Surface morphology and nodule formation mechanism of cellulose acetate membranes by atomic force microscopy

By the use of atomic force microscopy (AFM), formation mechanism of nodular structure in cellulose acetate membranes was systematically investigated. Elementary factors affecting the nodule formation were delineated on the basis of both kinetic and thermodynamic considerations. It was shown that (1) the exact nature of nodular structure is thermodynamic equilibrium glassy state; nodular structure will vanish in the rubbery state; (2) the thermodynamic factor affecting nodule formation is the membrane formation temperature; with the membrane formation temperature decreasing, more chain segments are able to form nodular structures; (3) nodule formation is dependent on the segment rearrangement; variation of the solvent environment is the major kinetic factor affecting the segment rearrangement and nodule formation. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 1328–1335, 2003     

Microporous anisotropic phase inversion membranes from bisphenol A polycarbonate: Effect of additives to the polymer solution

Phase inversion is a very flexible technique to obtain membranes with a large sort of morphologies. Membrane properties can vary greatly depending on the kind of polymer system used. Bisphenol A polycarbonate (PC) could be used as a phase inversion membrane base polymer, and presents very good properties. Nevertheless, very little information on membrane preparation using PC and the phase inversion process can be found in the literature. In this work flat‐sheet microporous membranes were obtained by the phase inversion process using the immersion precipitation technique. A new polymer system was studied, consisting of polycarbonate, N‐methyl‐2‐pyrrolidone as solvent, water as the nonsolvent, and an additive. The influence of some parameters on membrane morphology, such as polymer solution composition, exposition time before immersion into the precipitation bath, and the kind of additive was investigated. Precipitation was followed using light transmission experiments and membrane morphology was observed through Scanning Electron Microscopy (SEM). The viscosity and cloud points of all polymer solutions were also determined. The results were related to the studied synthesis parameters, using the basic principles of membrane formation by the phase inversion technique, looking forward to establishing criteria to control the morphology of flat‐sheet membranes using polycarbonate as the base polymer. The results showed that both additives were able to increase pore interconnectivity and even suppress macrovoid formation. The decrease in the miscibility region of the polymer system and increase in mass transfer resistance are found to be the determining factors during polymer solution precipitation. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 3085–3096, 2002     

电泳沉积法γ-Al2O3微孔膜的制备与表征

采用电泳沉积法制备γ－Al2O3微孔膜，考察了干燥及烧成制度对膜形成的影响，并用IR，XRD，SEM，N2吸附－脱附等测试手段对γ－Al2O3微孔膜进行了表征。结果表明：采用电泳沉积法可成功地制备均匀的γ－Al2O3保护膜；实验中采用室温慢速干燥法，制得了完整的凝胶膜，经过焙烧可获得与基片结合良好的γ－Al2O3多孔膜，在焙烧过程中，γ－AlOOH发生如下的晶型转变：γ－AlOOH→345℃γ－Al2O3，并且随着焙烧温度的升高，γ－Al2O3膜的结晶性得到改善。此外，γ－Al2O3膜的断面结构较疏松，膜厚度大面均匀：一次成膜厚度达十几μm，γ－Al2O3微孔膜的孔径尺寸为纳米级。     

Membrane degumming of crude rice bran oil: Pilot plant study

The procedure for the classical chemical refining of vegetable oils consists of degumming, alkali neutralization, bleaching, and deodorization. Conventional refining of rice bran oil using alkali gives oil of acceptable quality, but the refining losses are very high. A critical work has been carried out to study the application of membrane technology in the pretreatment of crude rice bran oil. Oils intended for physical refining should have a low phosphorus content, and this is not readily achievable by the conventional acid/water degumming process. The application of membrane technology for the pretreatment of rice bran oil has been investigated. The process has already been successfully applied to other vegetable oils. Ceramic membranes, which are important from the commercial point of view, were examined for this purpose. The results showed that the membrane‐filtered oils met the requirements of physical refining, with a substantial reduction in color. It was observed that most of the waxy material was also rejected. Experiments were carried out to establish the relationship between permeate flux and rejection with membrane pore size, trans‐membrane pressure and micellar solute concentration.     

