一种蒸发式冷凝器的新型设计方法

蒸发式冷凝器设计方法的粗糙和繁琐限制其广泛应用,特别是限制其应用于民用和小型商用建筑中。针对上述问题,作者通过实验研究了蒸发式冷凝器的影响因素（进风湿球温度、最小截面风速和喷淋水量）对蒸发式冷凝器热质交换的影响。同时提出了一种新型设计方法,此方法简单,精度较高。适合工程设计、选型和生产应用。     

铝活塞余热淬火和自然时效的应用研究

图 1所示的活塞试件 ,在开型时间为 5 0s～ 5 5s时 ,其表面温度为 (4 90± 5 )℃ ,可满足淬火要求。自然时效时间为 2 4天时 ,其机械性能可达到国标技术要求。这种新工艺有明显的经济效益。     

空分设备的酸性腐蚀及预防

以切换式换热器空分设备为例 ,分析了空分设备酸性腐蚀的原因、可能造成的危害 ,提出了预防措施。     

交联型聚醚聚氨酯的表征、力学性能及其碱金属盐络合物的导电性能

采用三羟甲基丙烷（ＴＭＰ）作交联剂与聚乙二醇（ＰＥＯ－１５４０）和甲苯二异氰酸酯（ＴＤＩ）反应，得到了具有较好力学性能的交联型聚醚聚氨酯（ＰＥＵ），该聚合物与ＬｉＣｌＯ４的结合物具有较高的室温电导率（σ３０℃＝１．８７×１０￣（－４）Ｓ／ｃｍ）。采用全反射红外光谱（ＡＴＲ－ＩＲ）对聚合物的结构进行了表征。对聚合物的组成、不同ＴＤＩ类型及络合盐浓度对聚合物力学性能及其络合物电导率的影响进行了探讨。低度交联聚合物的络合物，其电导率与温度的关系符合建立在自由体积理论上的ＶＴＦ方程，表明络合物中离子的传导主要是在无定形区域进行，与自由体积有关。     

导汽箱产生长裂纹和大面积凹陷原因分析、处理及预防对策

对硫酸废热锅炉锅筒内自然循环的导汽箱产生长裂纹和大面积凹陷的原因作了分析，提出处理该缺陷的方法，确保了锅炉的安全运行，并提高了蒸汽的品质。     

热强钛合金BT25组织与性能

介绍了前苏联航空发动机用热强钛合金（或高温钛合金）BT25的发展概况，并对BT25合金的成分特点、热处理强化优点等做了进一步阐述，给出了退火状态下的物理性能，在说明热强钛合金微观组织与力学性能关系的基础上给出了BT25合金的各种力学性能。     

Discrete Modeling and Suggested Measurement of Heat Transfer in Gas-Solids Flows

This article presents a two-dimensional transient model for gas-solids flow and heat transfer through pipes using the coupled Computational Fluid Dynamics and Discrete Element Method approach. Numerical simulations have been conducted to examine the modification of fluid thermal structure due to the presence of particles in a pneumatic transport pipeline. Modeled results have demonstrated the key role of transversal motion of rebounding particles in the pipe cross section in altering fluid temperature. Further implementation of this modeling technique in air-drying processes is discussed and possible experimental methods for the measurement of in situ particle and fluid motion and temperature profile are cited.     

A numerical model for induction heating processes coupling electromagnetism and thermomechanics

This paper presents a mathematical and numerical model developed for coupling the various physical phenomena (electromagnetic, thermal and mechanical) taking place in axisymmetrical induction heating processes. All three electromagnetic, thermal and mechanical models are time dependent and take full account of the electromagnetic and thermal non‐linear effect especially with magnetic materials. The electromagnetic problem is discretized and solved in the workpiece, air and inductors. The heat transfer equation and the mechanical equilibrium equations are solved in the workpiece only, both using a finite element method. The mechanical model can take into account thermoelastic–plastic behaviour for the part. The model has been successfully applied to several cases of induction heating. Comparisons between numerical and experimental results show an excellent agreement. Copyright © 2003 John Wiley & Sons, Ltd.     

Extraction of penicillin G from simulated media by an emulsion liquid membrane process

The extraction of penicillin G from simulated media was performed by water/oil/water (w/o/w) emulsion liquid membranes (ELMs) and studied under various operational conditions in a batch system. The degree of extraction achieved was between 80% and 95% under specific conditions. A concentration of greater than nine times the initial concentration of penicillin G in the external phase was obtained in the internal phase. The pH of the internal aqueous solution, containing a basic salt, was theoretically calculated on the basis of the amount of penicillin G transported into the internal phase. The calculated results agreed with the experimental data well and were used to select a suitable type and concentration of a basic salt in the internal phase to give a pH within the range 5 to 8 where penicillin G was stable after the termination of extraction. The extraction of penicillin G was successfully performed by the ELM process with sodium carbonate in the internal phase.