Municipal solid waste conversion to energy

In recent years it has been recognised by an increasing number of nations that there is considerable energy potential within MSW. As a result many countries have established R,D& D programmes to examine methods of exploiting this potential. The IEA's MSW Conversion Activity was set up in 1986 to provide an infrastructure for sharing information and co-ordinating work in this area internationally. This Activity was extended in 1989 and currently a total of 9 nations participate in it.

To cope with the wide scope of the area (encompassing both biological and thermal processing of MSW) the Activity was divided into three subgroups or Expert Working Groups (EWGs). Each of these dealt with a distinct area of expertise:

1. •Downstream effects of source separation and screening of MSW

2. •Sampling and analytical protocols

3. •Landfill gas

In addition to these groups a central secretariat based at Harwell (UK) has provided guidance, established and administered databases of contacts and produced a series of national reports.

This paper describes the achievements of the Activity and discusses work proposed for the future.     

Properties and Performance of Cation-Doped Ceria Electrolyte Materials in Solid Oxide Fuel Cell Applications

Cation-doped CeO₂ electrolyte has been evaluated in single-cell and short-stack tests in solid oxide fuel cell environments and applications. These results, along with conductivity measurements, indicate that an ionic transference number of ∼0.75 can be expected at 800°C. Single cells have shown a power density >350 mW/cm². Multicell stacks have demonstrated a peak performance of >100 mW/cm² at 700°C using metallic separators.     

Possibilities and extension of XRD material response analysis in failure research for the advanced evaluation of the damage level of Hertzian loaded components

Due to clearly distinguishable damage symptoms, it is differentiated between the surface and sub‐surface failure mode of rolling bearings. Material states red out by X‐ray diffraction (XRD) residual stress measurements point to a variety of loading conditions especially at raceway surfaces that are associated with several competing failure mechanisms. The corresponding lifetime reduction can range from the lower fatigue strength region to material ratcheting in extreme cases. Relevant position of the microstructural changes and nature of the failure mechanisms are characterized. The time alteration of the XRD material parameters measured at or near the surface and at the depth of the maximum equivalent stress correlates, in a different manner, with the statistical parameter of the 10 % bearing life. Both failure modes are illustrated by concrete examples. Contaminated lubricant and boundary lubrication, which represent practically important surface‐induced failures, are discussed in more detail. Gray staining, i.e. shallow pitting, often occurs without distinct indication of global material aging by means of XRD characteristics. Here, scanning electron microscopy observations and electron microprobe analyses point to corrosion fatigue as acting surface failure mechanism. The interaction between material and lubricant under complex loading regimes particularly of mixed friction and corrosion opens further failure research areas in the field of tribology.     

Non-steady-state model for kinetics of free radical polymerization, 4. Direct thermal initiation

This paper deals with the non-steady-state kinetics of direct thermal initiated polymerization. The initiation is assumed to be a bimolecular reaction of the monomer. The relationship between the radical concentration and the monomer conversion is rigorously derived. In further treatment a few very close approximations are introduced based on the fact that the number of monomer molecules reacting in the initiation step is much less than that consumed in the propagation step for a process producing high polymer, and the value of the rate constant for propagation or chain transfer is much lower than that for chain termination. Expressions for various molecular parameters, such as molecular weight distribution, number-average and weight-average degrees of polymerization, and dispersity, are given. Several numerical examples are provided.     

Influence of two-step process and of different stoichiometric ratios on morphologies generated in castor oil epoxy resins

Phase separation during polymerization was studied in a model system consisting of a diepoxide based on diglycidyl ether of bisphenol A (DGEBA), variable amounts of ethylenediamine (EDA) and the mass of castor oil (CO) necessary to obtain a mass fraction equal to 0-15 in a final system where the stoichiometric ratio of amine to epoxy equivalents, r, was equal to 1. A two-step polymerization process was performed by curing first a system with r = 0-5, during variable times before phase separation, and then carrying the system to r = 1. Thermodynamic analysis of samples with different r values led to a linear relationship between the Flory-Huggins interaction parameter and r. The concentration (P) and average size (D?) of dispersed-phase particles followed opposite trends, i.e. P increased while D? decreased, when either r was increased or the time of curing in the first step of a two-step process was decreased. This was explained by assuming that the competition between nucleation and growth was determined by the viscosity at the cloud point, η_cp. Low values of η_cp favoured growth over nucleation and led to fewer but larger particles.     

Complexity of the color appearance of objects with nonuniform illumination

An inversion relationship is clarified between lightness and brightness, and also between chroma and colorfulness under nonuniform illumination with different illuminance levels (high and low) within the same visual field. Brightness (or colorfulness) of object color with low lightness (or chroma) under high illuminance level is perceived higher than that of another object color with high lightness (or chroma) under low illuminance level. Two color images are given for showing the inversion phenomena on brightness–lightness and colorfulness–chroma between object colors under different illuminance levels. These color images are useful for making researchers on color understand the differences in concept between brightness and lightness, and also between colorfulness and chroma. In particular, the concept of colorfulness is important, but difficult to understand. © 2007 Wiley Periodicals, Inc. Col Res Appl, 32, 372–377, 2007     

New method for measuring an optical property of a sample treated by FWA

In this article, a new method for measuring a total spectral radiance factor of a FWA‐treated sample illuminated by a specific standard illuminant is introduced. The method replaces an unstable real fluorescent standard by a bi‐spectral luminescent radiance factor data, which works as a virtual fluorescent standard (VFS) by knowing spectral intensity distributions of illuminations applied to the sample. The method utilizes two illuminations I₁ and I₂ whose relative spectral intensity distributions are different from each other and synthesizes a virtual illumination presenting the identical fluorescent spectral radiance factor to that presented by the standard illuminant with the VFS of the specific bi‐spectral luminescent radiance factor by linearly combining I₁ and I₂ with the suitable weighting factors. The applicability of the method is examined in principle by comparing ISO brightness and CIE whiteness index of fluorescent standard paper as a test sample obtained by this new method to the assigned values. © 2007 Wiley Periodicals, Inc. Col Res Appl, 32, 195–200, 2007     

A unified proposal for characteristic testing methods and figure of merit of 8‐kV/3.5‐kVA class light‐triggered thyristors

Power devices with high capability have been developed. 8‐kV/3.5‐kA‐class light‐triggered thyristors have the highest capability among power devices. These devices are used in the Kii Channel HVDC transmission system in Japan. In this paper, we report the extracted problems of conventional testing methods of 8‐kV/3.5‐kA‐class light‐triggered thyristors among manufacturers, and the proposed unified testing methods on the basis of element characteristics and operating conditions in the Kii Channel HVDC system. Furthermore, we propose a figure of merit for power devices for the practical use, and try to extract elements used at the Kii Channel HVDC system with small margins and low withstand capabilities. © 2002 Wiley Periodicals, Inc. Electr Eng Jpn, 140(3): 61–70, 2002; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.10024     

Lyapunov‐stable discrete‐time model reference adaptive control

Discrete‐time model reference adaptive control (MRAC) is considered with both least squares and projection algorithm parameter identification. For both cases complete Lyapunov proofs are given for stability and convergence. The results extend the approach of Johansson (Int. J. Control 1989; 50 (3):859–869) to include Lyapunov stability for MRAC when the normalized projection algorithm is used for parameter identification. Copyright © 2005 John Wiley & Sons, Ltd.