橡胶密炼机混炼工艺瞬时功率控制法

橡胶密炼机混炼工艺瞬时功率控制法的理论由３部分组成：橡胶混炼过程的机理、密炼机流理论和混炼过程功率曲线与能量控制法不同，瞬时功率控制法实质上是控制混炼过程中胶料的粘度，确保混炼工艺过程保持最佳状态。因而瞬时功能控制法可监控生产过程，为密炼机混炼工艺的智能控制奠定了基础。     

剪切型调距式密炼机的性能研究

对啮合型、剪切型和剪切调距型3种密炼机的混烁实验结果进行了比较分析,对剪切调距型密炼机的性能进行了研究,实验表明：新开发的剪切型调距式密炼机能够混炼均匀,分散度高,能量消耗少,排胶温度低,可通过改变间隙实现优化混炼,尤其适合于快速混烁作业和难以分散而又快速生热的胶料的混烁,应用前景比较广淘.     

过磷酸钙折流混合器的改进

由于绿原化工有限公司过磷酸钙装置生产能力由 6 70 t/ d(实物量 )提高到 84 0 t/ d,折流混合器负荷增大 ,出现折流环磨损加快等问题。采用若干技改措施 :扩大折流环内径、改变折流混合器喷射方向、采用新材料制作折流环 ,使折流混合器能满足 84 0 t/ d过磷酸钙生产的需要     

双工质塑料冷混机设计研讨

介绍了可提高塑料混合时冷却效率的双工质塑料冷混机，并简要叙述了立式，卧式和立式搅龙双工质冷混机却装置冷却物料的工序。     

Single frame correction of motion artifacts in PMD-based time of flight cameras

One of the leading time of flight imaging technologies for depth sensing is based on Photonic Mixer Devices (PMD). In PMD sensors each pixel samples the correlation between emitted and received light signals. Current PMD cameras compute eight correlation samples per pixel in four sequential stages to obtain depth with invariance to signal amplitude and offset variations. With motion, PMD pixels capture different depths at each stage. As a result, correlation samples are not coherent with a single depth, producing artifacts. We propose to detect and remove motion artifacts from a single frame taken by a PMD camera. The algorithm we propose is very fast, simple and can be easily included in camera hardware. We recover depth of each pixel by exploiting consistency of the correlation samples and local neighbors of the pixel. In addition, our method obtains the motion flow of occluding contours in the image from a single frame. The system has been validated in real scenes using a commercial low-cost PMD camera and high speed dynamics. In all cases our method produces accurate results and it highly reduces motion artifacts.     

Polyacrylonitrile/Nylon 6 Blends: Preparation and Characterization

Summary: Polyacrylonitrile (PAN) particles with micro‐size ranges (0.15–2 μm) were prepared by emulsion and dispersion polymerizationa and in supercritical carbon dioxide media. The PAN particles were blended with Nylon 6 (PA6) at 220 °C by using a miniature mixer; it was found that melt‐mixing was possible for PAN‐rich compositions as high as 70 wt.‐%. Blends were characterized by scanning electron microscopy, IR, viscosity measurements, differential scanning calorimetry, and dynamic mechanical thermal analysis (DMTA). The size and shape of original PAN particles were retained in PAN/PA6 blends. The useful range to blend PAN particles size was less than 1 μm in terms of shape retention of the PAN particles in blends. Blends with 40 wt.‐% PAN content were found to be melt‐processable. The elastic modulus was higher for PAN/PA6 blends than pure PA6.

SEM photograph of PAN‐SC/PA6 blend with a 40/60 weight ratio.     

密炼机转子铜瓦椭圆的修复方法

简要介绍了一种XHM253/20密闭式炼胶机转子铜瓦椭圆的修复方法.该方法简便易行,修复工期短,修复质量高,在实际工作中具有一定参考价值.     

油水气三相流液体流量调节系统研究与设计

针对油水气三相流研究试验平台液体流量调节范围宽、范围度大的问题,提出采用3条主回路与3条旁通回流调节支路来覆盖所有的流量范围,设计了液相系统原理图及管路布置图,对3条旁通回流调节支路中调节阀的计算流量、计算压差及Kv值进行了计算,并对调节阀的开度及实际可调比进行了验算,结果表明选定的调节阀性能满足油水气三相流研究试验的要求。     

剖析F型、GK型密炼机结构特征

目前，以美国F型和德国GK型为代表的密炼机已在我国基本上实现了国产化。对这两类密炼机的结构特点和安装、使用上的利与弊，本文从密炼装置、转子密封装置、卸料装置、锁紧装置到主传动5个方面作了详细的剖析，并在此基础上，提出一个取长补短的新的密炼机设计方案。     

静态混合器气液两相流压降的数值模拟及实验研究

气泡流经过静态混合器的压降问题涉及到舰船动力系统性能的好坏。在分析了气泡平均驰豫时间的基础上,结合k ε湍流模型,利用平衡流模型模拟静态混合器内形成的稀疏湍流气泡流,得到了混合器内两相流流场。空气—水系统的压力降实验表明,计算流体力学模拟能够很好地预测SMV型静态混合器内气泡流的压降,是静态混合器设计的有效手段。