热循环行为具有以下结果，纯铝和复合材料热循环后均产生了残余应变和滞后环；Al-TiO2-B系列复合材料热循环应变的各项指标均比纯铝基体大大降低，且具有较小的内耗功和较好的热稳定性，可以预测其具有较高的热疲劳寿命，热循环曲线能很好的评估复合材料在温度循环变化的环境中工作时的热稳定性和热疲劳。     

Behavior of laser welded steel in chloride solution studied using difference imaging

In situ imaging techniques in conjunction with electrochemical measurements were used to study the behavior of steel surfaces in simple chloride solutions. The imaging method detected the presence of significantly thicker uniform layers than the original passive oxide. The layers were found to form in chloride after the steel was anodically polarized following reduction of the passive oxide film. The growth of the layer depended on the degree of prior passive oxide reduction. Formation of the layer was also sensitive to underlying structure and enabled rapid location of regions of higher corrosion rate across laser welds in steels.     

氧化合成对羟基苯甲醛的研究

研究了在硫酸介质中用Mn3+氧化对甲苯酚合成对羟基苯甲醛适宜的工艺条件:反应温度50℃,反应时间60 m in,硫酸浓度7.0 mol/L,搅拌速度为600 r/m in。粗产品经多步过滤分离法提纯,其总产率可达64.63%。     

Polymorphism of tricalcium silicate, the major compound of Portland cement clinker: 2. Modelling alite for Rietveld analysis, an industrial challenge

A comprehensive quantification of the various phases of clinkers by X-ray diffraction with a Rietveld-like analysis is an important industrial challenge. Various available structural models are used for the most frequent M1 and M3 polymorphs of alite usually found in industrial clinkers, referred to as M1- or M3-based clinkers. In this paper, the effect of C₃S structural model is investigated. Four models are tested and compared using either synthetic M1 and M3 alites or M1- and M3-based clinkers. The comparison validates the available models for M1 and M3 alites and an average model, given here, derived from our recently proposed M1 structure as a catch-all model when the nature of the clinker is unknown. The latter model is meant to be used for industrial on-line quantification.     

不同分散染料微胶囊的制备及应用

采用原位聚合法进行双层造壁，对不同结构的分散染料进行胶囊化。将分散染料高速均化后，在pH=4～6时加入TMM，65℃保温1．5小时，再滴加一定量PEHMM，在75℃时保温2.5小时进行双层造壁、C.I.分散橙30染料胶囊的粒径平均值为13．53μm，中值8．732μm；C.I．分散蓝56微胶囊粒径平均值为36.3μm，中值24.87μm。胶囊染色结果显示：这两只染料性能优于传统染料，染色后其废液的吸光度分别为0.021和0.003，比传统染色废水的1.286和0.786低很多。     

异丁醛合成2,4,6-三异丙基-1,3,5-三噁烷的研究

本文以异丁醛为原料在杂多酸催化剂的作用下，环化合成了无毒升华剂2，4，6－三异丙基－1，3，5－三恶烷，考查了各种反应条件的影响，确定以磷钨酸为催化剂时的最佳反应条件：反应温度25℃，催化剂用量1．5％，反应时间2．5h，产物的收率达84％以上。     

纳米CaCO3的表面改性研究

本文研究了纳米CaCO3表面改性的影响因素，确定了最优改性剂和改性条件，并运用沉降实验、透射电镜（TEM）等表征手段对粉体的改性效果进行了分析。结果表明：以月桂酸钠为改性剂，用量为10％，pH值为7，改性时间为1h时，改性后的纳米CaCO3的亲油化度达到85．1％，能较好地分散于环己烷和二甲苯中。     

纳米四氧化三铁磁性微粒的表面有机改性

通过液相共沉淀法制备了纳米四氧化三铁溶胶，利用油酸对纳米粒子体进行表面改性和萃取实验，获得油酸包覆的四氧化三铁微粒。采用FT—IR和高分辨透射电镜对改性后的纳米粉体进行结构和形貌的表征。研究结果表明油酸与四氧化三铁纳米粒子间存在化学键结合。油酸对纳米四氧化三铁微粒进行改性，并且对纳米粒子进行包覆，使外表面形成保护层阻止粒子团聚，改性后的四氧化三铁微粒与有机物具有良好的相溶性，采用表面改性显著改善了纳米四氧化三铁微粒的性能指标。     

Oxygen transport in ferrite-based ceramic membranes: Effects of alumina sintering aid

Moderate additions of Al₂O₃ to strontium ferrite-based mixed conductors, such as SrFe_0.7Al_0.3O_3−δ and La_0.2Sr_0.8Fe_0.8Ga_0.2O_3−δ with the composition close to the solid solution formation limits, make it possible to improve ceramics sinterability, to increase oxygen permeability and to decrease thermal expansion. These effects are associated with the segregation of alumina-rich phases, primarily SrAl₂O₄, and the formation of A-site cation-deficient perovskite. The improved properties of the SrFe_0.7Al_0.3O₃-based material were used to fabricate high-quality tubular membranes for methane conversion reactors. Similar enhancement in sinterability is also observed for another promising parent material of mixed-conducting membranes, La_0.5Sr_0.5FeO_3−δ. However, extensive dissolution of Al³⁺ cations in the iron sublattice, creation of A-site vacancies and changing the La:Sr concentration ratio all lead to decreasing ionic transport in La_0.5Sr_0.5FeO_3−δ. As a result, additions of either Al₂O₃ or SrAl₂O₄ have a deteriorating influence on the oxygen permeation fluxes through La_0.5Sr_0.5FeO₃-based ceramics.