Influence of depth-thickness ratio of mining on the stability of a bedding slope with its sliding surface in concave deformation

In order to study the influence of depth-thickness ratio on bedding slope stability, whose sliding surface is flexural concave in shape under mining conditions, this paper aims to study the characteristics of deformation and damage of bedding sliding with depth-thickness ratios of 200:1, 150:1, 120:1, 100:1 and 50:1by adopting numerical simulation analysis software combined with laboratory-made ‘‘under the influence of mining variable sliding surface slope similar simulation test bed", and to propose identification methods for slope stability under the influence of mining. The results show that mining activities under the slope reduce slope stability. With a decrease in the mining depth ratio, the influence of mining on the slope increases gradually, and the damage to the slope gradually expands, the stability of the slope gradually reduces, fracture occurs on the slope toe and the central fissure gradually develops to the surface,and reaches slide threshold when the depth-thickness ratio is 50:1.     

基于解析解的四阶PDE曲面裁剪方法

该文提出了一种可以广泛应用于四阶PDE曲面的裁剪方法。利用PDE的参数域内的曲线在曲面上投影,得到所求裁剪曲面的边界曲线,然后通过边界曲线的导矢与曲面在边界曲线处的法向量得到边界曲线处的跨界导矢,最后以求得的裁剪曲面的边界曲线以及裁剪曲面在边界曲线处的跨界导矢为PDE曲面的边界条件,用四阶的PDE曲面方程求得PDE裁剪曲面。     

基于表面反应和扩散迁移控制的灰岩单裂隙渗流—溶解模型及其数值模拟

针对碳酸盐类可溶岩地区水电站坝址流场、化学场以及固相介质属性等随时间发生改变,从而对工程安全运行造成不利影响等问题,研究了灰岩地区地下水运移过程中各物理场间的相互作用,分析了影响灰岩溶解速率的两个因素,即表面反应控制和扩散迁移控制。在此基础上,建立了单裂隙中的渗流—溶解耦合模型,并进行数值求解。模拟结果表明,在垂直裂隙延伸方向,其溶蚀锋面为非齐整平面,而是呈似“虫洞”状非均一变化,而沿裂隙延伸方向即自上游侧向下游方向溶蚀程度逐渐减轻;而通过裂隙的流量呈现随时间逐渐增大的趋势,但变幅不大;根据流量求得的等效水力隙宽,其增幅和增长速率均小于实际平均隙宽;同时,化学场中Ca2+浓度的分布与裂隙开度变化具有相似性,不同时刻下上游侧反应速率R均大于下游侧。就反应机制而言,在初期均受表面反应控制,而随反应进行,位于上游补给区部位转为受扩散迁移控制,但在下游位置仍受表面反应控制。     

视觉检测系统中亮度不均匀背景的一种去除方法

刀具形状视觉检测系统中，照明不均匀对测量结果影响很大。针对这种情况，提出了基于二维二阶多项式拟合并去除不均匀背景的方法。遵循最小均方程差原理，给出了二维二阶拟合的矩阵表达式。在编制的程序中，拟合点以人机交互形式由鼠标点击选出，程序自动记录所选点的图象人材与亮度值信息，然后拟合出背景曲面，并以二值图象形式给出去除背景后的目标图象。对一幅光照模型未知的网络图象进行了背景去除，实验结果良好。     

Effect of surface coating on the screw loosening of dental abutment screws

Regardless of the type of performed restoration, in most cases, a screw connection is employed between the abutment and implant. For this reason, implant screw loosening has remained a problem in restorative practices. The purpose of this study was to compare the surface of coated/plated screws with titanium and gold alloy screws and to evaluate the physical properties of coated/plated material after scratch tests via FE-SEM (field emission scanning electron microscopy) investigation. GoldTite, titanium screws provided by 3i (Implant Innovation, USA) and TorqTite, titanium screws by Steri-Oss (Nobel Biocare, USA) and gold screws and titanium screws by AVANA (Osstem Implant, Korea) were selected for this study. The surface, crest, and root of the abutment screws were observed by FE-SEM. A micro-diamond needle was also prepared for the scratch test. Each abutment screw was fixed, and a scratch on the surface of the head region was made at constant load and thereafter the fine trace was observed with FE-SEM. The surface of GoldTite was smoother than that of other screws and it also had abundant ductility and malleability compared with titanium and gold screws. The scratch tests also revealed that teflon particles were exfoliated easily in the screw coated with teflon. The titanium screw had rough surface and low ductility. The clinical use of gold-plated screws is recommended as a means of preventing screw loosening.     

