大型X射线光学仪器:单层镜和多层镜的制造与表征

150~500 mm长度的各种X射线光学元件可用于光束导引,光束调整,以及单色化。本文介绍了两种不同的大型X射线反射镜。第一种为单层反射镜,这种反射镜以2°掠入射角在软X射线区(50~200 eV)起全反射镜作用,可用于自由电子激光器,如德国汉堡的FLASH。第二种是多层镜,由于它的布喇格反射特性,适于作为反射镜以0.4~1°的入射角用于硬X射线区(20~50 keV),如层析光束线的同步辐射存储环中。两种反射镜都用最新物理汽相淀积法制备,并用磁控溅射来实现X射线光学应用所需要的优良光学品质。这一淀积工艺使不同批次的镀膜稳定性良好,有利于实际反射镜在优质衬底上的最后淀积。单层镜和多层镜在它们的相关能量范围内都有很高的反射率,表面粗糙度也很低,且在整个光学波长区这些特性表现均匀。文中所叙相关研究都是借助X射线反射计量(XRR)法,透射电子显微镜(TEM)、光学轮廓仪(OP),以及原子力显微镜(AFM)完成的。     

深亚微米同步辐射x射线光刻模拟

用束衍生法研究了深亚微米同步辐射 x射线光刻中掩模吸收体的光导波效应 ,并对 x射线光刻后的光刻胶剖面进行了理论计算。采用面向对象技术 ,研制了一个取名为 XLLS1 .0的模拟软件。本文对这个软件进行了详细介绍     

Chemical Vapor Deposition of Silicon Carbide Epitaxial Films and Their Defect Characterization

A chemical vapor deposition (CVD) system was designed and fabricated in our laboratory and SiC homo-epitaxial layers were grown in the CVD process using silicon tetrachloride and propane precursors with hydrogen as a carrier gas. The temperature field was generated using numerical modeling. Gas flow rates, temperature field, and the gradients are found to influence the growth rates of the epitaxial layers. Growth rates were found to increase as the temperature increased at high carrier gas flow rate, while at lower carrier gas flow rate, growth rates were observed to decrease as the temperature increased. Based on the equilibrium model, “thermodynamically controlled growth” accounts for the growth rate reduction. The grown epitaxial layers were characterized using various techniques. Reduction in the threading screw dislocation (SD) density in the epilayers was observed. Suitable models were developed for explaining the reduction in the SD density as well as the conversion of basal plane dislocations (BPDs) into threading edge dislocations (TEDs).     

金属/氧化物界面形成机理原位研究

金属/氧化物界面是控制反应机理和宏观性质的关键区域.原位表征手段可以实时、连续、动态地对金属/氧化物界面形成过程进行研究,其观察和分析结果对理解界面形成过程及其应用有重大学术意义和工程价值.本文综述国内外原位表征金属/氧化物界面的研究工作,主要关注原位透射电子显微镜、原位同步辐射技术、原位中子技术等先进表征分析金属/氧...     

Fast microwave detection system for coherent synchrotron radiation study at KEK: Accelerator test facility

A fast room temperature microwave detection system based on the Schottky Barrier-diode detector was created at the KEK ATF (Accelerator Test Facility). It was tested using Coherent Synchrotron Radiation (CSR) generated by the 1.28 GeV electron beam in the damping ring. The speed performance of the detection system was checked by observing the CSR from a multi-bunch (2.8 ns bunch separation time) beam. The theoretical estimations of CSR power yield from an edge of bending magnet as well as new injection tuning method are presented. A very high sensitivity of CSR power yield to the longitudinal electron distribution in a bunch is discussed.     

In situ analysis of the strain evolution during welding using low transformation temperature filler materials

ABSTRACT

Compared to conventional welding consumables using low transformation temperature (LTT) filler materials is an innovative method to mitigate tensile residual stresses due to delayed martensite transformation of the weld. For the effective usage of LTT filler materials, a deeper understanding of the complex processes that lead to the final residual stress state during multi-pass welding is necessary. Transformation kinetics and the strain evolution of multi-pass welds during welding were investigated in situ at the beamline HEMS@PETRAIII, Germany. Compared to conventional welds, the total strain was reduced and compression strain was achieved when using LTT filler materials. For an optimal use of the LTT effect in the root of multi-pass welds, the alloying concept must be adapted taking care of dilution.     

两种3D打印用雾化Ti-6Al-4V粉末的对比研究

本研究分别利用水冷铜坩埚真空感应熔炼气雾化(VIGA-CC)和等离子旋转电极(PREP)两种技术制备出球形Ti-6Al-4V合金粉末,作者利用SEM、同步辐射CT扫描-三维重建和氩气含量测试等分析手段对不同粒径的Ti-6Al-4V合金粉末的孔洞缺陷和氩气含量、硬度值进行了表征。实验结果表明, VIGA-CC粉末粒度分布宽,细粉收得率较多,粉末粒度分布在40~180 μm之间, PREP粉末的粒度分布较窄,主要集中在110~180 μm之间;金属粉末内部的孔隙率、气体含量和孔尺寸随着粉末粒度的增大而增大,且同一粒径范围内VIGA-CC粉末的气孔概率多于PREP粉末;随着粉末粒径减小,粉末截面组织逐渐细化,其硬度值逐渐升高,整体上VIGA-CC粉末硬度值高于PREP粉末。