Polymerization behavior and polymer properties of eosin-mediated surface modification reactions

Surface modification by surface-mediated polymerization necessitates control of the grafted polymer film thicknesses to achieve the desired property changes. Here, a microarray format is used to assess a range of reaction conditions and formulations rapidly in regards to the film thicknesses achieved and the polymerization behavior. Monomer formulations initiated by eosin conjugates with varying concentrations of poly(ethylene glycol) diacrylate (PEGDA), N-methyldiethanolamine (MDEA), and 1-vinyl-2-pyrrolidone (VP) were evaluated. Acrylamide with MDEA or ascorbic acid as a coinitiator was also investigated. The best formulation was found to be 40 wt% acrylamide with MDEA which yielded four to eightfold thicker films (maximum polymer thickness increased from 180 nm to 1420 nm) and generated visible films from fivefold lower eosin surface densities (2.8 versus 14 eosins/μm²) compared to a corresponding PEGDA formulation. Using a microarray format to assess multiple initiator surface densities enabled facile identification of a monomer formulation that yields the desired polymer properties and polymerization behavior across the requisite range of initiator surface densities.     

Synthesis and properties of PDMS modified waterborne polyurethane–acrylic hybrid emulsion by solvent-free method

A new type of polysiloxane modified polyurethane–acrylic hybrid emulsion was synthesized by solvent-free method and the polysiloxane was introduced into the soft segment of polyurethane chains using dihydroxybutyl-terminated polydimethylsiloxane (PDMS). The formed film from the hybrid emulsion could provide obviously higher water-resistance property. The preparation technologies such as the content of carboxy group and acrylic monomer, the rate and the time of emulsification were discussed systematically. The chain structure and the particle size were confirmed by the analysis of Fourier transform infrared spectroscopy and transmission electron microscopy, respectively. The effect of PDMS content on the water resistance and the mechanical property were investigated by absorbed water ratio, water contact angle and dynamic mechanical measurement.     

CpTi(dbm)Cl_2催化烯烃聚合及其聚合物性质

开发了一种新型非茂聚烯烃催化剂———CpTi(dbm)Cl2,考察了催化剂在均相及负载条件下对乙烯及乙烯-1-己烯共聚的催化行为。催化剂在均相条件下对乙烯聚合的催化活性较低,但用MgCl2和MgCl2/SiO2复合双载体对催化剂进行负载后,催化乙烯聚合具有非常好的催化活性。催化剂还具有良好的共聚能力及良好的氢调敏感性。     

原油破乳脱钙复合剂的研制

介绍了原油破乳脱钙复合剂的筛选方法。所用的破乳剂有PY、UD 10、2 0 40、SDX、SL、硬脂酸 三乙醇胺 ,所用的脱钙剂有KL 1、KL 2、KL 3、KL 4、YH、EA、SJ、LP。首先将一定量的破乳剂与原油混合 ,振荡、静置 ,按油水分层情况及脱水率 ,筛选出较优的破乳剂。然后 ,在已加入破乳剂的原油中加入一定量的脱钙剂水溶液 ,振荡、静置 ,用燃烧瓶法处理油样 ,用原子吸收分光光度计测其钙含量 ,并与未经处理的原油对比。根据脱钙率 ,筛选出较优的脱钙剂。经过对破乳剂和脱钙剂的种类、用量、pH值等条件的选择 ,配出了针对俄罗斯原油、布伦特原油、扎非罗原油破乳、脱钙效果最好的复合剂PY YH、PY EA ,其脱钙率大于 80 %,脱水率大于98%,可直接用于炼厂的原油破乳脱钙工艺中。     

乳化炸药的乳化物理模型和理想乳化模态

文章以平推流模拟了乳化炸药乳胶质的形成过程,并建立了机械强制乳化的物理模型及理想模态。     

新型聚丙烯酸(934P、980)树脂的制备

详细研究了以乙酸乙酯和环己烷为溶剂，丙烯酸为单体，BPO，LPO，AIBN为引发剂，聚烯基多醚为交联剂，合成增稠能力强、透明度高的聚丙烯酸树脂。于混和溶剂存在下制得的聚合物，消除了以往由二氯甲烷为溶剂的反应介质中所得产品的毒性，可广泛应用于医药及日用化工等行业。     

光面爆破专用炸药的研究

文章分析了光爆炸药的性能特点，提出了制造光爆炸药新方法。该炸药密度（０．３５、０．７０ｇ／ｃｍ￣３）与爆速（１３００、２２００ｍ／ｓ）可调，贮存性能稳定；爆轰感度好，能满足不同硬度岩石尤其是软岩的光爆需要。     

Influence of Two Salicylate Components on the Particle Size of an Oil-in-Water Emulsion with Nonionic Surfactants

This paper reports a study undertaken using techniques of static and dynamic light scattering to investigate the influence of sodium salicylate and methyl salicylate on droplet size of oil-in-water emulsions. The rates of changes were measured by determining the size and distribution of the oil droplet in the material. All emulsions showed a bimodal size distribution; the mean diameters and polydispersity were calculated from intensity. These data were analyzed with nonlinear regressions and bootstrap methodology. An amount of methyl salicylate component induced a decrease of mean diameter and standard deviation. On the contrary, sodium salicylate entailed the growth of all droplet populations and coalescence for the highest concentration.     

水溶性聚偶氮酯的研究

用Ｐｉｎｎｅｒ合成方法制备了用ＰＥＧ４００封端的水溶性聚偶氮酯，并表征了其结构；研究了热分解反应动力学及用于乳液聚合的动力学。结果表明，该种引发剂具有引发速度快、热分解机理简单和具有辅助乳化作用等优点。     

Modelling of addition polymerization processes — Free radical,ionic, group transfer,and ziegler–natta kinetics

A brief review of addition polymerization processes is presented with a summary of the key characteristics classified by kinetic mechanism (free-radical, anionic, cationic, group transfer, or Ziegler–Natta), phase behavior, and reactor type. A practical approach to modelling in the industrial R & D environment is discussed in terms of a CAD package for polymerization processes.