聚硅氧烷-丙烯酸酯共聚物互改性产物的表面特性

通过测定参照液体在固体表面的接触角，计算固体的表面能及固体／液体接触体系的粘附功，考查了聚硅氧烷-丙烯酸酯共聚物互改性产物的表面特性及其对粘接性能影响。     

Zinc Coated Steel/Epoxy Adhesive Systems: Investigation of the Interfacial Zone by FTIR Spectroscopy

The present study takes advantage of the ability of Fourier Transform Infrared Spectroscopy (FTIR) for the analysis of ultrathin organic films on metals. FTIR in the reflection mode (IRRAS) is used in order to study the interaction of ultrathin films of dicyandiamide (hardener of most one-pack epoxy resins) with various substrates, model ones such as gold or zinc and industrial ones such as steel and zinc-coated steels.

Pure zinc surfaces and, to a lesser extent, zinc-coated steels are shown to react with dicyandiamide after heating at 180°C, as evidenced by the frequency shift of the absorption band (at about 2200 cm^-1) characteristic for nitrile groups. As real systems consist of thick layers of a fully formulated adhesive cured onto a metallic substrate, the direct investigation of such a buried interphase is no longer possible by FTIR and by most of the known spectroscopies. Some mechanically tested specimens are then analysed, after failure, by FTIR microspectrometry. The spectra obtained, corresponding to the fracture initiation zone which is about 100 μm in diameter, advocate for the presence of an ultrathin layer of modified polymer still covering the substrate.     

HEAT TRANSFER BETWEEN ROUGH SURFACES IN CONTACT OVER A HIGHLY ELLIPTICAL CONTOUR AREA: COMPARISON OF EXPERIMENTAL AND NUMERICAL RESULTS

This paper describes experimental and numerical studies of heat transfer between surfaces in contact over a highly elliptical area in a gas or in vacuum. Measurements of the steady-state thermal resistance of a high aspect ratio contact formed between cylindrical steel surfaces with widely different radii of curvature (76 cm vs 0.95 cm) are reported for two levels of surface roughness (0.05 μm and 1.0 μm rms) and compared to 3-D numerical results obtained with the multigrid method. Theoretical results obtained by evaluating the contact conductance acting over each surface element within the contour area with a method developed previously for rough but nominally flat surfaces are shown to be in excellent agreement with the rough surface experimental data.     

采用表面粘涂技术提高设备的抗腐蚀性能

通过表面粘涂，对受到腐蚀、冲蚀、气蚀的设备进行表面修补与防护，可提高设备的使用寿命。     

Carbon Aerogels as Electrode Material in Supercapacitors

Due to their large specific surface area and their high electrical conductivity carbon aerogels are promising materials for electrodes in electrochemical double-layer capacitors (supercapacitor). The carbon aerogels were made via pyrolysis of resorcinol formaldehyde aerogels. The latter were prepared by supercritical and subcritical drying as well. The important findings of our investigation were, that the highest capacities of 46 F/cm³ were measured for samples with a density of about 800 kg/m³ pyrolyzed at 800°C. Also it was shown that RF-gels with molar resorcinol/catalyst ratios 1000 or higher can be dried subcritically without cracking or significant shrinkage. Carbon aerogels derived from these RF-aerogels have a small mesopore surface area, however an especially large micropore area. They provide electrical capacities which are most suitable for their use in supercapacitors.     

Effect of particle size on the surface oxidation and flotation behavior of galena particles in lime system

ABSTRACT

In this research, the effect of particle size on the surface oxidation and flotation behavior of galena in the lime system was studied. Coarse (?0.074 + 0.038 mm), intermediate (?0.038 + 0.025 mm) and fine (?0.025 mm) galena particles were used in the experiment. The dissolution tests, flotation tests, and sorption tests were accomplished. Through further analysis by XPS, the effect of particle size and lime was observed. The decrease of mineral particle sizes increased the adsorption ratio of collector and the dissolution of galena, while the hydrophilic product OH^?/Ca(OH)⁺ produced by dissolution occupied the dominant position, which led to the minerals hydrophilic.     

溴虫腈土壤和甘蓝微量残留量的气相色谱法测定

采用气相色谱法定量分析溴虫腈土壤和甘蓝微量残留量。样品经丙酮提取 ,液 液分配及氧化铝柱层析法净化后 ,以GC ECD测定 ,DB 170 1毛细管柱 ,氮气为载气 ,柱温 2 6 0℃ ,汽化室温度 2 5 0℃ ,检测器温度 2 80℃ ,外标法定量。该方法快速、准确 ,在 0 0 1～ 2 0 0mg/L范围内线性相关系数r2 =0 9999,平均回收率 90 0 %～ 10 3 6 7% ,变异系数 4 4 8%～ 5 89% ,最小检测量 2× 10 12 g ,最低检出浓度 3 3× 10 4mg/kg。     

纳米碳酸钙的表面活化改性研究

本文主要介绍通过加入特定的表面改性剂,制得了表面改性的活性碳酸钙.并对活化过程中的一系列影响因素,如活化温度、活化时间、碳酸钙悬浊液浓度、表面改性剂用量进行了研究.     

改性活性炭的表面特性及其对苯酚的吸附性能

研究了表面改性对活性炭吸附苯酚性能的影响。研究发现,硫酸氧化可增加活性炭表面酸性基团的含量,提高了活性炭的表面亲水性,降低pHPZC值,因而对吸附水中的苯酚的性能产生明显影响,降低了对苯酚的吸附。