混凝土结构的压电声波检测分析

本文介绍了混凝土结构的压电体波和表面波检测的主要进展,对两种压电声波检测的优缺点进行了总结。体波检测设备一般埋入混凝土内部,需要选择合理的检测部位,检测结果较为精确;声表面波检测无需选择特定的部位,但是检测深度有限。在实际检测工作过程中,可以联合两种方法相互验证。     

基于局部分型面的电器外壳注塑模具设计

电器外壳制品形状结构复杂,有两处侧凸(孔)较难处理。通过对矩形孔内侧凸的结构分析,在其局部设计了分型面,避免了使用侧向抽芯机构;对侧孔部位设计了斜顶杆侧向抽芯机构,其结构简单、紧凑。模具采用一模二腔、平衡式布局,采用经扁推杆由制品内部进料的潜伏式浇口,S型流道。在NX 8.0中完成了模具结构设计。经实践证明,该模具结构合理,产品合格。     

Constructing developable surfaces by wrapping cones and cylinders

We model developable surfaces by wrapping a planar figure around cones and cylinders. Complicated developables can be constructed by successive mappings using cones and cylinders of different sizes and shapes. We also propose an intuitive control mechanism, which allows a user to select an arbitrary point on the planar figure and move it to a new position. Numerical techniques are then used to find a cone or cylinder that produces the required mapping. Several examples demonstrate the effectiveness of our technique.     

A design of experiments investigation into dry separation using a Knelson Concentrator

Enhanced gravity, or centrifugal, separators have revolutionised gold processing over the past decades, significantly increasing the recovery of fine (−100 μm) free gold. One of the main drawbacks of centrifugal gravity concentrators is the large volume of water required (even if it is all recycled). With water becoming an ever increasingly important “commodity”, reducing this is of importance both from an environmental and a monetary point of view. This work investigated operating a laboratory scale Knelson Concentrator with a dry feed and using air as the fluidising medium. The feed used was a synthetic mixture of tungsten and quartz, used to mimic a gold ore. The response surface method and central composite design techniques were used to design the experiments and to model the results, with the experimental variables being the bowl speed (G-Level), air fluidising pressure and the feed rate. The models corresponded well to the experimental results, indicating that for this experimental setup, the optimal conditions were a bowl G-Level of 40 G, a feed rate of 220 g/min and an air fluidising pressure of 8 psi.     

Indoor heterogeneous photochemistry of furfural drives emissions of nitrous acid

People spend approximately 80% of their time indoor, making the understanding of the indoor chemistry an important task for safety. The high surface-area-to-volume ratio characteristic of indoor environments leads the semi-volatile organic compounds (sVOCs) to deposit on the surfaces. Using a long path absorption photometer (LOPAP), this work investigates the formation of nitrous acid (HONO) through the photochemistry of adsorbed nitrate anions and its enhancement by the presence of furfural. Using a high-resolution proton-transfer-reaction time-of-flight mass spectrometer (PTR-TOF-MS), this work also investigates the surface emissions of VOCs from irradiated films of furfural and a mix of furfural and nitrate anions. Among the emitted VOCs, 2(5H)-furanone/2-Butenedial was observed at high concentrations, leading to maleic anhydride formation after UV irradiation. Moreover, the addition of potassium nitrate to the film formed NO_x and HONO concentrations up to 10 ppb, which scales to ca. 4 ppb for realistic indoor conditions. This work helps to understand the high levels of HONO and NO_x measured indoors.     

A computer aided design method for car form and its application based on shape parameters

In the early design stage, automotive modeling should both meet the requirements of aesthetics and engineering. Therefore, a vehicle CAD (computer aided design) model that can be easily adjusted by feedbacks is necessary. Based on CE-Bézier surface, this paper presents a set of algorithms for parametric segmentation and fairing surface generation in a car model. This model is defined by a simplified automotive template and relevant control points, shape parameters and segmentation parameters, which can be modified to alter the car form efficiently. With this model and the corresponding adjustment method, more than fifty various vehicle models are established in this research according to different parameters. And two methods for calculating similarity index between car models are constructed, which are suitable for brand design trend analysis and modelling design decisionmaking.     

CFD Modeling of Active Volume Creation in a Non‐Newtonian Fluid Agitated by Submerged Recirculating Jets

Computational fluid dynamics (CFD) models were employed to investigate flow conditions inside a model reactor in which yield stress non‐Newtonian liquid is mobilized using submerged recirculating jets. The simulation results agree well with the experimental results of active volume in the reactor obtained using flow visualization by the authors in a previous study. The models developed are capable of predicting a critical jet velocity (v_c) that determines the extent of active volume obtained due to jet mixing. The v_c values are influenced both by the rheological properties of the liquid and the nozzle orientation. The liquid with higher effective viscosity leads to higher v_c for a downward facing injection nozzle. However, an upward facing injection nozzle along with a downward facing suction nozzle generates enhanced complementary flow fields which overcome the rheological constraints of the liquid and lead to lower v_c.     

平面桁架构建的定日镜面形支撑结构优化及实验

针对反射面成型的复杂影响因素，提出平面桁架构建的定日镜面形支撑结构优化技术路线. 利用模拟仿真、数值计算和优化算法等方法，解析20 m²定日镜面形定义技术路线的4个组成环节：面形规格及宽高比、上弦杆的截面矩、平面桁架组间距的最优值、机加工中工艺控制要点的量化. 试制小型定日镜进行实验，分析光斑形状和能流密度分布特性，并与理想球面形光斑比较，两者的拟合优度大于0.98. 实验结果表明，当反射镜宽高比取1.2，上弦杆截面矩取40 000 mm⁴，桁架组间距取950 mm，上弦杆和斜杆的开孔公差小于0.9 mm时，反射面形的质量提升. 研究从原理和实践上证明了该优化技术路线的可行性.