A New Method for Identifying Osmotically Limited and Gel Layer Controlled Pressure Independent Flux in Ultrafiltration

An unequivocal determination of whether pressure independent flux regime is osmotically controlled or gel layer dominated, is still open for discussion in the membrane literature. The present work reports a method that could be used to address this issue. It is shown that analysis of post steady state transient filtration data leads to clear demarcation of osmotically limited and gel layer controlled filtration. The method proposed in this work can also be used to estimate the additional filtration resistance offered by the polarization layer to the permeate flow in macromolecular ultrafiltration and has been verified experimentally. It has also been shown that the polarization layer thickness is not sensitive to the feed pressure but varies as a function of the bulk solute concentration; higher the bulk concentration, thicker is the polarization layer.     

Effect of thermal hysteresis on the gas permeation properties of 6FDA‐based polyimides

The effect of thermal hysteresis on the polymer chain packing and permeation properties of two 6FDA‐based polyimide isomers was investigated. Thermal quenching resulted in a small increase in the fractional free volume of the polyimides with respect to the samples that had been annealed. Quenching from above the glass‐transition temperature also resulted in larger increases in the permeabilities for both 6FDA–6FmDA and 6FDA–6FpDA with respect to annealed samples. Meta‐connected 6FDA–6FmDA exhibited a larger increase in the permeability after quenching than the para‐connected isomer, 6FDA–6FpDA. This larger increase in the permeability for 6FDA–6FmDA may have been due to differences in the effects of the increases in the free volume on the intersegmental resistance to chain motions. Although physical aging over a 3‐month period resulted in a reduction in the permeability of quenched samples of 6FDA–6FpDA, the quenched samples maintained higher permeabilities than the annealed samples. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 1174–1182, 2004     

细胞固定化催化生产精细化学品的研究进展Q

摘要：细胞固定化技术具有流程简单、生物相容、操作稳定等优点，可有效保证细胞活性，实现高效的细胞催化生产精细化学品。本文介绍了表面附着、凝胶包埋、聚电解质层层自组装膜等多细胞固定化方法，及其在二元醇、生物乙醇、乳酸、酯、多糖等精细化学品生产中的研究现状和进展，并分析讨论了各种方法存在的问题。同时，总结了近年来新发展的单细胞纳米涂层固定化方法的机理、趋势及应用于精细化学品生产的可能性。最后对细胞固定化催化生产精细化学品面临的技术挑战及研究方向做出展望，以期为精细化学品生产提供一定的技术支持。     

Cellulose membranes for reverse osmosis Part I. RO cellulose acetate membranes including a composite with polypropylene

With the aim of obtaining RO membranes for brackish water desalination from purified celluloses (cotton linters and bleached bagasse pulp), two reactions (heterogeneous and homogeneous) were applied for the synthesis of cellulose acetate (CA). The efficiency of the membranes was measured and compared with those prepared from purchased CA and prepared CA by acetylation of imported high-grade viscose wood pulp. The effect of blending CA with polypropylene (PP), on the efficiency of the prepared RO membranes was also studied. Results showed that the method of preparation of CA plays a profound effect on the salt rejection and water flux of the RO membranes. The efficiencies of RO membranes formed from heterogeneously acetylated celluloses are higher than those prepared from homogeneous ones. Blending the acetylated cellulose with 9% PP wastes improves the efficiency of membranes prepared from the homogeneously acetylated celluloses.     

Water flux,DSC, and cytotoxicity characterization of membranes of cellulose acetate produced from sugar cane bagasse,using PEG 600

Summary In this article, cellulose acetate produced through the homogeneous acetylation of sugar cane bagasse cellulose was used to produce membranes, using poly(ethyleneglycol) 600 (PEG 600) as an admixture. The membranes were characterized using water flux measurements (Payne’s cup), differential scanning calorimetry (DSC) and neutral red uptake (cytotoxicity). The results showed that PEG 600 acts as a crystallinity inductor and/or pore former in the cellulose acetate matrix. The induction of crystallinity is important for this system since it had not been reported on the literature yet. The results also demonstrated that the studied membranes present a nontoxic behavior.     

Studies on membrane formation mechanism by the light transmission technique. I

New parameters, light transmission rate and minimum light transmissions, are proposed. These two parameters reflect the characteristics of the membrane‐forming system and the formation process of the membranes by phase inversion. The relationship between the light transmission and the porous structure of the membrane can be explained by the geometrical optics principles. Variation of the two parameters combining Reuvers's phase separation theory provided a convenient analytical method to predict effectively membrane morphologies. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 174–181, 2003