Effects of weak shear on hyperswollen lyotropic smectic liquid crystals

We have developed a Zimm-type viscometer specially designed for the simultaneous measurements of the structure factor and the viscosity of hyperswollen lyotropic liquid crystals under a very weak shear. We have investigated the shear effects on the layer undulation fluctuation in the lamellar structure and the transition from the anisotropic lamellar to the isotropic sponge phase. We have found a significant difference in the rheological properties between the lamellar and the sponge phase: The former exhibits non-Newtonian flow behavior, while the latter exhibits Newtonian behavior.Paper presented at the Twelfth Symposium on Thermophysical Properties, June 19–24, 1994, Boulder, Colorado, U.S.A.     

钢筋混凝土框架-剪力墙结构在强震作用下的非线性分析——Ⅱ、程序及算例

运用文献[1]所介绍的分析原理与方法,编制了强震作用下钢筋混凝土框架-剪力墙结构非线性地震反应时程分析的程序。本文介绍该程序的功能、框图,以及利用该程序计算所得到的几栋钢筋混凝土结构的非线性地震反应分析结果。算例表明,本程序计算结果可靠,能很好地用于解释震害和预测地震时结构可能发生的破坏。     

Temperature Dependence of the Raman Spectrum in Lithium Oxide Single Crystal

Temperature dependence of the Raman spectrum of lithium oxide single crystal has been measured over a temperature range of 80 to 1073 K. The frequency shift and the line width of the Raman spectrum in lithium oxide were about 531 and 4.5 cm^-1 at 80 K, respectively. At 1073 K, the frequency shift and the line width attained the values of 464 and 112 cm^-1, respectively. The strong temperature dependence of the frequency shift and line width was compared with data from some crystals with a fluorite structure.     

Pb/Sn凸剪切性能研究

在实际使用条件下,Pb/Sn凸点会由于承受温度循环而产生剪切应力,剪切应力导致的主要失效方式是开裂.通过对倒装焊后Pb/Sn凸点剪切强度的测量及对剪切后断口的分析,发现破坏主要发生在凸点下金属(UBM)层内部或UBM与Al焊盘之间,平均剪切强度受凸点尺寸影响很小,范围在21～24MPa。     

Optical scattering in beef steak to predict tenderness using hyperspectral imaging in the VIS-NIR region

The objective of this research is to develop a non-destructive method for predicting cooked beef tenderness using optical scattering of light on fresh beef muscle tissue. A hyperspectral imaging system (λ = 496–1,036 nm) that consists of a CCD camera and an imaging spectrograph, was used to acquire beef steak images. The hyperspectral image consisted of 120 bands with spectral intervals of 4.54 nm. Sixty-one fresh beef steaks, including 44 strip loin and 17 tenderloin cuts, were collected. After imaging, the steaks were cooked and Warner-Bratzler shear (WBS) force values were collected as tenderness references. The optical scattering profiles were derived from the hyperspectral images and fitted to the modified Lorentzian function. Parameters, such as the peak height, full scattering width at half maximum (FWHM), and the slope around the FWHM were determined at each wavelength. Stepwise regression was used to identify 7 key wavelengths and parameters. The parameters were then used to predict the WBS scores. The model was able to predict WBS scores with an R = 0.67. Optical scattering implemented with hyperspectral imaging shows limited success for predicting current status of tenderness in beef steak.     

Simulation of the Forming Behaviour of a Boron Modified P91 Ferritic Steel

The forming behaviour at high temperature of a modified 9%Cr‐1%Mo (P91) ferritic steel containing B and Ti for elevated temperature service was investigated. The microstructure of the as‐received material is mainly martensite at room temperature, but special etching revealed prior austenite grains of about 25 μm in size. Torsion tests were conducted at temperatures in the range 850 to 1250 °C to simulate the hot rolling process under comparable conditions of temperature, strain rate and strain. The deformation data obtained from these tests were correlated with the Garofalo equation with a stress exponent of 4.6 and an activation energy of 315 kJ/mol. This equation was used to predict the formability behaviour for the rolling process and also to determine the maximum forming efficiency and stability of the steel. A temperature of 1200 °C is recommended to conduct the forming process.     

手持式GPS测量在地球化学勘查中的应用

在大比例尺的化探测量中，用GPS单点绝对定点技术来进行测网的布设，减少了控制测量环节。降低了生产成本。因此，GPS绝对定点在化探测量中仍有应用的前景。但是，绝对定位时必须做到：(1)合理选择校正的控制点(三角点或四角点)；(2)正确校正参数；(3)定期地检测仪器；(4)保证仪器的高度角和有效工作时间。本次该方法应用在化探的测网布设中。实测面积7km^2，经传统测量仪器检查验收，证明文中提出的方案完全可以用于生产实践。     

Time and temperature effect on the linear–nonlinear viscoelastic transition threshold of a polymeric system

In the present study, the transition of a polymeric material from the linear to the nonlinear viscoelastic behavior and the determination of the nonlinearity stress threshold variation with time and temperature are investigated. For this purpose a systematic experimental program consisted of thermal and mechanical characterization of certain polymeric material followed by isothermal creep tests at different stress levels and temperatures was conducted. Through isochronal curves that occurred from creep tests, the nonlinearity threshold dependence on both time and temperature is presented. The reported results provide information that is critical for the design and development of polymer structures and components. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008