Wear resistance of plasma coatings for a constant work of friction

We analyze the wear resistance of plasma coatings for a constant work of friction. The dependences of the wear resistance of the coatings are obtained for a broad range of loading conditions. It is shown that the minimum sensitivity to loading conditions is exhibited by the molybdenum coatings. It is also established that the wear resistance of the coatings decreases as the amplitude of displacements increases and the cyclic frequency of the tests decreases due to the intensification of fatigue processes on the surfaces. The comparative characteristics of coatings are presented. __________ Translated from Problemy Prochnosti, No. 5, pp. 94–100, September–October, 2007.     

Drying Characteristics of Barley Grain Dried in a Spouted-Bed and Combined IR-Convection Dryers

A study was performed to determine the drying characteristics and quality of barley grain dried in a laboratory scale spouted-bed dryer at 30, 35, 40, and 45°C and an inlet air velocity of 23 m/s^-1, and in an IR-convection dryer under an infrared radiation intensity of 0.048, 0.061, 0.073, and 0.107 W cm^-2 at an air velocity of 0.5 m/s^-1. The results show that the first, relatively short, phase of a sharp decrease in the drying rate was followed by the phase of a slow decrease. The time of barley drying depended on temperature of inlet air in a spouted-bed dryer and on radiation intensities in an IR-convection dryer. Barley drying at 45°C in a spouted-bed dryer was accompanied by the lowest total energy consumption. The average specific energy consumption was lower and the average efficiency of drying was higher for drying in a spouted-bed dryer. The effective diffusivities were in the range 2.20-4.52 × 10^-11 m² s^-1 and 3.04-4.79 × 10^-11 m²/s^-1 for barley dried in a spouted-bed and in an IR-convection dryer, respectively. There were no significant differences in kernel germination energy and capacity between the two drying methods tested.     

A unified proposal for characteristic testing methods and figure of merit of 8‐kV/3.5‐kVA class light‐triggered thyristors

Power devices with high capability have been developed. 8‐kV/3.5‐kA‐class light‐triggered thyristors have the highest capability among power devices. These devices are used in the Kii Channel HVDC transmission system in Japan. In this paper, we report the extracted problems of conventional testing methods of 8‐kV/3.5‐kA‐class light‐triggered thyristors among manufacturers, and the proposed unified testing methods on the basis of element characteristics and operating conditions in the Kii Channel HVDC system. Furthermore, we propose a figure of merit for power devices for the practical use, and try to extract elements used at the Kii Channel HVDC system with small margins and low withstand capabilities. © 2002 Wiley Periodicals, Inc. Electr Eng Jpn, 140(3): 61–70, 2002; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.10024     

Upgrading coal-derived liquids to diesel fuel

Distilled fractions of a coal-derived liquid from the H-Coal process were upgraded to diesel fuel by catalytic hydrotreatment. The total hydrotreated products were distilled into naphtha (<180°C) and diesel fuel fractions (>180°C) and the diesel fractions were analysed for hydrocarbon-type composition, hydrogen content and some diesel fuel properties. GC—MS-analyses were carried out on the hydrocarbon-type fractions to identify individual chemical compounds. To investigate the effect of different distillation cut points on diesel fuel yield and properties, cut points for one hydrotreated product were varied. The diesel fuel cetane numbers were correlated with percentage hydrogen, total aromatics and saturates. Cetane numbers above 40 were obtained for diesel fuels containing (i) more than 75% saturates, (ii) less than 15% total aromatics and (iii) a hydrogen content above 12.8%. Compounds identified by GC—MS-analyses (in the diesel fractions) were typical aromatic and cycloparaffin compounds. Normal-and iso-paraffin compounds were not detected. By varying the distillation cut point from 135 to 180°C, the cetane number of the residual diesel fraction improved from 37 to 44. This increase is ascribed to the removal of aromatic compounds in the 135–180°C boiling point range.     

HHD型核子秤电离室物理性能检测

HHD型核子秤电离室已成功地使用于HCS型核子秤.对它的各种物理性能指标进行了检测,各项性能指标都达到了设计要求。     

Thermophysical properties data: Government-university-industry cooperation in multidisciplinary research

Historical developments regarding the realization of the importance of reliable thermophysical properties data in engineering applications are presented. The events leading to the establishment of the Symposium on Thermophysical Properties in 1959 and the accomplishments of the symposia series since then are discussed. Contributions of the National Bureau of Standards to the thermophysical properties field are described.Welcoming address presented at the Ninth Symposium on Thermophysical Properties, June 24–27, 1985, Boulder, Colorado, U.S.A.     

Studies on chitin 3—effect of coagulants and annealing on the preparation and the properties of chitin membrane

Chitin membrane was prepared by casting a N,N-dimethyl acetamide, N-methyl 2-pyrrolidone and lithium chloride (DMA-NMP-LiCl)solution of chitin and coagulating with several media. The effect of the coagulants on membrane formation was studied. 2-Propanol was found to be more favourable than methanol, ethanol, acetone and mixtures of 2-propanol and water. The membrane obtained in 2-propanol was subjected to annealing. Annealing made the membrane dense and strong. The tensile strength of the membrane annealed at 145°C for 2hr was about twice that of an unannealed membrane. The solute permeability of the annealed membranes was lower than that of the original one. These phenomena could be clearly interpreted in terms of crystallinity.     

我国建筑涂料技术进步简评

从以下诸方面简述我国建筑涂料的技术进步:⑴新品种涂料的研制开发;⑵加强对配套材料及施工技术的研究;⑶超细填料在涂料中的应用;⑷计算机自动配色技术;⑸产品标准的修订;⑹建筑涂料的实用范围扩大。     

凸轮进给式双管平头倒棱机

研制的凸轮进给式双管平头倒棱机可自动完成上料→夹紧→平头倒棱→松开→退料动作循环，同步准确，可靠性高，平头倒棱质量好。介绍了该装置的工作原理、工作程序、技术性能、设备组成以及刀具和夹具的特点。     

康山金矿地质地球化学特征及其成因

康山金矿产在豫西熊耳山古隆起区的结晶基底太华群和盖层中元古界熊耳群地层接触界面附近，矿体严格受构造破碎蚀变带控制。流体包裹体，稳定同位素等研究表明，成矿物质来自太华群变质岩，成矿流体的性质与变质热液截然不同，而与花岗岩浆热液相近似。该矿床的形成与燕山期发生的同构造－花岗岩浆期热液活动有关，金沉淀成矿阶段有大气水的混入。