角接接头焊缝外观检查质量标准的探讨

针对厚壁管角接接头多次出现裂缝,解剖后又没有发现足以引起裂缝的除未焊透外的其它焊接缺陷的情况,认为除应力集中外,角接接头本身的强度也是决定是否会开裂的一个重要原因,为此建立了一个数学模型,同时结合实例证明.按目前大多数人认可的角接接头焊脚的定义,根据DL/T869-2004<火力发电厂焊接技术规程>去控制焊接尺寸,会出现焊缝有效厚度不足的问题.从而根据角接接头有效厚度不应小于最小壁厚的观点,提出对此类角接接头焊缝外观质量控制的几点意见.     

不等厚板过渡削薄对接焊缝的超声波探伤

不等厚板经过渡削薄处理后的对接焊缝,由于厚度的不均匀,射线穿透时的衰减不一样,对射线检测带来很大的麻烦。常用的超声波探伤方法在定位和定级方面比较困难,本文给出利用现在先进的数字式超声波探伤仪进行准确探伤的方法。     

Experimental Investigation of Epoxy Bonded Polymethylmethacrylate Joints

This paper presents an experimental investigation into various aspects of epoxy-bonded polymethylmethacrylate (PMMA) and PMMA-to-aluminium joints. The effects of adhesive thickness, overlap area, surface roughness, and environmental exposure on the joint strength were studied. Results indicated that the joint strength was not directly proportional to the overlap area, while sanding had a positive effect on the joint strength. A negative effect was observed when adhesive thickness was increased. The fatigue behaviour of adhesively-bonded joints under dynamic loading was found to be independent of frequency, for the range of values tested; however, it was dependent on the test temperature with greater reduction in fatigue life observed in PMMA-to-aluminium joints at higher temperature. Empirical equations from which the fatigue life of joints can be predicted were obtained by regression analysis. Intermittent fatigue testing of the joints was also performed. The epoxy adhesive tested proved to be a satisfactory choice for outdoor exposure. The rate of degradation of the adhesive was slow with the adherend itself degrading at a faster rate than the adhesive or the bondline.     

多层水平气流带式干燥机的数学模型

根据干燥传质传热学原理和干燥动力学特性，建立了水平气流带式干燥机干燥过程的数学模型。该模型可以预测干燥机合理的通风道高度、带翻转最佳时间和热风风速等。为优化多层带式干燥机的结构或设计新的水平气流带式干燥机提供了理论依据。     

Analysis of the diffusion layer thickness, equivalent circuit and conductance behaviour for reversible electron transfer processes in linear sweep voltammetry

The parametric dependence of the diffusion layer thickness upon electrode potential and scan rate has been derived for reversible electron transfer processes in linear sweep voltammetry (LSV) using a simple analytical expression for the dimensionless current function. The quantitative variation of the conductance with potential and scan rate has been illustrated and the equivalent circuit pertaining to LSV has been proposed. Several earlier results pertaining to potential step experiments, thin layer voltammetry, surface bound LSV, radial flow at micro-ring electrodes, etc. are shown to arise from the general expression for the current function obtained here, thus indicating an isomorphism among various potential perturbation techniques.     

两极控制图在注塑瓶盖壁厚控制中的应用

针对注塑瓶盖壁厚控制的特点,介绍了统计过程控制(SPC)中的均值-极差(x-R)控制图在塑料瓶盖壁厚控制中的局限性,将两极(L-s)控制图与均值-极差控制图进行了比较,阐述了两极控制图在塑料瓶盖壁厚控制中的优越性,论述了两极控制图的构造原理和控制限计算方法,提出了两极控制图在注塑瓶盖壁厚控制中的应用,并在对两极控制图分析的基础上,对注塑成型的过程能力进行分析和改善。     

Shear-induced interactions in blends of HMMPE containing a small amount of thermotropic copolyester HBA/HQ/SA

Shear-induced interactions between high molecular mass polyethylene (HMMPE) melt and a thermotropic liquid crystalline copolyester, HBA/HQ/SA (TLCP) were investigated using large amplitude oscillatory shear and capillary shear. Polarized optical microscopy (POM) observations show that the mono-domain nematic TLCP droplets embedded inside a HMMPE melt may be readily elongated using large amplitude oscillatory shear. The HMMPE melt adjacent to the elongated TLCP filament was observed to crystallize faster than that in the matrix away from the interface. TEM analysis on the 1 wt% TLCP/HMMPE blend quenched after capillary shear shows that there are strong interfacial interactions between the elongated TLCP filament and the HMMPE matrix. Long range PE lamellae orientational order up to 2 μm away from the TLCP filament surface were observed, with all the lamellae surface normal parallel to the TLCP fiber. Additionally, a strong interfacial compatibility between the TLCP filament and the HMMPE matrix with an interfacial thickness of ∼30 nm has also been observed. The enhanced interfacial compatibility is attributed to the -CH₂- group interactions due to chain alignment in both components at their interface. These results provide a fundamental insight to other TLCP containing thermoplastics where compatibilities may be present due to segmental interactions.     

K_2O－CaO－Al_2O_3－SiO_2系统自释釉瓷化学组成的研究

本文从酸度系数着手，证实了Ｋ２Ｏ－ＣａＯ－Ａｌ４Ｏ久－ＳｉＯ２系统中存在自释釉组成，限定了其组成范围，０．６７％＜Ｋ２Ｏ＜１．２８％，１０．６４％＜ＣａＯ＜１３．６２％，１１．５３％＜Ａｌ４Ｏ３＜１５．３２％，７２．７３％＜ＳｉＯ２＜７４．０４％，并讨论了自释釉瓷的性能。     

Effect of TiO2 thin film thickness and specific surface area by low-pressure metal–organic chemical vapor deposition on photocatalytic activities

TiO₂ photocatalyst films having an anatase crystal structure with different thickness were prepared by the low-pressure metal–organic chemical vapor deposition (LPMOCVD) to examine the effect of growth conditions on photocatalytic activity. Film thickness was linearly proportional to the deposition time. Structure of the film was strongly dependent on the deposition time. In early stage of deposition, fine particles deposit on the substrate. As increasing the deposition time, crystal orientation is gradually selected following the Kolmogorov model and c-axis oriented columnar crystals become dominant. The photocatalytic activity strongly depends on the film deposition time (or film thickness) in nonlinear way. The optimum thickness of TiO₂ catalyst film grown by LPMOCVD may locate between 3 and 5 μm.     

涂料原料和涂层厚度对反射隔热保温性能影响研究

通过研究涂料配方中所用乳液、颜料、常规填料和隔热填料在红外灯下的反射、隔热和保温性能，发现高折射率的二氧化钛和含有微孔的硅藻土具有最佳的反射和隔热保温效果，轻质碳酸钙和重质碳酸钙具有一定的隔热保温作用，而理论上具有隔热保温效果的填料海泡石等并没有预期的效果。涂层厚度对隔热保温效果具有一定影响，但是没有颜料和填料的影响大。隔热涂料使用的填料应含有硅藻土、二氧化钛以及一些常规的填料。