高温下具有弹性支座钢构件的动力稳定荷载

根据弹性稳定理论原理研究了弹性支座钢构件在高温环境下的动力特性问题,导出了高温下杆件的动力稳定临界荷载计算式,并讨论了保护层厚度、长细比、阻尼、材料特性等因素对杆件动力稳定临界荷载的影响,探讨了在实际工程中如何减小结构失稳的问题,可为钢结构抗火设计提供参考.     

某水电站拱坝施工期温度仿真分析

拱坝施工期的温控防裂研究是设计和施工期需要特别关注的问题之一.采用三维有限单元法对某水电站拱坝碾压混凝土坝段和常态混凝土坝段的施工期温度场进行仿真分析.计算结果表明,薄层浇筑的层面散热效果好,层厚超过3 m后效果不明显;不同季节的层面散热效果差异较大,浇筑气温越低,层面散热效果越好;常态混凝土溢流坝段自由冷却时间较长,须采取坝体二期冷却措施,以保证按期进行接缝灌浆.     

隧道窑预热带烟气流动对上下温差的影响

为减小隧道窑预热带上下温差,利用计算机数值模拟对预热带温度场进行研究,找出烟气流动对隧道窑预热带上下温差的影响规律.在预热带内来流烟气的温度保持不变,速度为0.5～1.0 m/s时,窑内温度均匀性较好.在保持来流烟气温度和速度不变的情况下,码料密度的合适值为孔隙率在0.208～0.408范围内,可提高产品的质量和产量.     

中国石化武汉分公司低温热能的利用

介绍了中国石化武汉分公司低温热利用节能改造情况．利用催化裂化装置的顶循环油直接做气分塔底热源以及催化塔顶油气加热热媒水,取代原来的蒸汽加热,为气分装置提供塔底重沸器热源．通过能量的梯级利用,有效解决了全厂热源能级利用不合理的问题．项目投用后,节能效果显著,武汉分公司可以节约1．0MPa蒸汽184．8kt／a．     

Carbon spheres prepared via solvent-thermal reaction method and their microstructures after high temperature treatment

Carbon spheres with size of 50–300 nm were synthesized via a solvent-thermal reaction with calcium carbide and chloroform as reactants in a sealed autoclave. The morphologies and microstructures of carbon spheres before and after high temperature treatment (HTT) were characterized by X-ray diffractometry (XRD), scanning electronic microscopy (SEM), energy diffraction spectroscopy (EDS), and transmission electron microscopy (TEM). The formation mechanism of carbon spheres was discussed. The results indicate that the carbon spheres convert to hollow polyhedron through HTT. Carbon spheres are composed of entangled and curve graphitic layers with short range order similar to cotton structure, and carbon polyhedron with dimension of 50–250 nm and shell thickness of 15–30 nm. The change of solid spheres to hollow polyhedron with branches gives a new evidence for formation mechanism of hollow carbon spheres.     

Structure of Bi2O3-ZnO-B2O3 system low-melting sealing glass

Bi_2O_3-ZnO-B_2O_3 system glass is a kind of lead-free low melting sealing glasses. The structure of Bi_2O_3-ZnO-B_2O_3 system low-melting sealing glass was investigated by DSC, FT-IR, XRD and SEM. The results show that with the increase of B_2O_3 content, the transition temperature Tg and softening temperature T_f of Bi_2O_3-ZnO-B_2O_3 system low-melting sealing glasses increase, which leads to the liquid phase precipitation temperature increasing and promotes the structure stability in the glass. With increasing the heat treatment temperature, a large number of liquid phases appear in samples and the sinter efficiency of the samples increases. The FT-IR spectra of the glasses show the presence of some bands that are assigned to vibrations of Bi-O bond from [BO_3] pyramidal and [BiO_6] octahedral units and B-O from [BO_3] and [BO_4] units. With the decrease of B_2O_3 content, the crystallization tendency of the glass increases. In glass samples B_1 and B_2, crystallization starts at 460 ℃ and 540 ℃, respectively. Both of them precipitate Bi-(24)B_2O_(39) phases.     

卷取温度对X80管线钢析出行为与性能的影响

观察了不同卷取温度下X80管线钢中析出物的情况,并结合其组织性能对比可知：在实验情况下,480℃卷取时,有大量细小弥散的Nb、V的碳氮化物析出物,起到了较好的析出强化作用.     

注汽锅炉高含盐回用水引发爆管分析

辽河油田锦州采油厂注汽锅炉采用回注水生产蒸汽,由于回注水水质超标使二氧化硅和盐在过热段结垢和结晶,造成炉管局部过热,导致炉管材料的许用应力急剧下降,发生爆管。由于注汽锅炉使用油作燃料,火焰最大直径为3m,二氧化硅和盐在此同时结垢和结晶,这两种最恶劣工况同时在此发生,导致爆管。降低蒸汽干度或干度交替变化,使这两种最恶劣工况在此不同时发生是解决问题的主要方法。     

Si(111)上生长LiNbO_3薄膜的研究

利用射频磁控溅射的方法,在Si(111)衬底上制备了LiNbO3薄膜。采用X射线衍射(XRD)和扫描电子显微镜(SEM)研究了衬底温度、退火温度和溅射气体压强对LiNbO3薄膜结晶和表面形貌的影响,并用椭圆偏振仪测量了薄膜的厚度和折射率。结果表明:衬底温度为450℃时制备的薄膜,退火前后都没有LiNbO3相生成;衬底温度为500～600℃时,LiNbO3薄膜出现(012)、(104)和(116)面衍射峰,经600℃退火后3个衍射峰的强度加强;衬底温度为600℃时,经600～900℃退火得到的LiNbO3薄膜,除出现(012)、(104)和(116)面衍射峰外,还出现(006)面衍射峰;溅射气体压强从0.8 Pa增大到2.4 Pa时,经800℃退火后得到的LiNbO3薄膜表面晶粒团簇变小,而0.8 Pa制备的薄膜经800℃退火后LiNbO3相的结晶程度较其它压强下完善;900℃退火后得到的LiNbO3薄膜折射率为2.25,与LiNbO3晶体相当。     

液体温度对空泡生长和溃灭过程的影响

采用光偏转测试系统研究了不同温度纯净水中激光空泡脉动过程,通过实验获得了激光空泡在靶表面膨胀和收缩全过程,确定了空泡的最大、最小泡半径、脉动周期和泡壁运动速度。实验采用0℃到70℃的纯净水,测量了空泡的泡半径和脉动周期等特征参量变化情况。实验结果表明,液体温度是影响空泡脉动的一个非常重要的因素,随着液体温度的增加空泡的最大泡半径和溃灭周期均呈增加趋势。给出了相应的理论解释。