基于高速摄像的ESPI全场动态特性测量

采用高速摄像与ESPI技术相结合,将运动中的被测物位移随时间变化的状态以序列图像的形式实时记录,并运用图像处理技术,成功地实现了ESPI动态测量。测量了悬臂梁的自由振动过程,获得了悬臂梁的振动周期、振动频率和阻尼系数等动态特性,实验结果与理论计算值相吻合。     

NETWORK6000在脱离子水处理过程中的应用

脱离子水处理单元是一种顺序控制单元，对时序控制有严格的要求。文中介绍了一种新型的控制系统NETWORK6000在PTA装置脱离子水单元中的应用状况，为中小规模的装置应用提供了一种较典型的思路和借鉴，最后对系统的应用状况进行了评价。     

用介孔材料制备定向碳纳米管的研究进展

综述了近年来采用介孔材料制备定向碳纳米管的研究进展,包括介孔材料的合成及介孔材料在制备定向碳纳米管方面的应用。重点介绍了采用合成介孔材料的模板剂石墨化及介孔材料作为载体制备定向碳纳米管的方法,探讨了模板剂种类、催化剂的制备方法及反应温度和时间对定向碳纳米管生长的影响和定向碳纳米管生长的介孔限制机理,并提出了这一领域的研究方向。     

Preparation of aligned polyetherimide fiber by electrospinning

Fifteen to 20 wt % polyetherimide (PEI) solutions with 1-methyl-2-pyrrolidinone (NMP) were prepared. The electrical conductivity and surface tension of the solutions were determined. The fiber spinning technique of electrospinning was optimized in order to prepare unidirectionally aligned, structurally oriented nanofiber tows. The morphology of the PEI fibers was investigated using field emission scanning electron microscopy (FESEM). The well-aligned fibers with diameters between 0.58 and 0.90 μm (FESEM) were collected by electrospinning 20 wt % PEI solutions with NMP in the range of 8–10 kV onto a target rotating with a surface velocity 9.8 m/s. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

凸轮逆序测量方法

目前各杂志所发表的关于凸轮测量的文章，所讨论的均是凸轮的顺序测量方法，有关凸轮的逆序测量(反求工程)方法，尚未见于文字。本文将对凸轮的逆序测量方法进行探讨。     

陆相断陷湖盆中层序边界的形成机理及其识别特征研究

陆相断陷湖盆中层序边界是由于沉积物表面高出沉积基准面或盆地基准面、沉积物发生剥蚀或无沉积作用所形成的，其产生机理主要有边界断层停止活动、断块翘倾活动、湖盆整体抬升和湖平面下降。层序边界在地震特征上、测井曲线上、钻井剖面中的岩性、岩相特征、古生物组合、微量元素的变化上均有明显的特征。利用这些特征，在济阳坳陷下第三系中识别出9个三级层序。     

垂直定向液晶光阀及光电特性的研究

系统地讨论了排列相畸变模式液晶光阀结构，原理和制作，结合实际测试对其等效电路和电学匹配进行了分析，详细讨论了它的光电特性及相互关系，实测的液晶垂直排列方式工作的液晶光阀性能指标为，分辨率大于５０ｌｐ／ｍｍ，白光输入灵敏度为６．７７μＷ／ｃｍ＾２，响应时间为２００ｍｓ／３００ｍｓ，白光输出对比度为２００：１。     

Chrestenson函数序列的生成方法及其数学分析

本文提出了适于三种序号的Ｃｈｒｅｓｔｅｎｓｏｎ函数序列的复制方法，对其复制过程进行了数学分析，并指出当Ｃｈｒｅｓｔｅｎｓｏｎ函数退化为Ｗａｌｓｈ函数时，此方法即为复制理论中的平移复制方法。     

A Standard Model-Theoretic Approach to Operational Semantics of Recursive Programs

In this paper we try to introduce a new approach to operational semantics of recursive programsby using ideas in the“priority method”which is a fundamental tool in Recursion Theory.In lieu ofmodelling partial functions by introducing undefined values in a traditional approach,we shall define apriority derivation tree for every term,and by respecting the rule“attacking the subterm of thehighest priority first”we define transition relations,computation sequences etc.directly based on astandard interpretation which includes no undefined value in its domain.Finally,we prove that ournew approach generates the same operational semantics as the traditional one.It is also pointed outthat we can use our strategy to refute a claim of Loeckx and Sieber that the opperational semanticsof recursive programs cannot be built based on predicate logic.     

The effect of fibre alignment on composite strength: II. The strength of angle-ply laminates

Experiments have been carried out on relatively wide angle-ply laminate samples with very short gauge lengths. These proved to be very much stronger than samples tested in earlier work, and which form the basis for our present design with these materials. It is highly likely that the early results for strength were more indicative of edge effects than true laminate strength. This is confirmed by data from tests on pressurized tubes. A review of the literature on this shows that such tests produced results which can be an order of magnitude higher than the early laminate tests. Thus our design calculations could well be severely underestimating the potential strength of angle-ply laminates. This may be having serious consequences for the aerospace industry, through the use of design criteria for strength which may be too conservative. Single-fibre experiments may pave the way for more realistic estimates of angle-ply laminate strengths. These indicate that a simple one-third power rule can be used to estimate the potential strength. However, this is purely ad hoc at present, and needs to be put on a firmer footing through both theoretical and experimental studies. Furthermore, if this approach is adopted, edge effects will still have to be allowed for, and estimated on the basis of the aspect ratio of the part.