CuInS2/SiNWs/Si composite material for application as potential photoelectrode for photoelectrochemical hydrogen generation

This work aims at developing a new composite material based on nanosized semiconducting CuInS₂ (CIS) particles combined with silicon nanowires grown on a silicon substrate (SiNWs/Si) for photoelectrochemical (PEC)-splitting of water. The CIS particles were prepared via a colloidal method using N-methylimidazole (NMI) as the solvent and an annealing treatment. The SiNWs were obtained by chemical etching of silicon (100) substrates assisted by a metal. The CIS/SiNWs/Si composite material was obtained by deposition of an aliquot of a suspension of CIS particles onto the SiNWs/Si substrate, using spin coating followed by a drying step. The XRD pattern demonstrated that CuInS₂ grows in the tetragonal/chalcopyrite phase, while SiNWs/Si presents a cubic structure. The SEM images show semi-spherical particles (～10 nm) distributed on the surface of silicon nanowires (～10 μm). The EIS measurements reveal n-type conductivity for CIS, SiNWs/Si and CIS/SiNWs/Si materials, which could favour the oxidation reaction of water molecules.     

Monolithically-integrated BiVO4/p+-n GaAs1-xPx tandem photoanodes capable of unassisted solar water splitting

Monolithically-integrated tandem photoanodes were fabricated on substrates consisting of epitaxial n-GaAs_1-xP_x (x ? 0.32) grown on n⁺-GaAs wafers. A p⁺-n junction photovoltaic (PV) cell was first formed by zinc diffusion into the n-GaAs_0.68P_0.32 from a deposited ZnO coating. After diffusion the ZnO serves as a transparent electrical contact to the resulting p⁺-GaAs_0.68P_0.32 surface layer. Transparent, conducting SnO₂:F provides chemical and mechanical protection for the ZnO and the underlying PV cell, and it electrically connects this cell to a top BiVO₄ photocatalyst layer. In some photoanodes, a WO₃ thin film was interposed between the SnO₂:F and BiVO₄. All oxide coatings were produced by ultrasonic spray pyrolysis except WO₃, which was spin coated. Unassisted (unbiased) solar water splitting was achieved, with a solar-to-hydrogen efficiency approaching 2%, without addition of any co-catalyst to the BiVO₄ surface. This work can provide insights to other researchers regarding scalable, low cost approaches for the planar monolithic integration of oxide photoanode materials with PV cells to create new tandem devices.     

硫化氢吸收液的电化学分解条件研究

理想的脱硫工艺应满足体积小、费用低、净化度高、无二次污染等要求。在碱性溶液吸收微量硫化氢时同步进行电解，可有效减小设备体积，并将硫化氢转变为氢气和硫磺，不产生恶性气味。为此，实验研究了温度、浓度、电流密度、pH值等因素对电解阳极过程的影响，确定了适宜的电解条件，并在该条件下进行了吸收实验。结果表明，在最佳电解条件下，硫化钠溶液能充分吸收天然气中经变压吸附提浓的硫化氢（800 mg/m³），吸收率大于99.9％。     

橡胶促进剂DM的合成工艺

M氧化生成DM是自由基反应机理，结合微反应器机理，采用分子氧化的反应方式，选用绿色溶剂异丙醇、环境友好型氧化剂H202，一步法制取高品质DM。对反应时间、反应温度、氧化剂用量等因素进行考察，确定最佳工艺条件为：反应时间90min，反应温度55℃，氧化剂不过量，碱过量5％，M—Na溶液M含量30％，加料时N60 min，溶剂用量为M—Na溶液质量的1．5倍，所得产品质量合格，熔点可达180℃。     

一种制氢预转化催化剂还原的新方法

对上海高桥分公司2×10~4m~3/h(标准状态)制氢装置原设计的预转化催化剂还原流程进行了改进。先跳开预转化反应器,利用转化炉制取氢气,再用自产的高纯氢气代替重整氢,对预转化催化剂进行单独升温还原,避免了催化剂在还原初期因发生甲烷化反应而超温失活的问题,使催化剂具有更好的活性和稳定性。     

Estimation and Optimization of the Principal H-Maser Parameters

The scale along the coordinate axes in the equations of motion hitherto used for an H-maser (in relative units) is shown to depend on Q as the quality factor for an H-maser. This hinders both analysis of the operation of the H-maser and optimization of its parameters. The modified equations of motion proposed here do not have that shortcoming. We determine the atomic flux into the bulb that gives the H-maser the best metrological characteristics.     

Biodegradation of monoaromatic hydrocarbons in aquifer columns amended with hydrogen peroxide and nitrate

The ability of indigenous microorganisms to degrade benzene, toluene, ethylbenzene and xylenes (BTEX) in laboratory scale flow-through aquifer columns was tested separately with hydrogen peroxide (110 mg/l) and nitrate (330 mg/l as NO₃⁻) amendments to air-saturated influent nutrient solution. The continuous removal of individual components from all columns relative to the sterile controls provided evidence for biodegradation. In the presence of hydrogen peroxide, the indigeneous microorganisms degraded benzene and toluene (> 95%), meta- plus para-xylene (80%) and ortho-xylene (70%). Nitrate addition resulted in 90% removal of toluene and 25% removal of ortho-xylene. However, benzene, ethylbenzene, meta- and para-xylene concentrations were not significantly reduced after 42 days of operation. Following this experiment, low dissolved oxygen (< 1 mg/l) conditions were initiated with the nitrate-amended column influent in order to mimic contaminated groundwater conditions distal from a nutrient injection well. Toluene continued to be effectively degraded (> 90%), and more than 25% of the benzene, 40% of the ethylbenzene, 50% of the meta- plus para-xylenes and 60% of the ortho-xylene were removed after several months of operation.     

氢电弧等离子体法制备的纳米镍铈粒子的催化特性

利用氢电弧等离子法制备具有储氢特性纳米镍铈粒子，并在气相苯加氢反应中研究了其催化特性，发现其催化活性与储氢特性及表面层中ＮｉＣｅ合金存在有关，且具有高的选择性和热稳定性，这与纳米粒子独特的结构及铈的加入有关。     

工艺因素对金属封装外引线弯曲疲劳的影响

考察了金属封装外壳制造工艺对外引线弯曲疲劳的影响,发现电镀镍是导致外引线弯曲次数明显减少的最主要工艺步骤,且随镀镍层厚度的增加,弯曲次数减少。此外还讨论了外引线的氢含量和晶粒度对引线抗疲劳能力的影响。     

化肥厂合成气及重整氢真空变压吸附制取高纯度氢气

从设计、生产操作和经济效益3个方面阐述了以化肥厂合成气及重氢为原料，通过真空变压吸附（VPSA）装置制取高纯度氢的过程。工业应用结果表明，该制氢工艺是一项操作简便灵活，制氢费用较低的工艺路线。VPSA装置技术和设计上的特点能够保证大的操作弹性、高的产品氢纯度和较高的氢气回收率。在36％－51％的低限负荷下，通过适当调整吸附时间，可获得纯度99％的氢气产品，89％－92％的氢气回收率。