可与氟树脂基板相匹敌的热可塑性树脂基板材料

概述了可以与氟树脂基板相匹敌的低介质特性的热可塑性树脂基板材料的开发和应用。     

Anhydrous esterification of myristic acid with propylene: Ion exchange resin and acid-treated clay as catalysts

Anhydrous esterification of myristic acid with propylene was carried out in the temperature range of 110–145°C and pressure from 190–195 psig in the presence of Amberlyst-15 (cation exchange resin) and Filtrol-24 (acid-treated clay) as catalysts. The product ester, isopropyl myristate finds use in cosmetic and topical medicinal preparations where good absorption through the skin is desired. Filtrol-24 is the catalyst of choice, and the recommended operating temperature is 130°C with a pressure of 190 psig.     

The effects of glycol methacrylate as a dehydrating agent on the dimensional changes of liver tissue

The dimensional changes of liver sections during the course of processing with glycol methacrylate (GMA) or with ethanol are described. Tissue processing with ethanol served as a control. During prolonged processing steps (24 h each), linear shrinkage of tissue specimens dehydrated with GMA at room temperature was 13.2%. Subsequent infiltration with GMA resulted in trivial swelling, and polymerization in slight shrinkage (2.3%). In comparison, processing with cold GMA resulted in shrinkage during dehydration (about 10.8%), a slight swelling in pure GMA, followed by shrinkage during polymerization (2.2%). Short routine processing schedules resulted in similar shrinkage/swelling patterns, although precise values differed slightly. In all experiments, ethanolic dehydration resulted in smaller dimensional tissue changes than did GMA dehydration. The dimensional changes of tissue sections during stretching on water, mounting and drying compensated for the major part of the shrinkage manifested during processing.     

某炼油厂一级浮床除盐系统阳床工艺特性及调整试验

论述了某厂一级除盐系统阳床工艺特性及调整试验过程，对存在问题进行分析并改进，得到了实际运行最佳方式和参数，取得良好效果。     

Phenol novolac/poly(4- hydroxyphenylmaleimide) blend hardeners for DGEBA-type epoxy resin

Phenol novolac/poly (4-hydroxyphenylmaleimide) (PHPMI) blends were used as an epoxy resin hardener. The curing behavior of the above system and the thermal and mechanical properties of the cured epoxy resin were studied. It was not necessary to use a curing accelerator for this system, because PHPMI caused acceleration of the curing reaction. The curing mechanism of this system was investigated by using model compounds. Test pieces from the neat resins and the glass fiber reinforced resins were evaluated in terms of thermal and mechanical properties, respectively. It was found that heat resistance and mechanical properties were improved by increasing the amount of PHPMI in the hardener.     

In－BiCaVIG的晶体生长与性能

本文报导了用助熔剂法成功地生长大尺寸掺铟ＢｉＣａＶＩＧ晶体的方法以及实验结果，介绍了该单晶在近红外区的磁光器件中的重要应用。     

桐油改性酚醛树脂的结构及固化过程的研究

通过桐油与苯酚在酸性催化剂存在下反应，然后再在碱性催化剂存在与甲醛反应制得了一种热固性桐油改性酚醛树脂。利用红外光谱，差示扫描量热法分析技术对改性树脂的结构及固化反应过程进行了研究。     

Relaxation phenomena caused by equilibration of point defects

Relaxation phenomena due to equilibration of point defects in metals are reviewed. The relaxation effect in specific heat observed in tungsten and platinum confirms that in both cases the nonlinear increase in the high-temperature specific heat has to be attributed to point-defect formation. Relaxation phenomena observed by measurements of electrical resistivity and positron annihilation are also considered. The comparison of the data seems to be favorable for the conclusion that all the phenomena are of one origin.     

新型环氧树脂绝缘浸渍胶（WSK）在微特电机上的应用

介绍了新型环氧树脂少溶剂快干绝缘浸渍胶的性能试验数据及基在微特电机上的应用及注意事项。