用双层辉光等离子法在钛表面制备的Ti-Pd合金层性能研究

采用双层辉光等离子冶金技术在纯钛表面制备了Ti—Pd合金层。其深度大约为90μm，Pd含量呈梯度变化，并出现了TiPd3，TiPd2，Ti2Pd3，Ti3Pd5，TiPd，Ti4Pd等6种化合物相和Pd相。合金层在100℃的NaCl饱和溶液＋HCl溶液以及40℃的8．6％H2SO4溶液中的耐缝隙腐蚀性能优于Ti0．2Pd合金；在室温80％H2SO4的溶液中，腐蚀速率仅为0．682mm／a，是Ti0．2Pd合金的18．2％：在室温30％HCl的溶液中，表面Ti—Pd的腐蚀速率仅为0．004mm／a，是Ti0．2Pd合金的12．5％。     

Solar furnace surface treatment of plasma-sprayed thermal barrier coatings

An original process of superficial thermal treatment is described. This process has been successfully applied to partially stabilized yttria-zirconia coatings (ZrO₂-Y₂O₃) to increase the lifetime of the thermal barriers. A thin superficial layer was melted, and morphological transformations were observed. A microstructural comparison between as-sprayed layers and thermally treated layers is presented.     

液态铝合金表面张力快速检测新方法与装置

表面张力是液态合金的重要物性参数之一,铝合金表面张力与其变质处理效果及充型能力等质量参数密切相关,研究铸造铝合金表面张力快速检测方法及装置,对于开发铝合金熔炼质量炉前实时评价系统具有非常重要的实际意义.介绍了一种液态铝合金表面张力快速测试的新方法和新装置,新方法以固定时间内吹入被测液体的气泡个数以及气泡在生长过程中内部压差变化为信息参数,通过回归公式求解表面张力.基于该方法研制的表面张力新型测试装置由单片机测控单元、探头及其锁紧和升降机构、供气单元等部分构成.采用新装置可在5 s内测得铝合金表面张力,且具有较高的测试精度.     

Effect of surface modification of metal hydride electrode on performance of MH/Ni batteries

A novel method was applied to the surface modification of the metal hydride(MH)electrode of MH/Ni batteries.Both sides of the electrode were plated with a thin silver film about 0.1μm thick using vacuum evaporation plating technology,and the effect of the electrode on the performance of MH/Ni batteries was examined.It is found that the surface modification can enhance the electrode conductivity and decrease the battery ohimic resistance.After surface modification,the discharge capacity at 5C(7.5A)is increased by 212 mA.h and the discharge voltage is increased by 0.11 V,the resistance of the batteries is also decreased by 32%.The batteries with modified electrode exhibit satisfactory durability.The remaining capacity of the modified batteries is 89%of the initial capacity even after 500 cycles.The inner pressure of the batteries during overcharging is lowered and the charging efficiency of the batteries is improved.     

表面氧化层对TiMn1.25Cr0.25储氢合金活化性能的影响

通过TiMn1.25Cr0.25合金粉活化前在空气中暴露不同的时间,探讨了表面氧化层的形成对其活化性能的影响。活化测试结果表明：合金的活化难度随着合金在空气中暴露时间的延长而加大。俄歇电子能谱(AES)结果表明,在空气中暴露后的合金表面形成了一层大约6nm-10nm厚的表面氧化层,正是这层氧化层的形成加大了合金的活化难度。扫描电镜(SEM)结果表明合金的活化过程与合金的碎化有着密切的联系。