Cu基络合物催化甲醇液相氧化羰化反应

针对甲醇液相氧化羰基化法合成碳酸二甲酯(DMC)工艺,开发了新型Cu基络合催化剂(CuB rnLm)。对CuB rnLm催化剂的活性及其稳定性进行了研究。实验结果表明,采用该催化剂,甲醇转化率和DMC选择性较高;元素价态和物质结构分析表明,CuB rnLm催化剂循环使用5次后仍保持较好的稳定性。采用正交设计和中心响应曲面法设计实验,并使用S tatistica软件进行统计分析,寻求出反应的主要影响因素,并得到优化的工艺条件:反应温度100~110℃、反应压力3.0~3.5M Pa、反应时间4~6h、CuB rnLm催化剂质量浓度(以甲醇的体积计)0.15~0.20g/mL。在此工艺条件下,甲醇转化率可达23%以上,DMC的选择性为96%~98%。     

复合材料层合曲梁分层问题的解析解法

根据叠加原理将含有分层的复合材料层合曲梁在横向载荷作用下的受力状态分解为在面受力状态与出面受力状态,再将出面受力状态分解为无分层曲梁受横向载荷状态与含分层曲梁承受附加剪切载荷状态。将分层问题归结为在附加剪切载荷状态中,层合梁附加位移与附加应力的分析,并据此建立了一个简单的力学模型。最后得到了由分层引起的附加位移与应力的解析解答,并用能量释放率方法确定了应力强度因子。     

TEM Studies of High Temperature Corrosion Behaviour of TiAl Intermetallics with Surface Modifications

The oxidation/sulphidation behaviour of a Ti‐46.7Al‐1.9W‐0.5Si alloy with a TiAl₃ diffusion coating was studied in an environment of H₂/H₂S/H₂O at 850^oC. The kinetic results demonstrate that the TiAl₃ coating significantly increased the high temperature corrosion resistance of Ti‐46.7Al‐1.9W‐0.5Si. The SEM, EDX, XRD and TEM analysis reveals that the formation of an Al₂O₃ scale on the surface of the TiAl₃‐coated sample was responsible for the enhancement of the corroison resistance. The Ti‐46.7Al‐1.9W‐0.5Si alloy was also modified by Nb ion implantation. The Nb ion implanted and as received sampels were subjected to cyclic oxidation in an open air at 800^oC. The Nb ion implantation not only increased the oxidation resistance but also substantially improved the adhesion of scale to the substrate.     

Fatigue crack growth in SiC particulates reinforced Al matrix graded composite

The SiC/Al graded composite was fabricated by powder metallurgy processing and its fatigue crack growth behavior was studied. The volume percentage of SiC particulates was distributed from 5 to 30% layer by layer on the cross section. Since the aluminium was dissolved together, there was no evident interface between the two layers with different volume fraction of SiC particulates. Fatigue crack growth was in direction of from 5 to 30% SiC layers under sinusoidal wave-form. The retardation of fatigue crack growth was found when crack propagated from low volume fraction of SiC to high volume fraction of SiC. The crack deflection and branching between two layers were observed, which decreased crack growth rates. In view of crack tip driving force, the plasticity mismatch between the layers shielded crack tip driving force, i.e. decreased the effective J-integral at the tip of the crack as the plastic zone of the crack tip spread from the weaker material into the stronger material.     

浇筑式沥青混凝土心墙型式改进的建议

本文根据浇筑式沥青混凝土主、副心墙材料的性能，分折了沥青混凝土心墙施工或运行中破坏的原因，建议用编织一无纺复合布取代预制块，以避免主、副心墙材料变形性能相差悬残对心墙运行的不利影响，从而发挥浇筑式沥青混凝土心墙的优越性。     

WC/Cu复合材料制备及其高温性能

用机械合金化法结合冷变形，制备了WC／Cu复合材料，研究了冷变形后复合材料的组织特征和高温退火时韵性能变化。结果表明：烧结后的材料经冷变形，组织呈显著纤维状，WC颗粒弥散分布，密度明显提高，达到理论密度的99．2％；复合材料经600～900℃高温退火，强度和硬度略有下降，塑性则有大幅提高；900℃退火时未发生明显的再结晶，界面结合良好；所制备的WC／Cu复合材料有优良的综合性能。     

T-ZnO晶须增强环氧树脂复合材料的力学行为

研究了以四脚状氧化锌（T-ZnO）晶须为增强剂，环氧树脂复合材料的力学行为。结果表明，由具有三维空间结构的T-ZnO晶须为增强剂所制备的环氧树脂复合材料具有各向同性的力学性能，T-ZnO晶须填加质量分数为6%时，就可使材料的力学性能改善；拉伸强度提高到169%，拉伸功几乎提高了100%，冲击强度提高到300%，抗弯的断裂功提高到158%，而压缩强度略有下降。     

纳米ZrO2等离子涂层的结构,性能和工艺特点

采用大气等离子喷涂技术(APS)，制备了常规氧化锆和纳米结构氧化锆两种涂层．利用扫描电镜(SEM)对涂层的显微结构进行了观察．对两种涂层的沉积效率、表面粗糙度和显微硬度作了对比研究．结果表明，粉末原料的显微结构、粒度、形态、喷涂工艺参数(喷涂功率和距离)对涂层的显微结构有较大的影响．等离子喷涂造粒纳米氧化锆粉制备的涂层沉积效率高而稳定，其显微结构与喷涂功率和距离密切相关．与常规氧化锆涂层相比，纳米结构氧化锆涂层具有较高的显微硬度和较低的表面粗糙度．     

复合材料空心飞轮多环套装整体变形及应力简化精细分析

采用多环过盈装配是解决复合材料飞轮径向强度过低的有效途径之一。本文作者采用平面应力简化模型,提出了计及过盈配合后变形导致实际过盈量增大计算飞轮套装后的初终应力分布的方法;提出了基于叠加原理计算多环过盈装配旋转飞轮应力的方法;提出了保证飞轮旋转时配合界面不脱离的相关临界转速的概念和计算方法。算例分析表明:过盈配合后的变形对初终应力的影响不能忽略;过盈量和套装环数与飞轮的初终应力和相关临界转速有密切的关系。     

Computational analysis of thin coating layer failure using a cohesive model and gradient plasticity

Thermal barrier coatings (TBC) are widely used to prevent transient high temperature attack and allow components high durability. Due to strong inhomogeneous material properties the TBC failure often initiates near the interface between the brittle oxide layer and the ductile substrate. A reliable prediction of the TBC failure requires detailed information about the crack tip field and the consequent fracture criteria. In the present paper both cohesive model and gradient plasticity are used to simulate the failure process and to study interdependence of the interface stress distribution with the specific fracture energies. Computations confirm that combination of the two models is able to simulate different failure mechanisms in the TBC system. The computational model has the potential to give a realistic prediction of the crack propagation process.