PET熔体输送系统中熔体温度自动控制方案

在热媒温度控制系统中以熔体温度作为主参数,组成串极调节系统。投入运行后,熔体温度稳定,调节阀动作平稳,效果良好。     

6m大容积焦炉烘炉实践与体会

介绍了 6 m大容积焦炉由冷态到转入正常加热温度的烘炉操作过程中 ,按照一定的升温曲线 ,通过对焦炉热工和炉体膨胀的科学管理 ,确保新建焦炉顺利由冷态过渡到生产状态。     

环糊精和表面活性剂在室温磷光中的应用

介绍了环糊精和表面活性剂作为有序介质在室温磷光中的研究进展．并对各种方法的特点和应用情况作了简要概括。认为环糊精和表面活性剂混合介质能大大提高发光物质的室温磷光．而且操作简便．应用前景广阔。     

甲基葡萄糖甙（MeG）水溶液工艺改进试验

介绍了用５次以上的母液生产ＭｅＧ水溶液工艺的改进试验。     

Tensile Stress Relaxation of Alumina at High Temperature

The development of a tensile testing methodology for ceramics which enables a stress vs strain-rate response to be measured at high temperature is described. The test involves a carefully controled stress relaxation test at constant total strain using an experimental procedure and phenomenological analysis previously developed for metallic materials. It is demonstrated here with preliminary tests on alumina at 1050° and 1150°C. This offers, with further development, the possibility of establishing design stresses associated with low strain-rate behavior for structural applications. The results demonstrate that data covering four decades of strain rate may be generated in tests lasting a few hours. The inelastic strain consists of substantial anelastic recoverable strain in addition to a permanent creep strain.     

高柔韧性聚氨酯丙烯酸酯的合成及应用

选用不同结构的多元醇作骨架，合成一系列高性能的聚氨酯丙烯酸树脂，并通过对聚氨酯丙烯酸树脂性能的对比研究，发现以聚丁二烯二元醇为骨架的聚氨酯丙烯酸酯树脂具有极佳的柔韧性和优异的低温耐曲折性。     

低密度泡沫玻璃的研究与应用

低密度泡沫玻璃是利用碎玻璃制造的一种气孔率大于90%的隔热保温材料,它具有强度高、导热系数小、吸水率低、不吸湿、耐腐蚀等特性,在潮湿环境下抗冻性能好,是一种优良的低温、超低温隔热保温材料。该产品用途广泛,所用的原材料简单易得,但生产工艺过程比较复杂,生产过程控制精度要求较高,容易产生各种缺陷而影响产品的质量。本文对低密度泡沫玻璃的生产工艺过程进行详细的分析研究,提出相应的措施,确保产品的低密度和高成品率,提高产品的性能,扩大产品的使用范围。     

近十年常温干法精脱硫专利技术发展动态

收集了近十年来国内的常温干法精脱硫专利，并分类列举出各种脱硫剂的物化性质和几种常温精脱硫工艺，重点阐述了该技术的优缺点及其未来发展方向。     

High temperature polymerization of propylene catalyzed by MgCl2‐supported Ziegler–Natta catalyst with various cocatalysts

Four cocatalysts, referred to as ethylaluminoxanes, were synthesized by the reaction between triethylaluminium (AIEt₃) and water under various molar ratios of H₂O/Al at ?78°C. Aluminoxanes were used as cocatalysts for a MgCl₂‐supported Ziegler–Natta catalyst for propylene polymerization at temperatures ranging from 70 to 100°C. When the polymerization was activated by AlEt₃, the activity as well as the molecular weight and isotacticity of the resulting polymer gradually dropped as the temperature varied from 70 to 100°C. When ethylaluminoxane was employed as the cocatalyst, good activity and high molecular weight and isotacticity were obtained at 100°C. Furthermore, when the cocatalyst varied from AlEt₃ to ethylaluminoxane, the atactic fraction and polymer fraction with moderate isotacticity decreased and the high isotactic fraction slightly increased, which indicated that the variation of the cocatalyst significantly affects the isospecificity of active sites. It was suggested that the reactivity of the Al‐Et group and the size of the cocatalyst were correlated to the performance of the Ziegler–Natta catalyst at different temperatures. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 1978–1982, 2006     

Effect of Twin-Plane Reentrant Edge on the Coarsening Behavior of Barium Titanate Grains

When BaTiO₃ ceramics were sintered at relatively low temperatures (≤1250°C), the grains with reentrant edges caused by a (111) double twin grew exclusively. As a result, a microstructure with a bimodal grain-size distribution composed of platelike large grains and fine matrix grains was obtained. In contrast, at the usual sintering temperature between 1250° and 1350°C, grains containing a (111) double twin did not exhibit any growth advantage. In this case, a coarse and uniform microstructure was obtained. When this coarse-grained specimen was further heat-treated at 1365°C, the grains possessing a double twin were observed to grow exclusively again. The results were explained in terms of a coarsening process controlled by two-dimensional nucleation.