Phase Composition of Oxide Scales during Reheating in Hot Rolling of Low Carbon Steel

Low carbon steel was oxidized over the temperature range 1000‐1250°C in O₂‐CO₂‐H₂O‐N₂, O₂‐H₂O‐N₂, and O₂‐CO₂‐N₂ gas mixtures. Oxidation times were 12‐120 min. and the scales were 50‐2000 μm thick. The variations of these parameters were chosen to elucidate the phase composition of oxide scales under conditions similar to those of reheating furnaces in hot strip mills, using either thin slab casting or conventional casting and rolling technology. Two types of scales have been observed which are influenced by the furnace atmosphere, oxidation time, and temperature. The first type is a crystalline scale with an irregular outer surface, composed mostly of wustite (FeO), and a negligible amount of magnetite (Fe₃O₄). The second type is the classical three‐layer scale, composed of wustite (FeO), magnetite (Fe₃O₄), and hematite (Fe₂O₃). In general, the experiments showed that an increase in oxidation time decreased the percentage of wustite while the percentages of magnetite and hematite increased. A rise in oxygen concentration in the gas mixture increased the percentages of magnetite and hematite, confirming earlier experimental findings. In water vapour‐free atmospheres O₂‐CO₂‐N₂, the oxide scales had a low percentage of wustite, and high percentage of magnetite and hematite. Carbon dioxide showed a small influence at 1100°C, and a negligible one at 1250°C.     

基于遗传算法的工作辊温度场参数优化模型

针对热连轧机工作辊热辊形计算中温度场模型的热交换等参数难以确定的问题 ,建立了基于遗传算法的参数优化模型 ,可以解决复杂条件下的热参数的求解问题。利用优化参数计算的轧辊温度场与实际测量结果一致。     

轧后穿水冷却工艺对棒材组织性能的影响

针对轧机产量提高后冷床冷却能力不足的问题 ,研制开发了棒材轧后穿水冷却技术。通过对小规格 2 0MnSiV热轧带肋钢筋进行轧后穿水冷却 ,钢材上冷床温度降低了 90～ 110℃ ,提高了产品质量 ,改善了各项力学性能 ,抗拉强度平均提高了 3 5～ 40MPa ,钢材性能合格率由 97.5 %提高到了 99.6% ,解决了冷床冷却能力不足、制约生产的瓶颈问题。     

The Influence of Medium on Low-Voltage Circuit Breaker Arcs

This paper mainly focuses on the influence of three kinds of media： air, air-10%PA （Nylon） and air-10% POM （polyoxymethylene） on low-voltage circuit breaker arcs. A threedimensional （3-D） model of arc motioa under the effect of external magnetic field is built based on magnetohydrodynamics （MHD） equations. By adopting the commercial computational fluid dynamics （CFD） package based on the control-volume method, the above MHD equations are solved. For the media of air-10%PA and air-10%POM, the distributions of stationary temperature and electrical potential and the transient motion processes are compared with those of air arc. The research shows that both air-10%PA and air -10% POM can cool the arc plasma and the former is more effective. Both of them can increase the stationary voltage as well. Moreover, the presence of the two mixtures can accelerate the arc motion toward the quenching area and ensures the arc quenched in time.     

Q195冷轧板材轧制困难原因分析

针对部分Q195冷轧板材存在轧制困难的现象，进行了现场检验与分析。带状组织、混晶现象严重导致变形强化系数偏高是造成轧制困难的主要原因。     

唐钢薄板坯连铸连轧生产中半无头轧制技术分析

介绍了热轧薄带钢生产中半无头轧制的优点，并对唐钢薄板坯连铸连轧生产中半无头轧制的工艺方案和关键技术进行了技术分析。     

轧机主传动电机励磁控制分析

在技术资料短缺的情况下，结合实际经验，绘制出进口轧机主传动电机励磁控制电路图，并进行了较为详细的分析。     

Mechanism of heat transport in nanofluids

We have calculated thermal conductivity of alumina nanofluids (with water and ethylene glycol as base fluids) using temperature as well as concentration-dependent viscosity, η. The temperature profile of η is obtained using Gaussian fit to the available experimental data. In the model, the interfacial resistance effects are incorporated through a phenomenological parameter α. The micro-convection of the alumina nanoparticle (diameter less than 100 nm) is included through Reynolds and Prandtl numbers. The model is further improved by explicitly incorporating the thermal conductivity of the nanolayer surrounding the nanoparticles. Using this improved model, thermal conductivity of copper nanofluid is calculated. These calculations capture the particle concentration-dependent thermal conductivity and predict the dependence of the thermal conductivity on the size of the nanoparticle. These studies are significant to understand the underlying processes of heat transport in nanofluids and are crucial to design superior coolants of next generation.     

论薄板坯连铸连轧产品质量优势

通过对薄板坯连铸连轧工艺的分析，深入研究了其产品的质量优势，同时还指出了在产品生产过程中需要重点注意解决的一些问题。     

基于CH365型接口和MCX314As型运动控制器的PCI总线运动控制卡设计

以CH365型PCI总线接口和MCX314As型运动控制器为核心硬件,自主研发了基于运动控制器的PCI总线运动控制卡,该控制卡能够实现4轴位置、速度和S曲线的加减速控制,具有直线、圆弧、位模式插补功能及自动原位搜寻功能,同时具有4路信号输入和8路通用输出.