FCC汽油叠合生产柴油的研究——(Ⅰ)叠合催化剂的研制

采用中孔γ-Al2O3为载体，以非贵金属Ni为活性金属组分，以金属Sn为助剂组分，制备了FCC汽油叠合生产柴油的催化剂。在实验室小型连续流动式固定床装置上，以FCC汽油为原料，考察了主活性金属负载量、助催化剂、催化剂制备条件对催化剂性能的影响。研究结果表明，在活性金属Ni质量分数为8％，助催化剂Sn质量分数为1％，浸渍时间6h，焙烧温度500℃，焙烧时间4h的条件下，制备的叠合催化剂的催化性能最好。并对催化剂进行了1500h的稳定性试验和再生性能考察，结果表明该叠合催化剂具有良好的稳定性和再生性能。     

膜电极结构对质子交换膜燃料电池性能的影响

膜电极(MEA)作为质子交换膜燃料电池(PEMFC)的核心组件之一，其结构和组成对电池的性能有着重要的影响。提高膜电极性能的一个重要的指导思想是在催化粒子的周围形成良好的质子、电子和气体通道。以此为主线，从电极制备工艺的发展历程，Nafion的使用与质子通道的改进、电子通道的改进、阴极催化等几个方面详细地总结和讨论了近年来MEA的研究状况，并在此基础上对MEA的进一步研究提出了若干建议。     

Cu-Mg/Al_2O_3催化乙醇和乙二胺合成N-乙基乙二胺

在固定床反应器内,乙醇和乙二胺经分子间催化胺化反应合成了N-乙基乙二胺(NEED),考察了一系列铜系催化剂的活性,并筛选出催化性能较好的Cu-Mg/A l2O3催化剂;通过X射线衍射和透射扫描电子显微镜方法表征了助剂Mg对Cu/A l2O3催化剂的改性作用;考察了助催化剂Mg含量、反应温度、反应压力、进料量和乙二胺含量等对Cu-Mg/A l2O3催化剂性能的影响。实验结果表明,Cu-Mg/A l2O3催化剂具有很好的活性和选择性;在200℃、3.0MPa、质量分数20%的乙二胺乙醇溶液、进料量1.0mL/m in的条件下,乙二胺的转化率为71.56%,产物NEED的选择性和收率分别为92.62%和69.86%;经过20 d的连续使用表明,Cu-Mg/A l2O3催化剂具有良好的稳定性。     

井下乳化/水热催化裂解复合降黏开采稠油技术研究

实验考察了胜利孤东稠油井下催化水热裂解和乳化/催化水热裂解降黏效果。所用催化剂为水溶性铁镍钒体系,Fe3+∶Ni2+∶VO4+=5∶1∶1,100 g稠油与30 g 0.5%催化剂水溶液在240℃反应24小时。原始黏度(50℃)11.0和8.36 Pa.s的两种稠油裂解并静置除水后,黏度降低76.2%和75.6%,室温放置60天后降黏率下降小于3个百分点,气相色谱显示裂解后轻组分明显增加,红外光谱显示稠油组分发生脱羧反应且芳环数减少。讨论了稠油催化水热裂解反应机理。所用化学助剂JN-A在油水中均可溶,耐温达250℃,耐矿化度达50 g/L,其水溶液以30∶100的质量比与稠油混合时形成低黏度的O/W乳状液。当水相含1.0%JN-A和0.5%催化剂时,两种稠油水热裂解后的反应混合物为O/W乳状液,黏度仅为319和309 mPa.s,静置除水后的稠油降黏率增加到86.5%和87.3%,其中的轻组分含量进一步增加。该井下乳化/催化水热裂解复合降黏法成功地用于孤东两口蒸汽吞吐井,稠油井作业后初期采出的原油黏度由~9 Pa.s降低到1 Pa.s左右,随采油时间延长而逐渐升高,约50天后超过4Pa.s。图2表6参5。     

Effect of oxygenation on electrocatalysis of La0.6Ca0.4CoO3−x in bifunctional air electrode

