铁基气门导管材料性能的控制

介绍了在铁基气门导管的生产过程中,加强关键工序的质量管理,以确保产品材料性能的合格与稳定。     

ANALYSIS OF OPEN SUN DRYING EXPERIMENTS

Open sun drying has lost its previous importance due to the fact that different factors affect its reliability and the quality of the products obtained.

One of the set-backs for the analysis of solar drying exoeriments is their deoendence on a non-controlled source of energy, i.e. solar radiation depends on climatic conditions and experiments are difficult to compare. It is thus necessary to investigate the advantages of a particular set up as well as the climatic influences. Open sun drying could constitute the natural reference, allowing the comparison of different drying strategies.

A new way of standardizing drying times, based on solar radiation inout, is proposed, to allow better evaluation of the experiments. An equivalent time is defined, allowing comparison of experiments carried out under different circumstances. Carrots and potatoes were used in these experiments.

The use of the average daily solar radiation 15.28 MJ m^-2.d^-1 in Palma de Mallorca (39.33°N, 2.37°E), is proposed for comparison purposes. An improvement of more than 12 % in the explained variance was observed, the unexplained variance being lower than 1 %.     

24m~2烧结机自动化改造方案

介绍烧结机不停产自动化改造的方法,阐述构成工艺过程控制的DCS系统组合以及变频调速技术改造电磁滑差调速成功的选型方法。     

On the use of the WLF model in polymers and foods.

The validity of the WLF model with fixed "universal" coefficients was tested against that of the model original form with variable coefficients using published coefficients of polymers and amorphous sugars crystallization and viscosity data. The disagreement between the two versions of the model is particularly large at temperature ranges starting about 20 to 30 degrees K above the glass transition or reference temperature, excluding the former from being a model of general applicability. Because the WLF model mathematical structure entails the existence of an almost linear region near the reference temperature, establishment of its validity as a kinetic model and meaningful determination of its constants requires data spread over an extended temperature range, especially when the experimental results have a scatter.     

解析参数对活性焦再生过程及再生效果的影响

 活性焦的热解析参数对再生活性焦的脱硫脱硝性能和机械强度至关重要。为了明确解析参数对活性焦再生过程和再生效果的影响规律,通过热解析试验探究活性焦硫残余比例、CO₂和CO生成量及再生活性焦脱硫脱硝性能随解析温度和解析时间的变化规律,继而明确适宜的活性焦热解析参数。结果表明,活性焦升温解析过程中,脱硫产物在317 ℃左右迅速分解,随后分解速率下降;在进入恒温解析阶段后脱硫产物分解速率先快速下降,而后进入缓慢解析状态。硫残余比例随恒温解析温度的升高而下降,在530 ℃下解析3 h可使脱硫产物完全解析;解析温度高于430 ℃后,活性焦表面的酚基、醌基、内酯基等含氧官能团分解量明显增加,并随恒温解析温度的升高而持续增加,分解所生成的CO和CO₂也随之大幅增加,这将使活性焦的孔隙结构进一步发展,继而不利于活性焦机械强度的保持;解析温度低于530 ℃时,硫残余比例随解析温度的升高而持续降低,使再生活性焦的脱硫脱硝性能持续提高;解析温度高于530 ℃后,含氧官能团分解量随解析温度的升高而持续增加,这将有利于提高活性焦表面SO₂氧化反应速率,继而使再生活性焦的脱硫性能持续升高,但酚基、内酯基等酸性含氧官能团的分解使再生活性焦对NH₃的吸附性能降低,进而使其脱硝性能降低。在兼顾再生活性焦脱硫脱硝性能、机械强度和生产效率等多方面因素时,430 ℃恒温解析3 h是相对较优的解析参数。在此解析条件下,再生活性焦的硫残余比例仅为1.8%,含氧官能团尚未发生大量分解,脱硫脱硝性能相对较为优良。     

Hydrosilylation and dehydrocondensation reactions of methylhydridesiloxane to acrylic and methacrylic acids

The hydrosilylation of α,ω‐bis(trimethylsiloxy) methylhydridesiloxane (degree of polymerization ≈ 53) with acrylic and methacrylic acid with various ratios of the initial compounds, in the presence of platinum hydrochloric acid, has been investigated. In the presence of platinum hydrochloric acid, competitive dehydrocondensation reactions take place with the formation of various oligomers with various chemical links. In the later stages of the reaction, three‐dimensional systems have been obtained. During dehydrocondensation, the reaction order, reaction rate constants, and activation energy have been determined. The structures of the synthesized oligomers have been determined with IR and NMR spectroscopy data. Gel permeation chromatography, differential scanning calorimetry, and X‐ray analyses of the synthesized oligomers have been carried out. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 3243–3252, 2007     

六铝酸钙材料的合成及其显微结构研究

分别采用轻质碳酸钙和活性氧化铝 ,或纯铝酸钙水泥和活性氧化铝为初始原料 ,反应烧结合成了六铝酸钙 (CA6)材料 ,研究了原料和成型压力对合成材料的烧结性能和显微结构的影响 ,同时借助于XRD、TG -DSC、SEM和EDAX等测试手段对其反应过程、物相变化和显微结构进行了分析和观察。研究结果表明 :(1) 130 0℃时 ,合成材料的主晶相为刚玉相和CA2 ,并开始有CA6形成 ;温度升至14 0 0℃ ,CA6大量生成 ;15 0 0℃时反应完成 ,产物全部为CA6相。 130 0～ 15 0 0℃时 ,上述反应表现为体积膨胀过程 ,试样的体积密度和径向线收缩率随温度的变化不大 ;而高于 15 0 0℃时 ,试样明显趋向烧结 ,体积密度升高 ,线收缩率加大。采用纯铝酸钙水泥和活性氧化铝合成的试样的体积密度均高于采用轻质CaCO3 和活性氧化铝的 ,尤其在烧成温度高于 15 0 0℃时。坯体的成型压力对这两种合成试样的烧结性能均没有显著影响。 (2 )合成六铝酸钙材料的晶粒形貌与合成工艺有关 ,制备片状晶粒的六铝酸钙材料需满足两个条件 :一是晶核有足够的发育空间 ,二是从晶核生长形成片状结构需足够的物质扩散。采用纯铝酸钙水泥和活性氧化铝为原料的试样 ,其CA6晶核很容易发育成片状晶形 ,且随着坯体成型压力的增加 ,片状CA6有向等轴状发展的趋势 ;采用     

烯（醚）醛一步法合成异戊二烯技术开发—基础理论研究进展

本文介绍了烯(醚)醛一步法合成异戊二烯技术开发中,基础理论研究工作的进展,其中包括化学热力学、化学动力学、再生烧炭本征动力学和扩散动力学等理论研究。并针对该反应特征进行了化学反应规律和流动传递规律的研究。建立了流化床反应器数模和流化床再生器数模,为工程技术开发提供理论依据。     

Platinum particle size effect on the oxidative dehydrogenation of aqueous ethanol

The effect of the platinum particle size was investigated for the catalytic oxidative dehydrogenation of aqueous ethanol to ethanal at a temperature of 303 K, an ethanol concentration of 260 mol m^–3, a partial oxygen pressure 60 kPa, a pH of 9, and an ethanal and ethanoate concentration of 20 mol m^–3. A particle size effect on the turnover frequency was observed but only for particle sizes smaller than 2 nm. Hence, the reaction shows a limited structure sensitivity.