A new monitoring system for piping systems in fossil fired power plants

A CEC-funded project has been performed to tackle the problem of producing an advanced Life Monitoring System (LMS) which would calculate the creep and fatigue damage experienced by high temperature pipework components. Four areas were identified where existing Life Monitoring System technology could be improved:

1. 1. the inclusion of creep relaxation

2. 2. the inclusion of external loads on components

3. 3. a more accurate method of calculating thermal stresses due to temperature transients

4. 4. the inclusion of high cycle fatigue terms.

The creep relaxation problem was solved using stress reduction factors in an analytical in-elastic stress calculation. The stress reduction factors were produced for a number of common geometries and materials by means of non-linear finite element analysis. External loads were catered for by producing influence coefficients from in-elastic analysis of the particular piping system and using them to calculate bending moments at critical positions on the pipework from load and displacement measurements made at the convenient points at the pipework. The thermal stress problem was solved by producing a completely new solution based on Green's Function and Fast Fourier transforms. This allowed the thermal stress in a complex component to be calculated from simple non-intrusive thermocouple measurements made on the outside of the component. The high-cycle fatigue problem was dealt with precalculating the fatigue damage associated with standard transients and adding this damage to cumulative total when a transient occurred.

The site testing provided good practical experience and showed up problems which would not otherwise have been detected.     

渣油中硫化物类型分布与化学转化性能

用X射线光电子能谱（XPS）定量研究了Athabasca渣油及其加氢裂化渣油，流化焦化渣油中的硫化物类型，用超临界流体萃取分馏将3种渣油分别分离成9－14个窄馏分及残渣，测定其中的硫醚，噻吩，亚砜和砜类硫原子的分布，讨论了加氢裂化和热裂化反应脱除硫化物的反应性能。     

Energy use in controlled temperature marine aquaculture

Temperature control offers benefits in land‐based marine aquaculture: stock growth rates may be enhanced by heating in winter; mortality rates in summer may be reduced by cooling. However, if the plant is not well designed, temperature control may create very large energy demands. This paper describes the application of temperature control in abalone aquaculture in New Zealand, with a focus on energy considerations in plant design. An abalone farm using a semi‐closed water conditioning system is used as a case study for which an energy model, based on a heat pump system, is developed. The model is used to determine the impact of plant design and tank conditions on the economics of the operation. Copyright © 2002 John Wiley & Sons, Ltd.     

Measurement of Thermal Diffusivity at Low Temperatures Using an Optical Reflectivity Technique

An experimental arrangement has been developed for measuring the transient temperature responses and the thermal diffusivities of foil materials in the range of 10 to 300K by using the optical reflectivity technique. The cryogenic system with optical windows is designed to provide temperatures from 10 to 300 K. The front surface of a foil specimen is heated by a pulsed Nd:YAG laser. In situ measurement of the reflectivity of a continuous-wave He–Ne laser at the rear surface is conducted on the microsecond time scale. Using the temperature dependence of reflectivity, the transient temperature response is deduced. The thermal diffusivity is obtained by fitting Parker's formulae to the experimental data on temperature rise. Stainless-steel foils are chosen as samples and are studied in the region from 10 to 300 K. The accuracy is examined by comparing the present results with the theoretical temperature responses and thermal diffusivity data from the literature. Good agreement is observed.     

Si基膜片型气敏传感器微结构单元的热学性能

微结构气敏传感器由于其微型化、低功耗、易阵列化和易批量生产等优点而受到国内外研究者的广泛关注。利用微机电系统（MEMS）加工技术，制备Si基膜片型微结构单元，并分析其热学性能。这种单元工作区温度为-300℃时，加热功率约75mW；并且膜片工作区的热质量很小，温度可以于毫秒量级的时间内，在室温和450℃之间调制。利用这种微结构单元，可以在温度调制方式下，研究气敏薄膜的电学特性和敏感机理。     

Si衬底上Ta-N/Cu薄膜性能研究

对Si衬底上Ta-N/Cu薄膜进行了电学和热学分析，结果发现500℃以下薄膜电随几乎不变，600-690℃下的退火引起的电阻率降低是由于Ta-N电阻的热氧化和Cu熔化扩散引起的，而690℃以上的电阻率增加是由于Cu引线传输能力减弱所致，为0.18μm以下的超大规模集成电路中的Cu引线和电阻薄膜的制作提供了有益的借鉴。     

NO emission characteristics in counterflow diffusion flame of blended fuel of H2/CO2/Ar

Flame structure and NO emission characteristics in counterflow diffusion flame of blended fuel of H₂/CO₂/Ar have been numerically simulated with detailed chemistry. The combination of H₂, CO₂ and Ar as fuel is selected to clearly display the contribution of hydrocarbon products to flame structure and NO emission characteristics due to the breakdown of CO₂. A radiative heat loss term is involved to correctly describe the flame dynamics especially at low strain rates. The detailed chemistry adopts the reaction mechanism of GRI 2.11, which consists of 49 species and 279 elementary reactions. All mechanisms including thermal, NO₂, N₂O and Fenimore are taken into account to separately evaluate the effects of CO₂ addition on NO emission characteristics. The increase of added CO₂ quantity causes flame temperature to fall since at high strain rates a diluent effect is prevailing and at low strain rates the breakdown of CO₂ produces relatively populous hydrocarbon products and thus the existence of hydrocarbon products inhibits chain branching. It is also found that the contribution of NO production by N₂O and NO₂ mechanisms are negligible and that thermal mechanism is concentrated on only the reaction zone. As strain rate and CO₂ quantity increase, NO production is remarkably augmented. Copyright © 2002 John Wiley & Sons, Ltd.     

几种高级便携式打印机性能特点比较

本文是对市场上几款高级便携式打印机主要性能特点的比较考察报告，包括：佳能生产的CanonBJC-70型便携式彩色喷墨打印机，惠普生产的HPDeskJet340型便携式彩色喷墨打印机和Pentax生产的Pentax PocketJet便携式打印机，后者必须使用热敏纸。     

Physico-chemical properties of ceramic pigments for high-temperature application

Heat resistant coatings are required primarily for stacks, exhaust pipes, reactors, space crafts and similar equipments that are permanently or occasionally exposed to elevated temperatures. High-temperature coatings are generally based on silicone resin with ceramic and metallic pigments. In this study, iron oxide, cobalt oxide (thermo chromic compound) and aluminum oxide are used for the preparation of four new types of coloured pigments. The thermal resistant characteristics of these ceramic pigments were studied by differential thermal analysis, thermo gravimetric analysis and differential scanning calorimetric analysis. These ceramic pigments are found to be thermally stable up to 400 °C.