A vacuum-annealed La_0.6Ca_0.4CoO_3−x was consecutively oxygenated in air at temperatures decreasing from 800 to 100 °C, and its electrocatalytic activities for oxygen reduction and evolution were then measured as a function of the oxygenation temperature. The valence of Co cation, changing between +2 and +3, was found susceptible to annealing either in vacuum or air. The catalytic activities initially decrease monotonically as the oxygenation temperature was decreased from 800 to 300 °C, as a result of increasing oxygen content, and then rise abruptly with the oxygen reduction activity reaching a maximum at 200 °C and the oxidation activity at 150 °C. X-ray photoelectron spectroscopy analysis indicated that the enhancements by the low-temperature oxygenation involved increased OH coverage and less charged cations at surface. The results clearly reveal the importance of the post-calcination annealing process for optimizing the performance of La_0.6Ca_0.4CoO_3−x in air electrode applications.     

基于SOI的双极场效应晶体管

在分析了双极型晶体管和场效应晶体管各自的特点和不足后，介绍了一种既具有双极型晶体管较大电流容量和功率输出，又具有场效应晶体管高输入阻抗的电子器件——双极MOS场效应晶体管(BJMOSFET)，同时指出体硅BJMOSFET的阳极扩散区与衬底之间存在较大的漏电流，可产生较大的寄生效应。提出了一种新型固体电子器件——基于SOI的BJMOSFET，分析了其工作原理j与体硅BJMOSFET比较，由于SOI技术完整的介质隔离避免了体硅器件中存在的大部分寄生效应，使基于SOI的BJMOSFET在体效应、热载流子效应、寄生电容、短沟道效应和闩锁效应等方面具有更优良的特性。     

天然气空气绝热转化制合成气催化剂研究

制备了天然气空气绝热转化催化剂,采用固定床反应器进行稳定性评价试验,对反应前后的催化剂进行了分析表征。结果说明,天然气和空气绝热转化反应放热形成的高温对催化剂有烧结作用,使催化剂晶体结构发生了变化,起活性作用的金属镍和氧化铝载体转化为镍铝尖晶石结构的物质。进一步的试验表明,在1050～1300℃的温度可以把催化剂的晶体结构改变。     

KOAc/NaY催化合成邻甲基苯甲醚

以KOA c/NaY为催化剂,在连续流动固定床反应器内,邻甲基苯酚(OC)与碳酸二甲酯(DMC)经过气固相催化反应合成了邻甲基苯甲醚(OM)。考察了内、外扩散对KOA c/NaY催化剂活性的影响。实验结果表明,当气流线速度大于30cm/m in时可消除外扩散对合成反应的影响;当KOA c/NaY催化剂的平均粒径在0.30~0.75mm(20~80目的颗粒)时能消除内扩散对合成反应的影响。在消除内、外扩散效应后,还考察了反应温度、原料配比、空速对合成反应的影响,得到较佳的反应条件:催化剂5mL,反应温度548K,反应压力0.6M Pa,空速0.6h-1,n(DMC)∶n(OC)=1,在线评价时间7h。在此条件下,OC的转化率高达85.7%,OM的选择性大于99%。     

Electro-organic synthesis without supporting electrolyte: Possibilities of solid polymer electrolyte technology

The application of ion exchange membranes as solid polymer electrolytes (SPE) in fuel cells is state-of-the-art. This technology needs no supporting electrolyte; consequently it can be applied for electro-organic syntheses in order to save process steps. In this case the process is not predetermined to a maximized energy efficiency so that the selection of the cell design, of the electrode materials and of the operating conditions can be focused on a high selectivity of the electrode reactions. The electro-osmotic stream, which is caused by the solvation shells of the ions during their migration through the membrane, and hence is a typical property of SPE technology, has a significant effect on the electrode reactions. It generates enhanced mass transfer at the electrodes, which is beneficial for reaction selectivity. It can be influenced by the choice of, and possibly by the preparation of, the membrane. An additional remarkable advantage of SPE technology is the exceptional long durability of oxide coated electrodes. By combination of several process engineering methods stable operation of SPE cells has been realized, even for examples of non-aqueous reaction systems. Experiments up to 6000 h duration and in cells of up to 250 cm² membrane area show the potential for industrial application.