Characterization of blasted austenitic stainless steel and its corrosion resistance

It is known that the corrosion resistance of stainless steel is deteriorated by blasting, but the reason for this deterioration is not clear. A blasted austenitic stainless steel plate (JIS-SUS304) has been characterized with comparison to the scraped and non-blasted specimens. The surface roughness of the blasted specimen is larger than that of materials finished with #180 paper. A martensite phase is formed in the surface layer of both blasted and scraped specimens. Compressive residual stress is generated in the blasted specimen and the maximum residual stress is formed at 50–100 μm from the surface. The corrosion potentials of the blasted specimen and subsequently solution treated specimen are lower than that of the non-blasted specimen. The passivation current densities of the blasted specimens are higher those of the non-blasted specimen. The blasted specimen and the subsequently solution treated specimen exhibit rust in 5% sodium chloride (NaCl) solution, while the non-blasted specimen and ground specimen do not rust in the solution. It is concluded that the deterioration of corrosion resistance of austenitic stainless steel through blasting is caused by the roughed morphology of the surface.     

Multidisciplinary optimization of gas-quenching process

Distortion as a result of the quenching process is predominantly due to the thermal gradient and phase transformations within the component. Compared with traditional liquid quenching, the thermal boundary conditions during gas quenching are relatively simple to control. By adjusting the gas-quenching furnace pressure, the flow speed, or the spray nozzle configuration, the heat-transfer coefficients can be designed in terms of both the component geometry and the quenching time. The purpose of this research is to apply the optimization methodology to design the gas-quenching process. The design objective is to minimize the distortion caused by quenching. Constraints on the average surface hardness, and its distribution and residual stress are imposed. The heat-transfer coefficients are used as design variables. DEFORM-HT is used to predict material response during quenching. The response surface method is used to obtain the analytical models of the objective function and constraints in terms of the design variables. Once the response surfaces of the objective and constraints are obtained, they are used to search for the optimum heat-transfer coefficients. This process is then used instead of the finite-element analysis. A one-gear blank case study is used to demonstrate the optimization scheme.     

回火过程应力场计算机模拟

回火过程应力场计算机模拟林家骝，杨振枢，于震宗，段贵明（清华大学）郭剑仁，史全兴，谢克仁（内蒙古第一机器厂）ＡＳｔｕｄｙｏｆＮｕｍｅｒｉｃａｌＳｉｍｕｌａｔｉｏｎｏｆＳｔｒｅｓｓＦｉｅｌｄｄｕｒｉｎｇＴｅｍｐｅｒｉｎｇ￥ＬｉｎＪｉａｌｉｕ；ＹａｎｇＺ...     

容器焊缝错边残余应力与载荷应力的测定研究

本文对焊接容器错边和不错边的焊接接头进行了电测法的残余应力测试，确定了焊接残余应力的大小及方向，并在加载的条件下，对各焊接接头测点进行了综合应力测试，并给出了受载条件下的应力分布。     

冷却器盘管失效分析及防范措施

本文介绍了冷却器盘管破裂泄漏的情况，分析了失效破坏的原因，并提出防止冷却器盘管破裂泄漏的措施。     

谈如何提高二次精制盐水质量

介绍了锦化化工(集团)有限责任公司提高二次精制盐水质量的成功经验,讨论了过滤系统中碳素烧结管间距、一次盐水的质量及其游离氯含量、人为操作失误和助体给料量等五大因素对二次精制盐水质量的影响,并采取了相应的措施,如调整合适的碳素烧结管间距、改走砂滤器、更换过滤器碳素管等。介绍了二次精制盐水精制系统树脂塔精制盐水的操作要素,诸如控制盐水流量最高为68m3/h、温度在(60±5)℃、pH值在9左右,控制树脂塔的压差、树脂填充量、树脂性能、仪表阀的检查情况等,从而生产出高质量的二次精制盐水,保证了离子膜电解槽的平稳、高效运行。     

《动态网站开发》课程教学改革探索

《动态网站开发》课程是中职学校计算机专业的核心课程,传统的授课方式以讲授理论为主,实际操作较少,这种方式很难适应现在中职学校的教学,必须打破传统的教学理念,对《动态网站开发》课程进行改革。     

浅谈中职计算机课程中如何创设问题情境

在教学中,创设问题情境是一种科学有效的教学手段。通过对一堂计算机基础课《PPT动画路径》的分析,探究如何在中职计算机课程中创设问题情境,提高课堂教学实效性,并对容易出现的问题进行简单的阐述。     

胶层厚度对拉伸试样应力分布影响的数值分析

运用弹塑性有限元法研究了胶层厚度对承受拉伸载荷的对接接头胶层内应力分布的影响．三维有限元法数值分析的结果表明，随胶层厚度减小，胶层中正应力SZ与剪应力SYZ的分布趋于均匀；而对正应力SY而言，胶层厚度为0．15mm时，其边缘峰值应力最低。     

Shear-rate dependence of first normal stress difference of poly(isoprene-b-styrene) in solution near the order-disorder transition temperature

Viscoelastic properties of poly(isoprene-b-styrene) in dioctylphthalate under steady shear flow were measured near the order—disorder transition temperature. In ordered states, first normal stress difference N₁ is proportional to shear rate at low region, but becomes proportional to at the high region, similar to the N₁ behaviour of polymer blends undergoing shear-induced homogenization. Because the existence of microdomains was confirmed at the high region by the flow birefringence method, it is concluded that the above N₁ behaviour is not caused by shear-induced homogenization, but is probably caused by the shear-induced alignment of the microdomain structure.