SO2转化温度异常情况分析

结合凤山实业总公司硫酸车间 SO2 转化系统的具体工艺流程 ,分析近几年转化系统出现温度不正常的原因 ,提出解决方法     

Structural acrylic adhesives for the sheet steel fabrication industries

Recent developments in rubber-toughened structural acrylic adhesives now offer sheet steel fabricators the opportunity to replace conventional metal fastening techniques such as spot welding with lower cost, durable, more versatile structural adhesive bonding. These developments, in particular much improved ability to bond oily/waxy surfaces common to the motor car industry and improved retention of fracture toughness after exposure to paint stoving temperatures, are discussed in this paper.     

含葡萄糖基水溶性硫化黑的合成

本文以C.I.硫化黑1为原料,经葡萄糖还原成隐色体后,再与葡萄糖缩合,合成出含葡萄糖基水溶性硫化黑。合成方法分别采用了焙烘法和水介质中合成。结果表明,水介质中合成的含葡萄糖基水溶性硫化黑溶解度好于焙烘法。     

用膜电解法处理低浓度SO2吸收液的三室电解槽材料的选择

提出了用膜电解法处理低浓度SO2吸收液的方法，介绍了三室电解槽的设计原理及在电场作用下，电解槽内离子的迁移和电解反应机理，系统地讨论了电解槽组成单元材料（如阳离子交换器）的选择及在H2SO4－NaHSO3-Na2SO3体系中金属阳极的选择等，并进行了试验验证，得到了很好的结果。     

Adhesive element modelling and weighted static shape control of composite plates with piezoelectric actuator patches

A novel finite element model is presented for static and dynamic analysis of composite plates integrated with a laminated piezoelectric layer, a host laminated composite plate and an adhesive layer between them. A new adhesive element is developed which includes both peel and shear effects in the adhesive layer based on first‐order shear deformation plate theory. The thin adhesive layer between the piezoelectric layer and the host plate is modelled by assuming that it carries constant shear and peel strains throughout its thickness. In addition, a weighted static shape control scheme for finding the optimal voltage distribution for static shape control is given. By selecting different weighting matrices, a variety of items such as displacements, slopes, curvatures, strains and even generalized forces, can be included in finding the optimal actuating voltage for static shape control. The present model is validated by comparing with those results available in the literature. The numerical results show that the weighted linear least method can give a satisfactory voltage distribution to best match the desired shape. Copyright © 2004 John Wiley & Sons, Ltd.     

一种环氧树脂阻尼灌封胶的热氧加速老化研究

研究了某种环氧树脂阻尼灌封胶在热氧老化的作用下分子结构、硬度、断面形貌以及动态力学性能随时间的变化．傅立叶红外光谱图表明，所制备的样品环氧基团反应比较完全，热氧老化后试样表面由仲胺和环氧基团形成的酯键发生了部分断裂和氧化；邵氏硬度的增加、瓦向高温区移动则表明在老化过程中复杂的固化反应仍然继续进行；最大损耗因子（tanδmax）波动较小表明试样老化后分子结构几乎保持不变；SEM图片显示试样的冲击断裂由老化前的韧性转变为老化后的脆性断裂．     

Simultaneous sulfide and acetate oxidation under denitrifying conditions using an inverse fluidized bed reactor

BACKGROUND: Simultaneous removal of sulfur, nitrogen and carbon compounds from wastewaters is a commercially important biological process. The objective was to evaluate the influence of the CH₃COO^?/NO₃^? molar ratio on the sulfide oxidation process using an inverse fluidized bed reactor (IFBR). RESULTS: Three molar ratios of CH₃COO^?/NO₃^? (0.85, 0.72 and 0.62) with a constant S^2?/NO₃^? molar ratio of 0.13 were evaluated. At a CH₃COO^?/NO₃^? molar ratio of 0.85, the nitrate, acetate and sulfide removal efficiencies were approximately 100%. The N₂ yield (g N₂ g^?1 NO₃^?‐N consumed) was 0.81. Acetate was mineralized, resulting in a yield of 0.65 g inorganic‐C g^?1 CH₃COO^?‐C consumed. Sulfide was partially oxidized to S⁰, and 71% of the S^2? consumed was recovered as elemental sulfur by a settler installed in the IFBR. At a CH₃COO^?/NO₃^? molar ratio of 0.72, the efficiencies of nitrate, acetate and sulfide consumption were of 100%, with N₂ and inorganic‐C yields of 0.84 and 0.69, respectively. The sulfide was recovered as sulfate instead of S⁰, with a yield of 0.92 g SO₄^2?‐S g^?1 S^2? consumed. CONCLUSIONS: The CH₃COO^?/NO₃^? molar ratio was shown to be an important parameter that can be used to control the fate of sulfide oxidation to either S⁰ or sulfate. In this study, the potential of denitrification for the simultaneous removal of organic matter, sulfide and nitrate from wastewaters was demonstrated, obtaining CO₂, S⁰ and N₂ as the major end products. Copyright © 2008 Society of Chemical Industry     

服装低密度聚乙烯热熔胶化学粉碎的研究

服装粘合衬布的生产需要低密度聚乙烯热熔胶的微细粉末,介绍了对该热熔胶的化学粉碎技术所进行的实验研究,表明采用适当的助剂种类和用量以及适宜的工艺过程,通过化学粉碎可以得到合格的粉末产品。     

Finite-element analysis and experimental study on tensile fatigue behaviour of bitumen–stone adhesion

Tensile fatigue behaviours of bitumen–stone adhesion were investigated using a dynamic mechanics analyser under stress‐controlled mode at two temperatures of 5 and 25°C and various controlled‐stress levels. Failure characteristics including interfacial failure and cohesive failure were examined using image analysis of fracture surfaces. Finite‐element analysis on stress distributions was conducted under different temperatures, film thickness and interfacial bonding conditions. A Coulomb–Mohr like criterion in combination with shear and normal stresses is proposed to deal with the extreme thin adhesive layer, which can be further simplified into an adhesive zone without significant loss of accuracy for stress analysis.     

PMMA／PBA乳胶IPN阻尼材料的研究

用乳液聚合方法合成了一系列的互穿聚合物网络，其中包括：ＰＭＭＡ／ＰＢＡ和Ｐ（ＭＭＡ－ｃｏ－ＰＭＡ）／ＰＢＡ乳胶互穿聚合物网络（ＬＩＰＮ），ＰＭＭＡ／ＰＢＡ乳胶双向互穿聚合物网络（ＬＢＩＰＮ）以及ＰＭＭＡ／ＰＢＡ界面交联互穿聚合物网络（ＩＣＬＩＰＮ）。动态力学谱和拉伸试验结果表明：（１）ＰＭＭＡ／ＰＢＡ互穿聚合物网络的两组分相容性和阻尼性能可通过ＭＭＡ和ＰＭＡ共聚来改善；（２）双向互穿技术是一种行之